Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for M2 Antenna Systems 2M-1K2
Summary of Contents for M2 Antenna Systems 2M-1K2
- Page 1 Model No: 2M-1K2 2M High Power Amplifier Operating Instructions PLEASE READ BEFORE USE AND SAVE M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722 Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com ©2011 M2 Antenna Systems Incoporated 3/1/12...
-
Page 2: Table Of Contents
Parts List............12 Specifications ..........13 WSJT: What Is It and How Do I Get It? ..14 WARRANTY ............16 M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722 Tel: (559) 432-8873 / Fax: (559) 432-3059 http://www.m2inc.com ©2011 M2 Antenna Systems Incoporated... -
Page 3: Overview
Now we offer the same high performance in VHF amplifiers. The 6M-1K2 and the 2M-1K2 utilize the new Freescale™ LD MOS FET (MRFE6VP6IK25H), a single device specified to produce 1.25 kW with as little as 3 watts of drive from HF to 600 MHz. This is amazing in itself, but adding its inherent stability driving that power into a 65:1 mismatch is equally incredible. -
Page 4: Major Components
OVERVIEW MAJOR COMPONENTS, 2M-1K2 FRONT PANEL 1. +50V LED (Yellow). Indicates +50 VDC is present from the power supply 2. Ready LED (Green). Lights when the Power switch is on and the amplifier is ready to be keyed and driven. -
Page 5: Cover
OVERVIEW REAR PANEL (shown with optional power supply) 9. Key Jack. Ground to transmit. The total keying current is under 10 mA. 10. RF In. 25-50 W nominal. 11. RF Out. It is strongly recommended that an external wattmeter be connected here. Use .405” or larger diameter, 50 ohm coaxial cable capable of handling full rated output power. -
Page 6: Theory Of Operation
OVERVIEW THEORY OF OPERATION The 2M-1K2 designation, indicates the amp works on the 2 meter Amateur Band and is capable of at least 1.25 kW of RF output. A single MRFE6VP61K25H Freescale™ LDMOSFET solid state device is the heart of the amplifier. - Page 7 OVERVIEW voltage also passes through the transformer. The emitter of the device is grounded to its flange base (header) which in turn is attached to the copper heat spreader. There is a common ground then in the system between the chassis, the PC board and the heat sink system.
-
Page 8: Installation
INSTALLATION TYPICAL INSTALLATION M2 ANTENNA WATTMETER XCVR 2M-1K2 Transceiver Power 220 VAC (Nom.) Amplifier 50/60 Hz 15 A Max (Models w/PS) 48-50 VDC @40-50 A INSTALLATION CONSIDERATIONS • WARNING: SAFETY IS ALWAYS A PRIORITY! ALWAYS OBSERVE APPROPRIATE ELECTRICAL SAFETY PRECAUTIONS WHEN INSTALLING AMPLIFIERS AND RELATED EQUIPMENT. -
Page 9: Troubleshooting
3 Amp internal fuse is open. (rare). The unit will continue to operate normally. Internal 13.6 VDC regulator failed. Contact M2 for repair. See "Support, Service and Returns." No TX LED (Red) when the amp is keyed. Key line is not pulled completely to Check the keying circuit by shorting the center conductor of the RCA ground. -
Page 10: Support, Service And Returns
TROUBLESHOOTING Still don’t see what you are looking for? This guide is not all-inclusive, as there is just no way to predict every failure. However, we will be more than happy to provide any assistance we reasonably can. Please see “Support, Service and Returns” below. SUPPORT, SERVICE AND RETURNS If you have followed the provided troubleshooting steps and your product is still not performing as specified, please contact us for further technical support. - Page 11 TROUBLESHOOTING...
-
Page 14: Addendum
ADDENDUM PARTS LIST FOR 2M-1K2 DESCRIPTION ...............QTY 2M-1K2 2M High Power Amplifier ..........1 2M-1K2 Operating Instructions............ 1 RSP-2400-48 power supply Operating instructions (If applicable)... 1 3 Amp Fuse (spare)..............1 Q3 Keying Transistor, ZTX601B (spare) ........1... -
Page 15: Specifications
ADDENDUM SPECIFICATIONS Model ........2M-1K2 Frequency Range ....... 144-148 MHz Power Out ......... 1250 W PEP Drive Input (Max Output) ... 50 W GENERAL SPECIFICATIONS Modes ........SSB, CW, JT65, FM AM Duty Cycle in JT, FM or AM ..40% (45 sec. on, 75 sec. off) Efficiency........ -
Page 16: Wsjt: What Is It And How Do I Get It
ADDENDUM WSJT: What Is It and How Do I Get It? A special EME and weak-signal primer by renowned EME expert Mike Staal, K6MYC. WSJT is a new weak signal mode enhancing communications with signal near or below the audible signal level. The 6M-1K2 amplifier is designed for the 50% duty cycle used in this mode. - Page 17 ADDENDUM WSJT: What Is It and How Do I Get It? (Continued) One last bit of information you will need to get started using EME. Since most signals from the moon are at or below the noise they may not be detectible by the human ear. A chat room has been created to allow you to communicate with others doing EME and find where others are transmitting so you can “listen”...
-
Page 18: Warranty
M2 warrants the 2M-1K2 amplifier against defects in material and workmanship for a period of 12 months from date of purchase. During the warranty period, M2 will, at its option, either repair or replace products or components which prove to be defective. The warranty shall not apply to defects or damage resulting from: •...