Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for ICP PAC-170
- Page 1 PAC-170 CHASSIS USER’ S MANUAL...
-
Page 2: Copyright Notice
Copyright Notice This document and product is copyrighted, October 1998, by ICP Electronics Inc. All rights are reserved. No part of this manual may be reproduced, copied, or translated without prior notice to ICP Electronics Inc. The information provided in this document is for reference only. We do not assume any responsibility arising out of the application of the products. -
Page 3: Table Of Contents
1.1 General Information 1.2 Product Specifications 1.3 Dimensions Chapter 2 System Setup 2.1 Front Panel of PAC-170 2.2 Rear Panel of PAC-170 2.3 Removing the chassis cover 2.4 The Backplane and Card Clamp Installation 2.5 Disk Drives Installation 2.6 Replacing the Filter 2.7 Power Supply Installation... -
Page 4: Chapter 1 Product Information
Chapter 1 Product Information 1.1 General Information PAC-170 IPC chassis is a rugged PC/AT compatible computer designed for the factory floor and other Industrial harsh environment.PAC-170 features 7 slots Passive Backplanes and high reliability AC Input Power Supply ACE-925A. The chassis can easily be mounted on panels or walls with the supplied brackets. -
Page 5: Working Environment
Working Environment - Operating Temperature 0~50°C - Relative Humidity 5~95% Relative - Vibration 5-17Hz, 0.1” double amplitude displacement 17-640Hz, 1.5G acceleration peak to peak - Shock 10G acceleration peak to peak - Safety approval meet CE, FCC - Shipping Weight 10Kgs Cooling Fan One ball bearing fan for system cooling... -
Page 6: Dimensions
1.3 Dimensions 210.00mm R2.5 193.00mm 230.00mm -- 5... -
Page 7: Front Panel Of Pac-170
Chapter 2 Installation Procedure The following set up procedures are provided to assist you in installing the system unit, please follow the steps below: 2.1 Front Panel of PAC-170 KEYBOARD H.D.D-LED SWITCH POWER RESET POWER-LED SWITCH -- 6... -
Page 8: Rear Panel Of Pac-170
2.2 Rear Panel of PAC-170 AC-OUTPUT AC-INPUT -- 7... -
Page 9: Removing The Chassis Cover
2.3 Removing the chassis cover The cover is mounted by six screws on the top of the chassis, remove them and slide the cover to the rear of the chassis. Figure below shows how to remove the chassis cover. Step 2 Step 1 -- 8... -
Page 10: Backplane Installation
2.4 Backplane Installation Figure below illustrates how to install the backplanes on the PAC-170 -- 9... - Page 11 Step 1 Step 2 -- 10...
-
Page 12: Disk Drives Installation
2.5 Disk Drives Installation 1.Remove the disk drive bay 2.Mount the drive rails on the front of HDD or FDD 2.Attach the FDD to the bracket with four screws and connect FDD cable & power cable to the FDD. 3.Attach the HDD to the bracket with four screws and connect a 40-pin flat cable &... - Page 13 Step 1 Step 2 -- 12...
-
Page 14: Replacing The Filter
2.6 Replacing the Filter The filter of the PAC-170 is located at the front end of the chassis. Under continuous use, the filter should be removed about once a mounth. To replace the filter, open and close the door by press . Take out the old filter and slide the new one into place . - Page 15 -- 14...
-
Page 16: Power Supply Installation
2.7 Power Supply Installation BACKPLANE ACE-925A POWER SUPPLY Brown Blue POWER SWITCH Brown Black White Blue Black White -- 15... -
Page 17: Fan Installation
2.8 Fan Installation ACE-925A POWER SUPPLY +12V (RED) GND (BLACK) -- 16... - Page 18 APPENDIX A PASSIVE BACKPLANES 0.00 10.00 165.00 175.00 -- 17...
- Page 19 APPENDIX B EXPLODED DIAGRAM -- 18...