Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for ice.net R90 series
-
Page 2: Important Notice
R90 Series Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the router are used in a normal manner with a well-constructed... -
Page 3: Table Of Contents
R90 Series TABLE OF CONTENTS 1 Introduction ......................4 2 Product Overview ....................4 2.1 Placement of your R90 .................. 5 3 Using your Router ....................6 3.1 Package Contents ..................6 3.2 Router Interfaces ..................6 3.3 Power LED ....................6 ... -
Page 4: Introduction
R90 Series Introduction Thank you for purchasing the Ice.net R90 EV-DO router .This user manual will help you setup, configure and outline best practices for maximizing your wireless home network performance with the router. Product Overview In minutes, you will be able to connect your computers to the Internet, share your Internet connection and network your computers.. -
Page 5: Placement Of Your R90
R90 Series 2.1 Placement of your R90 Place your R90, the central connection point of your network, as close as possible to windows or in rooms at the outer side of your house. If you also use the Wi-Fi feature of the R90, it should be placed near the center of your wireless network devices. -
Page 6: Using Your Router
R90 Series Using your Router 3.1 Package Contents • R90 EV-DO Rev B router • Antennas • RJ-45 Ethernet Networking Cable • Power Supply (230V) • Car Charger (12V) • Quick Installation Guide • CD with Complete User Manual 3.2 Router Interfaces The R90 is designed to be placed on a desktop or wall mounted. -
Page 7: Signal Strength Led
R90 Series 3.4 Signal Strength LED This LED indicates the signal strength of the CDMA network serving the router. LED Color Status No CDMA signal Blue Strongest Level Blue Medium Level Blinking(3s) Blue Low Level Blinking(1s) 3.5 Connect LED This LED informs you that the router is connected to a wireless network and that your user ID and password have been validated. -
Page 8: Setting Up Your Hardware
R90 Series 3.9 Setting up your hardware 1 Make sure your router is not connected to any power source and that all the LEDs are OFF. 2 How to setup the antennas for maximized performance ① Antennas are located on both sides of the router. -
Page 9: Web Manager Options
R90 Series Web Manager Options The Web Manager User Interface is a web-based tool that you can use to setup the router. You can also use it to manage advanced functions of your router. From the User Interface, you can perform these tasks: •... - Page 10 R90 Series If another user is already logged into the web interface then you will receive this error message. Please wait until the other person has logged out. 3. After entering the correct user name and password you will be asked if you want to change the user name and password of the web page.
- Page 11 R90 Series 4. Once you click OK the following screen will appear and you can then enter your new User Name and Password. Once you have done this please press the apply button. Your router will reboot and you will need...
-
Page 12: Basic Wireless Settings
R90 Series 4.1 Basic Wireless Settings Clicking on the header of the “Basic Wireless Settings” tab will take you to the “Basic Wireless Settings” page. There are options that allow you to make changes to the Wi-Fi wireless network settings 4.1.1... - Page 13 R90 Series 4.1.2 Selecting the Wireless Channel Your router as default is pre-configured to choose the best wireless channel. It does this by looking at the channels that are being used by Wi-Fi networks and choosing the best channel accordingly. If needed this channel can be changed.
-
Page 14: Router Status
R90 Series Router Status Clicking on the header of the “router Status” tab will take you to the “router Status” header page. From this page you can find all the relevant information pertaining to your router such as firmware version and IP address. -
Page 15: Network Information
R90 Series 4.3 Network Information The network information page will provide all the information and detail with regards to the mobile network. The information on this page can be very useful when you are in contact with Customer Services. -
Page 16: System Settings
R90 Series 4.4 System Settings From the system settings page you can perform a variety of administration tasks. Set Password – From here you can change the password which is used to access the web GUI Set Username – This option allows you to modify the user name which is used to access the web GUI Management Interface Protocol –... -
Page 17: Advanced Wireless Settings
R90 Series Advanced Wireless Settings From this page you can enable / disable your WiFi, as well as decide whether to broadcast your SSID. If you would like to disable access to the web interface via WiFi you can un-check the ‘Enable Access to Router Management via Wi-Fi’... -
Page 18: Multi Port Forwarding
R90 Series 4.6 Multi Port Forwarding Clicking on the “Multi Port Forwarding” sub-heading in the “Advanced” list will take you to the relevant page. Multi Port Forwarding allows you to route a range of ports to the devices that are connected to your router. -
Page 19: Single Port Forwarding
R90 Series 4.7 Single Port Forwarding This feature helps forward IP packets from a specific port to a specific host in your LAN by changing the port number. -
Page 20: Firewall
R90 Series 4.8 Firewall This page will allow you to enable / disable your firewall... -
Page 21: Lan Mac Filtering
R90 Series 4.9 LAN MAC Filtering Your router can be configured to restrict access to the Internet, email or other network services. Restrictions can be set for a single computer, a range of computers or multiple computers. 4.9.1 MAC Filtering The MAC address filter is a powerful security feature that allows you to specify which computers are allowed on your network. -
Page 22: Wan Setup
R90 Series 4.10 WAN Setup Clicking on the “WAN Setup” sub-heading in the “Advanced” list will take you to the “WAN Setup” page. This is where you can enable or disable the router’s DMZ, Internet Ping, and HTTP-related items. 4.10.1 Demilitarized Zone (DMZ) The DMZ feature allows you to specify one computer on your internal network to be placed outside the firewall. - Page 23 R90 Series...
-
Page 24: Lan Ip Setup
R90 Series 4.11 LAN IP Setup Clicking on the header of the “LAN IP Setup” tab will take you to its header page. LAN TCP/IP Setup 4.11.1 The IP address in this instance is referring to the IP address that you use to log into your router (default 192.168.0.1). - Page 25 R90 Series...
- Page 26 R90 Series...
-
Page 27: Dynamic Dns
R90 Series 4.12 Dynamic DNS Dynamic DNS (Domain Name Service) is a method for Dynamic IP users to notify a domain name server to change, in real time (ad-hoc) the active DNS configuration of its configured hostnames, addresses, or other information stored in DNS. -
Page 28: Static Routes
R90 Series 4.13 Static Routes A static IP address connection type is less common than other connection types. If your ISP uses static IP addressing, you will need your IP address, subnet mask and ISP gateway address. This information is available from your ISP or on the paperwork that your ISP gave you. -
Page 29: Upnp Settings
R90 Series 4.14 UPnP Settings From this page you can enable / disable UPnP, Universal Plug and Play. -
Page 30: Cdma Settings
R90 Series 4.15 CDMA Settings Clicking on the header of the “CDMA Settings” tab will take you to its header page. From this page, the router’s basic settings can be modified. These settings include: • PPP Login ID and password (if applicable) •... -
Page 31: Troubleshooting
R90 Series Troubleshooting Problem Solution Please ensure that you are connected to your R90. If you are using Wi-Fi please try to connect via an Ethernet cable to the R90 to see if that resolves the I am unable to connect to the Internet. The R90’s issue. -
Page 32: Technical Specification
R90 Series Technical Specification Size 180 x 160 x 26 mm Weight 500g Battery Type Li-ion (2 cell), 7.4V(Max 8.4V)/1000mA/h Operating Temperature -20o C ~ +60o C Storage Temperature -30o C ~ +70o C Humidity 5 ~ 95% Stand by Time... -
Page 33: Certification
R90 Series Certification...