Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Park Flite Mirage 2000
Summary of Contents for Park Flite Mirage 2000
-
Page 2: Instruction Manual
RTF Model Congratulations on purchasing the Mirage 2000 RTF INSTRUCTION MANUAL Top Gun Park Flite are proud to present this high The owner – pilot of this model should take note of performance ducted fan sport scale model of the... -
Page 3: Specifications
KIT CONTENTS AND DESCRIPTION Fuselage with ducted fan, motor, Electronic Speed Control (ESC) receiver, rudder- steering SPECIFICATIONS servo, pushrods and nose wheel. Wing span: 680mm (26.75”) Two delta wing panels with ailerons connected to Length: 980mm (38.5”) factory installed servos Wing Area: 13 Dm (200 sq inches) -
Page 4: Fuselage Assembly
FUSELAGE ASSEMBLY. Supplied complete and ready for use with ducted fan unit using high performance brushless in runner motor. 25Amp Electronic Speed Control (ESC) prewired to motor with extended leads to forward battery box and hinged cover. WING ASSEMBLY. Supplied as two halves. Sprung steerable nose wheel assembly. -
Page 5: Section 2: Battery And Charger
SECTION 2: BATTERY AND CHARGER BATTERY AND CHARGER WARNING: A lithium polymer (LiPo) battery rated at 15C (19.5A) discharge and fast charger is included as part of this package, these cells must be operated with care to prevent the risk of fire. BATTERY AND CHARGER 11.1V (3 cell) 1300mAh (C) LiPo Battery rated at LiPo Batteries are soft cased and can be easily... - Page 6 The RIR 4EXA is a fully proportional 4 function 35Mhz transmitter The transmitter is supplied in a Mode 2 configuration. Mode 2 is also known as Throttle Left. The left stick controls Throttle and rudder movement. The right stick controls aileron and elevator Push the white balance plug of the battery into the movement.
-
Page 7: Section 3: Assembly
Switches 1 to 4 are electronic servo reversing switches and should be adjusted to give the correct control surface deflections relative to stick movements. The mix switch activates a ch1-ch2 mix to give elevon (2 servos both functioning as ailerons and elevators) for delta winged aircraft For the Mirage the switch must be in the ‘Mix’... - Page 8 Apply adhesive to the canard and insert into the SECTION 3: ASSEMBLY CONTINUED slot. Locate the plastic nose cone and apply a bead of adhesive to its inside edge. Be sure to fit canard with its top face sloping down. Push onto the fuselage, wipe off excess adhesive and allow to dry.
-
Page 9: Section 4: Final Set Up
Uncoil the receiver aerial and fully extend to hang off the rear of the aircraft. Be sure to fit with pointed face forward. Construction is now complete and the following steps can be considered as part of the daily Check that all controls operate in the correct assembly and rigging of the model. -
Page 10: Section 5: First Flight
SECTION 5: FIRST FLIGHT FLYING BEFORE THE TEST FLIGHT The Mirage 2000 is capable of 5 to 10 minute flight times and can R.O.G (Rise Off Ground) from smooth On completion of the model take time to test the metalled runways. A hand launch will be required If model in the workshop. - Page 11 Control throws set during assembly will produce a model capable of flying smooth scale like performance and medium to high speed aerobatic manoeuvers. The control surface movements can be increased by moving the clevis connectors nearer to the control surfaces. To reduce movements move the pushrod connections nearer to the servo on the output arms and further out along the control surfaces horns.
- Page 12 TOP GUN PARKFLITE MIRAGE 2000 SPARE PARTS LIST TGP0180 Mirage 2000 EDF EP Fuselage TGP0186 Mirage 2000 EDF EP Ducted Fan TGP0181 Mirage 2000 EDF EP Main Wing Set w/o Motor TGP0182 Mirage 2000 EDF EP Nose, Canopy, TGP0535 TGPF Outrunner Motor (Mirage)