Napoleon F40 Installation And Operation Instructions Manual

Included with the F40 Universal Remote:
QTY. PART# DESCRIPTION
1 W660-0066 Transmitter
2 N043-0002 "AAA" Batteries
1 W080-0930 Wall Mount Cradle
1 W660-0076 Receiver
1 W500-0405 Wall Faceplate
1 W500-0404 Fireplace Mounting Plate
1 W660-0080 Slide Switch
4 W043-0002 "AA" Batteries
1. RECEIVER INSTALLATION
The receiver (W660-0076) can be installed as either a wall mount
applicable steps below after having completed step 1.1.
Turn off the electrical power and the gas supply to the appliance. Make sure the slide switch on the receiver is set to the "OFF" position.
1.1 Either disconnect the existing switch wiring at the valve, or connect in parallel*
with any other switch wiring at the valve. For millivolt switch wiring attach the wires
to terminal 1 (marked TPTH) and terminal 3 (marked TH) of the gas valve from the
output terminals on the receiver. FIGURE 1 Note: If connecting the receiver to an
appliance with electronic ignition, connect the receiver wires to the two leads
from the control module, identifi ed as switch wires. (It may be necessary to
remove the spade connectors and join the wires using wire connectors)
*INSTALLER: It may be advisable to connect a backup switch. This will allow the
homeowner to continue to control the burner in the event of battery failure.
A RECEIVER WALL MOUNT
1.2 Press the battery compartment slightly into the receiver and
release enabling the battery compartment to pop out. Pull off the slide
switch. Slide the receiver out of the wall mounting plate. FIGURE 2
1.3 Using the screws provided secure the receiver and the wall face
plate to an existing junction box. FIGURE 2
1.4 Replace the black slide switch with the white one included to match
the cover plate. Place 4 AA batteries into the battery compartment and
slide the compartment back into the receiver. FIGURE 3
1.5 Turn on the electrical power and the gas supply to the appliance.
WALL MOUNT
INSTALLATION
SLIDE
BA T.L OW
SWITCH
FIGURE 2
WALL FACEPLATE
BATTERY
INSTALLATION
STICKER
(See 7. FINISHING)
COMPARTMENT
FIGURE 3
F40, F50 AND F50D UNIVERSAL REMOTE
INSTALLATION AND OPERATION
INSTRUCTIONS
Included with the F50 Universal Remote:
QTY. PART#
1 W660-0067
2 N043-0002
1 W080-0930
1 W660-0076
1 W500-0405
1 W500-0404
1 W660-0080
4 W043-0002
**FOR OTHER AVAILABLE COLOURS, ADD THESE LETTERS TO THE BASE PART NUMBER:
JUNCTION
BOX
RECEIVER
BA T.L OW
BATTERY
DESCRIPTION
Transmitter
"AAA" Batteries
Wall Mount Cradle
Receiver
Wall Faceplate
Fireplace Mounting Plate
Slide Switch
"AA" Batteries
A B
or a appliance mount
RECEIVER
FIGURE 1
B RECEIVER APPLIANCE MOUNT
For stove and insert models: Do not install the receiver in the gas control
valve compartment in some models as this area becomes too hot. On
stoves, it may be installed in or behind the pedestal; on inserts, it may be
installed behind the fl ashings or a similar convenient location.
In a zero clearance model: The receiver may be installed in the gas control
compartment located below the fi rebox.
1.2 Ensuring that the mounting location will allow for the battery
compartment to pop out, secure the receiver to an appropriate location
depending on the appliance model using the adhesive pad located on the
bottom of the appliance mounting plate.
1.3 Turn on the electrical power and the gas supply to the appliance.
APPLIANCE MOUNT
INSTALLATION
RECEIVER
APPLIANCE
MOUNTING PLATE
FIGURE 4
BATTERY
INSTALLATION
STICKER
(See 7. FINISHING)
Included with the F50D Universal Remote:
QTY. PART# DESCRIPTION
1 **W660-0087 Transmitter
2 N043-0002 "AAA" Batteries
1 **W080-1050 Wall Mount Cradle
1 W660-0076 Receiver
1 W500-0405 Wall Faceplate
1 W500-0404 Fireplace Mounting Plate
1 W660-0080 Slide Switch
4 W043-0002 "AA" Batteries
COLOUR
BLACK
GREY
. Depending on your application, follow the
ADHESIVE
PAD
OF F
RE MO
TE ON
SLIDE
SWITCH
BATTERY
COMPARTMENT
FIGURE 5
LETTER
K
Y
RED R
1
GAS VALVE
3