MD 5008 Owner's Manual
  1. Manuals
  2. Brands
  3. MD Manuals
  4. Metal Detector
  5. 5008
  6. Owner's manual

MD 5008 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
MAIN TECH PARAMETER
MAIN TECH PARAMETER
Emitting Frequency
6.99KHz
Signal Frequency
437KHz
Weight
2.875KG
Power Supply
8pcs 1.5V Batteries
Attach external
battery box and bag.
Max Detection
Small coil: 1.5meters
Big coil: 3.0-3.5meters
This conclusioin is elicited by
testing
an
aluminum
sheet
(60cm*60cm*1cm) buried in
dry soil
Sensitivity
Small coil: 25-30cm (test 25 US
cent)
Big coil: 35-40cm (test 25 US
cent)
15
CARE AND MAINTENANCE
If the detector doesn't work
properly, it is possible that the
batteries haven't enough power,
replace batteries to try ;
Place batteries matching the
polarity symbols (+ and －) If
you won't use it for a long time,
take out the batteries to avoid
putridness;
The search coil's plug should be
not affected with damp, or the
detector will loss detection
ability; the plug can be used
only after drying in such
condition;
The detector is prohibited to
work in rainy day and in
burning sun;
The search coil should be far
away from furnace and other
high temperature circumstance;
Each detector is attached a
piece of guarantee and it is free
to be repaired during the length
of warrantee unless he circuit is
changed by user himself.
OWENER'S MANUAL
Please read before using this equipment

Metal Detector

5008
MD-5008

Advertisement

Table of Contents
loading

Summary of Contents for MD 5008

  • Page 1: Metal Detector

    Emitting Frequency replace batteries to try ; 6.99KHz Place batteries matching the OWENER’S MANUAL MD-5008 polarity symbols (+ and －) If Signal Frequency you won’t use it for a long time, 437KHz take out the batteries to avoid Weight putridness;...
  • Page 2 FEATURES With your MD-5008 Metal TREASURE HUNTER’S CODE OF Notes: Detector, you can hunt for coins, ETHICS The search coil will not 3. While holding the search relics, jewelry, gold, and silver, etc, detect without motion. You coil level and about 8 inches just about anywhere.

  • Page 3: Table Of Contents

    DETECTION NOTES CONTENTS 6) Eliminate unneeded target: INDOOR TESTING AND Preparation ....................3 Assembling the Detector…………………………………………………3 If detect indoor or search very Installing Batteries……………………………………………………….4 trashy ground, there are a lot of 1. Remove any watches, ring, or Testing the Batteries…………………………………………..5 metal trash, they are usual no use other metal jewelry you are Adjusting the Meter………………………………………………5 and can be eliminated during the...

  • Page 4: Preparation

    PREPARATION ASSEMBLING THE DETECTOR bracket and the stem. Push the Remove any watch, ring, metal 4) Set “GROUND BALANCE” as connector through the holes and button, cigarette box, etc you are mentioned above; Assembling your detector is easy tighten the knob wearing, and wear shoes without 5) Sweep the search slowly along and requires no special tools.

  • Page 5: Installing Batteries

    ACTUAL OPERATION To disconnect the search OPERATION MODE SWITCH PREPARATION: 1. If the detector is ON, turn it to (MODE) coil’s cable from OFF. Place batteries into the battery detector, grasp the plug and compartment, turn on the power There are two sections in operation pull it out of the connector.

  • Page 6: Testing The Batteries

    5. Press left battery When rotate compartment cover’s tab and TESTING THE BATTERIS detector eliminates “DISCRIMINATION” to different slide the cover off in the “mineralization reaction” signal position, distinguish direction of the arrow. If the indicator light is dim or after setting “Ground Balance”...

  • Page 7: Listening Safely

    Lower the search coil about To connect headphones to the 8inch above the ground; if detector, insert the headphones’ Once you set the volume, do the volume rises, raise the 1/8 inch plug into the headphone not increase it. Over time, your search coil (about 24inch) jack on the side of the control ears adapt to the volume level,...

  • Page 8: Introduction Of Operating Buttons

    INTRODUCTION OF OPERATION BUTTON ZEROING BUTTON During detection , with the Note: example, those heavy changes of environment, Press the Zeroing Button mineralization area, high sensitivity Zeroing Button is at the forefinger’s pointer often leaves “0” before adjusting the “critical causes false signal, the detector position when holding the detector.

Table of Contents