Advertisement
Quick Links
For the following Model:
38A00-2 HAI UPB™ 8-Button House Controller
READ THESE INSTRUCTIONS BEFORE INSTALLING DEVICE
This HAI UPB™ 8-Button House Controller is intended for installation in accordance with the National Electrical Code and local
regulations. It is recommended that a qualified electrician perform this installation. Retain these instructions for reference.
This product is for indoor use only. Connect only copper or copper clad wire to this device.
Important Notes Prior To Installation
Be sure that all power to the load has been disconnected by turning off the circuit breaker. Installing an HAI UPB™ 8-Button House
Controller with power on may expose you to dangerous voltage and may damage the device.
HAI UPB™ 8-Button House Controller Overview
The HAI UPB™ 8-Button House Controller (Figure 1) is used to turn on or off lighting in up to 8 rooms in a house where HAI
UPB™ Wall Switches and HAI UPB™ 6-Button Room Controllers have been installed. It can also be used for various other lighting
control applications, such as controlling 8 individual loads or lighting scenes (on/off). It uses the UPB™ two-way powerline
communication technology to communicate with an HAI controller, UPB™ Wall Switches, and other UPB™ devices on the network.
The HAI UPB™ 8-Button House Controller has eight pushbuttons labeled 1, 2, 3, 4, 5, 6, 7, and 8 (although these buttons may be
custom engraved). Each pushbutton is slightly backlit so that the buttons can be seen in a dark room. Depending on configuration of
the HAI UPB™ 8-Button House Controller, one or more of the eight pushbuttons will be distinctly illuminated, indicating that one or
more lights are on in the respective room(s). If a pushbutton is not illuminated, that means all lights in the respective room are
currently off.
1
2
3
4
5
6
7
8
Figure 1 - HAI UPB™
8-Button House Controller
HAI UPB™ 8-Button House Controller
Installation and Operating Instructions
Changing Switch Color
The color of the HAI UPB™ 8-Button House
Controller may be changed to complement the
interior décor.
The HAI UPB™ 8-Button
House Controller is supplied with a white
bezel. Additional colors are available; contact
your HAI distributor for more information.
When changing the bezel, make sure that the
HAI UPB™ 8-Button House Controller is
disconnected from all power, and proceed as
follows:
1. The bezel attaches to the HAI UPB™
8-Button House Controller with two small
Philips head screws: one on the upper-
right corner and one on the lower-left
corner (Figure 2).
2. Using a small-bladed Philips screwdriver, unscrew each of the two screws.
bezel from the back housing.
3. Install the new bezel by aligning the mounting holes on the bezel with the installation pins
on the back housing. Secure bezel to back housing with the two Phillips screws that were
removed in Step 1.
Figure 2 – Changing Switch Color
Remove the
38I00-2, Rev B
Advertisement
Related Manuals for HAI 38A00-2 UPB
Summary of Contents for HAI 38A00-2 UPB
- Page 1 HAI UPB™ 8-Button House Controller Overview The HAI UPB™ 8-Button House Controller (Figure 1) is used to turn on or off lighting in up to 8 rooms in a house where HAI UPB™ Wall Switches and HAI UPB™ 6-Button Room Controllers have been installed. It can also be used for various other lighting control applications, such as controlling 8 individual loads or lighting scenes (on/off).
- Page 2 4. After all connections have been made, be certain that all wire connectors are firmly attached and there is no exposed copper. 5. Gently place the wires and HAI UPB™ 8-Button House Controller into the wall box with the “1” pushbutton at the top of device.
- Page 3 Tap the Decora-style rocker switch on the HAI UPB™ Wall Switch Dimmer(s) five (5) times quickly. The HAI UPB™ Wall Switch Dimmer will flash its lighting load one time and blink its LED blue, to indicate that it is ready to be linked.
- Page 4 HAI warrants this product against defects in material and workmanship, under normal use and service, for a period of two (2) years from the date of purchase. During the warranty period, HAI will repair or replace, at its sole option, if this product fails due to defect. This warranty does not cover the cost of removal or reinstallation of any product.