Panasonic DMP-BD55 Operating Instructions Manual page 39

TV screen and video
Page
The images trom this unit
• Make sure that the television is connected to either the VIDEO OUT terminal,
11
do not appear on the COMPONENT VIDEO OUT terminals or HDMI AV OUT terminal on this unit.
television.
• Make sure that the television's input setting (e.g., VIDEO 1) is correct.
-
• An incorrect resolution is selected in "Component Video Resolution", when the 32
Picture is distorted. television is connected to COMPONENT VIDEO OUT terminals. While stopped,
press and hold [.] and
(~]
(PLAY) on the main unit at the same time for more
Jittering occurs.
than 5 seconds to cancel this setting. Set the item again.
• If "24p Output" is set to "On" when the unit is connected to a TV through any
32
terminal other than HDMI, images may not display properly. In this case, set "24p
Outpuf' to "Off'.
• When "24p Outpuf is set to "On", HDMI authentication takes place where 24p
32
images switch to other images, and a black screen is displayed.
• When "24p Outpuf is set to "On". jittering may occur while playing DVD-Video
32
other than 24p images. In this case, turn "24p Output" to "Off'.
• 1!m3:
Images may not be output due to how files were created.
-
• Press [.] and
[~]
(PLAY) simultaneously on the unit for more than 5 seconds to 33
shift to more compatible mode with HDMI equipment. However, Dolby Digital
Plus, Dolby TrueHD, and DTS-HD audio are not output in bitstream. To output the
bitstream, select "Restore Default Settings" to restore the factory presets and
make proper settings.
• Picture may not be seen when more than 4 devices are connected with HDMI
--
cables. Reduce the number of connected devices.
The screen changes • When the "Screen Saver Function" in the Setup menu is set to "On", the display
32
automatically. may return to the screen saver mode automatically if there is no operation for
10 minutes or more.
Video is not output in high
• High definition video cannot be output through the VIDEO OUT terminals.
-
definition. • Confirm that the "HDMI Video Mode", "HDMI Resolution", and "Component Video
32
Resolution" in the Setup menu are set properly.
The
4:3
aspect ratio picture • Use the television to change the aspect. Refer to your television's operating
-
expands left and right. instructions.
• When using a component video cable, set "Progressive" to "Video". If the situation
29,32
Screen size is wrong. is not restored after that, set "TV Aspecf' to "4:3 Pan & Scan".
• When using an HDMI cable, change "TV Aspect" type to "16:9".
32
There Is a lot ot after-image • Turn "3D NR" or "Integrated NR" off if it is on.
29
when playing video.
When playing DVD-Video
• When you use the HDMI AV OUT terminal for video output, follow the steps below
32
using progressive output,
for setting.
one part of the picture 1 Connect this unit to the TV with any cable except the HDMI cable.
momentarily appears to be 2 When you connect with the Component Video cable, set "HDMI Video Mode" to
doubled up.
"Off" and "Component Video Resolution" to "480i" in the Setup menu.
Still pictures (JPEG) do not
• The images that were edited on the PC, such as Progressive JPEG, etc., may not
35
playback normally.
playback.
Sound
No sound.
• Check the connections and the "Digital Audio Outpuf' settings. Check the input
11-13,31
Low volume. mode on the amplifier/receiver if you have connected one.
Distorted sound.
• Press [AUDIOI to select the audio.
20
Cannot hear the desired
• IBossi: When the unit is connected to an amplifier/receiver with the AUDIO OUT
32,34
audio type.
terminal, set "Analog Audio Output" and match multi channel speaker settings. If
these are not set properly, the audio is not output correctly.
• 1 BOSS
I: When connected to an amplifier/receiver or any other devices using both
32
AUDIO OUT terminal and HDMI AV OUT terminal, the audio from AUDIO OUT
terminal may not be output with the desired audio depending on the specifications
of the connected deVices, etc. Set "HDMI Audio Output" to "Off", when you output
multi-channel surround sound from AUDIO OUT terminal.
• The sound effects (Re-master, V. Surround, etc.) will not work when the bitstream
-
signal is output from the HDMI AV OUT terminal or the DIGITAL AUDIO OUT
terminal.
• 1m!D:
Audio may not be output depending on how files were created.
-
• Audio may not be heard when more than 4 devices are connected with HDMI
-
cables. Reduce the number of connected devices.
• To output audio from a device connected with an HDMI cable, set "HDMI Audio
32
Output" to "On" in the Setup menu.
Cannot switch audio.
• There are discs for which audio cannot be changed because of how the disc was
-
created.
• When connecting an amplifier/receiver using a coaxial cable ('B055,), optical
12,13,31
digital audio cable or an HDMI cable, you cannot switch the audio if "Dolby D/
Dolby D +/Dolby TrueHD" or "DTS/DTS-HD" is set to "Bitstream". Set "Dolby D/
Dolby D +/Dolby TrueHD" or "DTS/DTS-HD" to "PCM" or connect using AUDIO
OUT terminal.
.---------
I
I
/ ' ''\ 1
-,._-----_._------_._--_._--_._---_._- ..
__
_---------.---_
..
-
----
_---_
_------
~
RQT9243