Subscribe to Our Youtube Channel
Related Manuals for Staber Industries System 2000 HXW2901
Summary of Contents for Staber Industries System 2000 HXW2901
- Page 2 4800 Homer Ohio Lane Groveport, Ohio 43125 614.836.5995 phone www.staber.com Product information and specifications are shown herein as of the time of printing. Staber Industries, Inc. reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligation.
- Page 3 SYSTEM 2000 CLOTHES WASHER HXW2901 HXW2921 Operator’s Manual Installation/Operation/Maintenance/Parts Part Number 818235 Printed in USA...
- Page 4 FORWARD We are pleased that you have selected a Staber System 2000 Clothes Washer as one of your appliances. Your clothes will be washed using a tumble action inner tub. Please register your new System 2000 on our Internet web site, www.staber.com.
- Page 5 PARTS...
- Page 6 PARTS ITEM PART NUMBER DESCRIPTION QUANTITY 817271 Cabinet 817115 Front Panel 818217 Screw 817291 Locking Pin 817289 817103 Inner Tub Assembly 817107 Drive Shaft Assembly 818201 Bolt 1/4-20 x 5/8 S.S. 817109 Support Shaft Assembly 813221 Power Cord 817279 817314 Control Panel - HXW2901, 2921 818241 Screw...
-
Page 7: Important Safety Instructions
PRODUCT IDENTIFICATION Model, Series and Serial numbers are used to identify your new Staber System 2000 Clothes Washer. These numbers should always be referred to when consulting the Customer Assistance Center concerning service, parts, or other information you may require. For your convenience and ready reference, enter Model, Series, and Serial numbers below. - Page 8 STABER INDUSTRIES DOES NOT ASSUME ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion may not apply to you.
- Page 9 PARTS FRONT VIEW REAR VIEW 19 18 25 23 42 41 LOWER VIEW BASE...
- Page 10 PARTS ITEM PART NUMBER DESCRIPTION QUANTITY 813217 Motor 818225 Flat Washer 5/16 818265 Lock Washer 5/16 818229 Bolt 5/16-18 x 3/4 817216 Shaft, Motor Pivot 818223 Fiber Washer 818219 Retaining Ring 817219 Weight - Side 817305 Bracket 818261 Bolt 5/16-18 x 4 818225 Flat Washer 5/16 818265...
- Page 11 INSTALLATION CAUTION: Use great care when loading, unloading or working around clothes basket with top lid raised. DO NOT allow any items to fall between inner and outer tubs. If this should occur DO NOT START WASHER. The item must be removed from the tub or damage to the clothes basket or water system may occur.
- Page 12 BENEFITS OF SYSTEM 2000 Washes more clothes per load than a traditional agitator washer and saves on drying time with superior moisture extraction. 2. Gentle wash action ensures less wear and tear on clothes (clothes last longer). 3. Conserves water, energy, and money spent on laundry products. TO WASH CLOTHES, FOLLOW THESE SIMPLE INSTRUCTIONS: STEP 1 After raising top outer lid, open access doors to clothes basket.
- Page 13 PARTS ITEM PART NUMBER DESCRIPTION QUANTITY 813261M Wiring Harness - HXW2901, 2921 813219 Motor Controller 813203 Lid Lock 814201 Pump 814203 Water Valve 813215 Pressure Switch 813209 Switch - Temperature 813211 Switch - Wash Cycle 813213 Indicator Light - Red 813214 Indicator Light - Green 813245...
-
Page 14: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE CORRECTIVE ACTION Washer agitates continuously. Motor control circuit board has failed. Replace board. Water does not drain from clothes washer. Obstruction in sump area of outer tub. Remove obstruction. Obstruction in sump hose. Remove obstruction. Obstruction in pump. Remove pump and clear obstruction. - Page 15 FOUR THINGS THAT AFFECT THE CLEANLINESS OF YOUR CLOTHES 1. The amount of Agitation: Equipped with a patented inner and outer tub, the Staber System 2000 is designed to increase the agitation rate allowing for minimal use of chemicals, heat and time per wash load. 2.
- Page 16 OPERATION COINS TEMPERATURE 2000 WASH CYCLE YSTEM Power Power Warm Cold Normal Perm Delicate TO START PLEASE SEE UNDERSIDE OF LID KNOBS Lid Locked FOR OPERATING INSTRUCTIONS Notes: To Stop Washer Press The Stop Stop Switch To The STOP Position. When Lid Locked DEPOSIT Light Extinguishes, Then Stop Switch...
- Page 17 TROUBLESHOOTING PROBLEM CAUSE CORRECTIVE ACTION Lid locked light does not illuminate within Lid is not fully closed. Close lid completely. 14 seconds after coins have been inserted. Microprocessor did not properly boot up. Reseat microprocessor, unplug machine for a minimum of 30 seconds and plug back in. Lid lock assembly has failed.
- Page 18 Secure the top with two 5/16 headed screws. 14 Reinstall front panel as directed under "INSTALL FRONT PANEL" and plug power cord into electrical receptacle. 15 Return old board to Staber Industries, Inc. via U.S. Parcel Post with no insurance within one week REPLACE PRESSURE SWITCH Disconnect the appliance from the power source.
- Page 19 TO WASH CLOTHES Caution – IMPORTANT Use only recommended amount of liquid detergent, bleach or fabric softener. Using more detergent than recommended decreases cleaning effectiveness, can cause suds or water to overflow and damage drive motor, voiding your warranty. Raise top lid. Open access doors to clothes basket.
- Page 20 REPLACE DRIVE BELT Remove the front panel as directed under "REMOVE FRONT PANEL". Remove belt and inspect pulleys for wear and tightness. Install new belt on pulleys, check belt tension and adjust as necessary. Install front panel on clothes washer as directed under "INSTALL FRONT PANEL"...
- Page 21 REPLACE TEMPERATURE AND WASH CYCLE SWITCHES Disconnect the appliance from the power source. Remove the six screws that hold the control panel to the top. Allow the control panel to slide down, pull the top of the control panel out and lift up. Lay the control panel face down on the top.
Need help?
Do you have a question about the System 2000 HXW2901 and is the answer not in the manual?
Questions and answers