Page 2
Preface Thank you very much for purchasing „NECO‟ brand motorcycle of model NECO F2, which developed by NECO MOTORCYCLE. And welcome to join the driver‟s line of NECO motorcycle. With its extraordinary advantages of excellent quality, smart appearance and shape of legerity, our product will surely bring the utmost pleasure and convenience to your life.
□Guidance Please keep safety in your mind and observe the regulations of transportation while enjoying your riding. Pay attention to the following rules: 1. Pre-riding inspection Please read the details in the relevant chapter for your safety. 2. Helmet Do remember to wear helmet while riding. Warning 3.
Page 5
Positions of the numbers The frame number and the engine number are for the purpose of registering the motorcycle. When your motorcycle needs inspection, repair or other special service, the number will enable you to get good service from our sale agency. Please note down your number here: □...
□ Controlling parts Left turning light 1. Rear brake lever Right turning light Hold it tightly and the rear brake works. C. Horn button 3. Meters and indicating lights 2. Switches on the left A. Engine oil warning light B. Left turning light indicator C.
Page 8
5. Switches on the right I. Key “MODE”. Under the normal mode, shortly pressing the key “Mode” to switch over the mode CLOCK set, shortly pressing“Mode”once to add “1”. J. Key “Light”. Shortly pressing the key “Light” can adjust the state of the back light K.
Warning ON: Engine can be started and all the lights can be operated. The key cannot be taken out. ◆Turn off the engine when refilling the tank. OFF: The whole circuit is cut. Engine and lights cannot ◆Turn off the cap slowly. be operated and the key can be taken out.
□Pre-riding inspection Please check the following parts before you drive. Items Inspection content Steering handlebar 1.Flexibility 2.No gap or loosing appearance 1.Travel of the front brake and the rear brake 2.No break on the cable Brake system 3.Flexible function Tires 1.Proper pressure 2.No crack or cutting Fuel...
□Engine starting 1. Please check the volume of engine oil and gasoline 3. Engine Starting before starting. The main stand and the side stand should be taken back while starting the engine. Grip the brake lever and press the starting button and 2.
Warning Warning ◆ 5 seconds is the maximum limit for each starting ◆ After the engine started, the starting pedal and10 seconds is the minimum interval. should be taken back to its original position. ◆ Stop pressing the starting button immediately Otherwise, it will affect the driver‟s safety.
□ Regular maintenance Interval 1000 3000 6000 12000 Item Month New motor Battery Engine oil strainer Gasoline strainer Carburetor Air cleaner core Clean it every 2000km and replace it when necessary Spark plug Clean it every 3000km and replace when necessary Fuel throttle Drive belt Engine oil...
Page 14
1. Battery Warning 12V/5.7Ah battery ① When the voltage is less than 11.5V, please use ◆ It has been fully adjusted to the highest kick starting in stead of electric starting. position when manufactured. ② Put the ignition switch on OFF position before battery replacement.
Page 15
② Press the core to squeeze the detergent out of it by 5. Fuel palms. Never twist it in case that it is broken. Refill the recommended 90# or higher quality ③ Immerse the core into engine oil. lead-free gasoline when the indicating needle in the ④...
Page 16
① Use the key to open the battery box cover. ②The rear brake (disk brake) ② Open the engine oil tank cover. ③ Fill 0.8L recommended engine oil or much better quality to the engine oil deposited. ④ Close the engine oil tank cover and then lock the battery box cover.
Page 17
◆Brake oil level ☆ Disk brake ◆Grip the brake lever and check the wear and tear ① It has been filled with the special brake oil before the indicator. If the indicator nearly touched the brake disc, motorcycle leaves the factory. User should fill or replace please ask the appointed maintainer to change the brake the qualified brake oil (such as No.DOT3 or DOT4 brake blocks.
Page 18
8. Tires 9. Starting motor Insufficient tire pressure hastens wear of them and Check the fastening bolts and the carbon brush, affects the riding stability. Please check the tire pressure and replace them if necessary. and tread depth when applying regular maintenance. ①Tire pressure: front 250kPa, rear 250kPa.
How to change gear oil □Tools A full set of tools is offered for your daily use Stand up the main stand. Take off the oil plug for refill. Take off the oil plug for draining, let off all the dirty ...
Page 21
Items Specifications Model 1E40QMA Type 2 stroke Cylinder Bore and stroke 40mm×39.2mm Cylinder volume 49cm 7.5 0.1 : 1 Compression ratio Engine Maximum net power output 3.3kw /6500 min-1 Net maximum torque 5.0N.m at 6000 min-1 Carburetor PZ19 Air cleaner Sponge core Ignition type Starting mode...