1. Manuals
  2. Brands
  3. Command Communications Manuals
  4. Microphone
  5. PrivatePage PS2000AN
  6. Operator's manual

Command Communications PrivatePage PS2000AN Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PrivatePage PS2000AN and is the answer not in the manual?

Questions and answers

Related Manuals for Command Communications PrivatePage PS2000AN

Summary of Contents for Command Communications PrivatePage PS2000AN

  • Page 2: Table Of Contents

    Introduction to the PS2000AN.............… Unpacking the PS2000AN..............…. Installing the PS2000AN............…..……. 2 - 4 Positioning the PS2000AN..........…..… 2, 3 Connecting power to the PS2000AN........…….. Installing/replacing pager batteries..........….… Using the PS2000AN……………………..........… 4 - 6 Overview………………................… Storing the system code………............… Storing the pager code................…...

  • Page 3: Important Notes

    (An outdoor antenna can be purchased at a The PS2000AN can send 10 different message codes consumer electronics store.) (0-9), and address up to 1,000 individual (system) pagers. Please read through the rest of this guide to learn how to properly install and operate the PS2000AN.

  • Page 4: Unpacking The Ps2000An

    PS2000AN Operator’s Guide Unpacking the PS2000AN When you open the PS2000AN box for the first time, inspect the contents. In the box, you should find the following items: If any of these items are missing or damaged, contact the dealer where you purchased the unit, or call Customer Service at the number listed in "Service Information."...

  • Page 5: Connecting Power To The Ps2000An

    Installing/replacing pager batteries The PS2000AN works with both VM200 (vibrating), VP200 (vibrating) and VP201 (tone or vibrating) system pagers (not included). The individual pagers are powered by two (2) AAA batteries (not supplied). We recommend that you use alkaline batteries to power the pagers.

  • Page 6: Using The Ps2000An

    PS2000AN Operator’s Guide Using the PS2000AN In this section, there are operating notes for using the PS2000AN. Read these notes before attempting to operate the system. Overview Before operating the PS2000AN, be sure that you understand the following information concerning the paging system's capabilities.

  • Page 7: Storing The Pager Code

    PS2000AN Operator’s Guide Storing the pager code Before you can use the pagers with the PS2000AN, you must designate a pager code for each of the pagers. NOTE: You must reset all pager codes when you enter a new system code.

  • Page 8: Transmitting A Message Code To A Group Of

    PS2000AN Operator’s Guide Transmitting a message code to groups of pagers 1. Turn the PS2000AN power ON. Or, press (then message code) - 0 GROUP GROUP sets message code for all pagers numbered 000 through 2. Press the CANCEL button if the display shows 099.

  • Page 9: Alarm Notification Paging

    Connect to jack PS2000AN When either contact is momentarily closed and then opened (in the case of a doorbell trigger), the PS2000AN will automatically page the pre-assigned pager. Storing the pager assignment: Contact 1 memory position: Contact 2 memory position: 1.

  • Page 10: Contact Paging Priority Sequence

    PS2000AN Operator’s Guide Contact priority paging sequence When the PS2000AN is in a normal paging cycle (the it will ignore Contact 2 and continue to page the pagers base unit is transmitting a signal to a pager) and either assigned to Contact 1.

  • Page 11: Reviewing Stored Message Codes

    1. Adjust or reposition the antenna to obtain optimum transmitting range. Connect a base station antenna to substantially increase the PS2000AN's transmitting range. What can I do to reduce the interference on my phone when using the PS2000AN? 1. Adjust or reposition the antenna and the antenna ground wire.

  • Page 12: One Year Limited Warranty/Service Information

    2. Enclose a copy of the bill of sale or other documentation showing original purchase date. 3. Contact the dealer where you purchased the PS2000AN, or call the service center listed below to obtain a return material authorization number (RMA #).

  • Page 13: International Return Policy

    PS2000AN Operator’s Guide International return policy Command Communications, Inc. does not guarantee that this product will be compatible with the telecommunications systems of all countries. Modifications may have been made to the product in order to function in certain locations. Therefore, it is best to purchase our products in the country in which it will be used.
  • Page 14 PS2000AN Operator’s Guide www.commandcommunications.com © 2008 Command Communications, Inc. All rights reserved. Printed in China COMMAND COMMUNICATIONS, PRIVATEPAGE, and the Arrow logo are registered trademarks of Command Communications, Inc., Centennial, CO 80112 14510 E. Fremont Avenue Centennial, CO 80112 email: techsupport@commandcommunications.com...
  • Page 15 AC062402 kr MN080...

Table of Contents