Summary of Contents for Touchboards Vidifox DV 480
Page 1
® Vidifox Document Camera DV 480 USER MANUAL Please read this User Manual thoroughly before you use the document camera. Keep the CD-ROM in a convenient place so you can use it quickly if you need to. Please visit us at http://www.waninusa.com where you can get product support, the latest driver updates, and answers to frequently asked questions (FAQs) and technical questions.
Page 2
PRECAUTIONS NOTICES: PLEASE READ CAREFULLY BEFORE USE Use the document camera under the rated electric conditions. Do not place the document camera on any unstable surface. It may fall and cause injuries or damages. Do not place this device directly under sunlight or near heaters. ...
BASIC SETUP 1. Unpack, put aside all packing materials. 2. Unfold the light arms until reaching the end position. 3. Raise the camera arm completely. Rotate the camera head until the lens face the center of the base unit.
PARTS IDENTIFICATION 1. camera cover 2. camera lens 3. upper mechanical arm 4. main mechanical arm 5. side lamp 6. lighting arm 7. power switch 8. base light 9. control panel 10. base unit 11. infrared receiver...
CONTROL PANEL DOC: Press this button for shorter than 3 seconds to display the image on the platform. If pressing DOC for longer than 3 seconds, the camera will stop transmitting image and go to standby; pressing for another 3 seconds, the camera will come back to work. C-VIDEO S-VIDEO: Switch the input between Composite Video and S-Video.
BUTTON INSTRUCTION REMOTE CONTROL 1. Home: Press for shorter than 3 seconds to output the current image of the camera. Press this button for longer than 3 seconds to adjust color and white balance automatically. 2. PC: Switch the input VGA source between PC1 and PC2. 3.
enhances the black and white contrast to increase the readability of the text. 5. FRZ: Freeze and unfreeze the image. 6. P/N: Switch the image between positive and negative mode. 7. MIR: Switch the output image between the right/left mirrored image, up/down mirrored image and original image.
Page 9
MIC:Microphone input RGB AUDIO IN 1/2: Audio input for RGB input 1/2 AUDIO OUT: Audio output RGB IN 1/2: RGB signal input 1/2 (15 pin D-SUB) RGB OUT 1/2: RGB signal output 1/2 (15 pin D-SUB) RS-232: Allow a computer or external control system to control the document camera via this port.
3. Composite Video output connection To Audio Input To Video Input Video Cable 4. Computer connection Audio Cable To Audio Output RS232 To RGB Output...
5. DVD or other video input connection DVD Player 1 To Audio Output(L) Audio cable To Audio Output(R) To Video Output Video cable To S-Video output DVD player 2 S-Video cable To audio output(L) Audio cable To audio output(R) Access Basic Functions: 1.
For sharper image, engage the text mode by pressing the T/P button. 3. Showing the 3D objects: Use the FOCUS+ and FOCUS- buttons on the control panel to manually focus on any part of the 3D object. 4. Showing the transparent material such as an overhead transparency Press the LAMP button until the built-in light box is on.
Page 14
Then you will see the software setup window: Click Next>, you will see:...
Click Next>, you will see: Click Finish to finish software installation. Please pay attention to the following: 1. Computer hardware requirement: CPU: 2.4GHz, RAM: 256M or above, Graphic card 64M, USB 2.0 port, Hard disk 40G or more, Monitor display resolution higher than XGA (1024 x 768).
tilt the camera by hand. LIGHT Press “LAMP” to switch between arm light, back light and no light. ZOOM IN AND ZOOM OUT Press " ZOOM+"or "ZOOM-" POSITIVE/NEGATIVE CONVERSION Press the N/P button, the output image will be converted to negative color. Press it again, the output image will be converted back to original color.
COLOR ADJUSTMENT To adjust white balance automatically, (a) press "AUTO" button on the control panel, or (b) press the "Home" button on the remote control for 3 seconds. IMAGE FREEZE The freeze function allows you to discretely prepare the next image without interrupting current presentation.
USB 2.0 PORT The USB port can be used to capture still images from the DV 480 into a computer. In this way, the DV 480 can be used as a 3-D scanner for your computer. Connect the DV 480 to your computer with the supplied USB cable. The capture software is available on the supplied CD-ROM.
Page 19
To capture the video, please follow the steps below: Insert the provided CD-ROM into the computer. Create a folder on the hard drive and name it DV 480. Then copy the RS232 and USB application on the provided CD into this folder.
Page 20
3. Click File->Set Capture File, to set the capture file.
Page 21
a. Set the location where the file is to be saved to and file name. b. Set the file size.
Page 22
4. Click OK to finish the setup and click Capture->Start capture to capture video. 5. You will see the following window, Click OK to start capture.
6. Click Capture->Stop Capture to stop RS232 CONTROL The DV 480 can be controlled from a computer via the RS232 port. Open the DV 480 folder you just created and open the RS232 folder. 2. Connect the computer and the DV 480 with a RS232 cable and turn on the power of the DV 480.
Page 24
Then you will see the software setup window (Described on Page 15-17) 4. Double click or click start->All Programs->The DV 480 Control Program->The DV 480 to run the RS232 software, you will see a tool bar: The definition of each button is Zoom in, Zoom out, Auto focus, Functions, minimize. Click Functions, you will see the following control panel.
FOLDING THE UNIT 1. Fold the right arm light down first onto the base, then the left arm down. Rotate the camera head clockwise until the camera head is parallel to the camera stand. 2. Rotate the camera head clockwise until the camera head is parallel to the camera stand.
SPECIFICATIONS Model No. DV 480 Sensor 1/3" CMOS Total pixel 2 Megapixel Zoom 8x optical, 12x digital Frame rate Shooting area Max: 13.5" x 10.6" Min: 0.1" x 0.1" Focus Auto/manual Native output signal SXGA (1280 x 1024) Converted output signal XGA (1024 x 768) Resolution (Horizontal) More than 750 TV lines...
Arm Light × 2 (LED) Light source 8”x10” Lightbox (LED) 32° F to 104° F Operating temperature 0° C to 40° C Folded: 15.9" x 16.7" x 6.1" 40.4 cm x 42.4 cm x 15.5 cm Dimensions Setup: 18.7" x16.7" x 22.3" 47.5 cm x 42.4 cm x 56.6 cm Power supply 12V DC power adapter...