Advertisement
stabilize themselves to the ambient temperature.
For best results, use in ambient temperatures that
range from +32 to 104°F (0 to +40°C).
For any other "Er" error messages it is necessary to
reset FlashPoint's circuitry. To reset, turn the
instrument off, remove the battery and wait for a
minimum of one minute, then re-insert the battery
and turn the unit on. If the error message remains
please
contact
Hobby
assistance. Dispose of used lithium batteries
properly and keep away from children.
ON-SCREEN BATTERY INDICATOR
FlashPoint's custom LCD incorporates a built-in
battery
power
indicator
condition of the on-board battery, which functions
as follows:
"Full Battery:" Temperature measurement
fully functional.
"Partially Full Battery:" Battery needs
to
be
measurements are possible.
"Low Battery:" Temperature measurements
are no longer accurate or possible.
BATTERY REPLACEMENT
When the battery power icon indicates the on-board
battery is low, the battery should be replaced
immediately ONLY with CR2032 lithium cell, which
are commonly found at major retail stores. The
battery is located under the twist cover on the rear of
the case. Please Note: It is important to turn the
instrument off before replacing the battery;
otherwise it could cause the FlashPoint to
malfunction. When replacing the battery, make sure
the "+" symbol is facing outward!
WRIST STRAP & BELT CLIP
To attach the included wrist strap, insert the thin
thread into the holes (located on the bottom, rear
of the temperature gauge). Pass the thick part of
the wrist strap through the middle of the thin
thread (see picture for details).
A belt clip is also located on the back of the
temperature gauge, for easy portability if you do not
wish to use the wrist strap. Be sure not to bend the
belt clip past reasonable limits, as it could wear and
possibly break.
Entire Contents © 2006 Made in Taiwan
Services
for
that
indicates
replaced,
but
temperature
1
FlashPoint's sensor lens is the most delicate part of
the gauge. The lens should be kept clean at all times.
Care should be taken when cleaning the lens using
only a soft cloth or cotton swab with water or rubbing
alcohol, allowing the lens to fully dry before using
further
FlashPoint. Do NOT submerge any part of FlashPoint
in any liquid. FlashPoint should be stored at room
temperature between +50 to 72°F (+10 to +40°C).
DuraTrax warrants this product to be free from defects in materials
the
and workmanship for a period of one (1) year from the date of
purchase. During that period, we will repair or replace, at our option,
any product that does not meet these standards. You will be required
to provide proof of purchase date (invoice or receipt). If during the one
year period, your DuraTrax product shows defects caused by abuse,
misuse, alteration or accident, it will be repaired or replaced at our
option, at a service charge not greater than 50% of the current retail
price. Be sure to include your daytime telephone number in case we
need to contact you about your repair. This warranty does not cover
components worn by use, application of reverse voltage, cross
connections, poor installation, subjection of components to foreign
materials, any alterations to wires, or tampering. In no case shall our
liability exceed the original cost of the product.
Your warranty is voided if...
A.
You tamper with any of the electronic components.
B.
You allow water, moisture, or any foreign material to enter the case.
Under no circumstances will the purchaser be entitled to
consequential or incidental damages. This warranty gives you specific
legal rights, and you may also have other rights which vary from state
to state. If you attempt to disassemble or repair this unit yourself it
may void the warranty.
For service on your DuraTrax product, either in or out of warranty,
send it post-paid and insured to:
2
STORAGE & CLEANING
WARRANTY
HOBBY SERVICES
3002 N. Apollo Drive, Suite 1
Champaign, IL 61822
(217) 398-0007
E-mail: hobbyservices@hobbico.com
Internet address: www.duratrax.com
DTXZ1058 For DTXP3100 V1.1
Advertisement
