Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for SAFERA Siro
- Page 1 InstallatIon manual SAFERA Siro Stove Guard with Power Control Unit PCU3 v4.2.1 EnG sIro PCu3...
- Page 2 2. Installation using or installing the appliance. 3. troubleshooting Install and check the application accord- ing to the instructions. SAFERA is not li- 4. optional: Installing the Water leakage able for any damages or expenses caused sensor by inappropriate installation.
- Page 3 1. PrEParatIons Check the product and the contents of the package before installation: • Central unit Ⓐ (pre-installed into a cooker hood) • Power supply Ⓓ Ⓓ • Power Control unit Ⓒ • user and Installation Guides • Declaration of Conformity Ⓐ...
- Page 4 • Induction cookers and hobs ❽ Indicator light panels • Cookers and hobs equipped with a ❾ sensor timer, afterheat indicator, child proof lock or integrated switch-off system saFEra siro is compatible with cookers no wider than 90 cm, see Installation step 1/6.
- Page 5 InstallatIon - step 1/6 mount the Central unit Install the cooker hood with Central unit Ⓐ according to the dimensions: Cooker Installation Width width Height align the Central unit ±15 mm with the cen- max. 60 cm 45 - 75 cm tre of the cooktop.
- Page 6 InstallatIon - step 2/6 mount the Power Control unit Ⓒ. Install the Power Control unit PCu3. 230V 16A 400V 10A 230V 16A 400V 10A 230V 16A 400V 10A MICRO DISCONNECTION ѥ WARNING ⚐ ATTENTION Make sure that there is no power supply Power Control Unit requires a neutral to the cooker and the oven by removing wire to operate.
- Page 7 Installation mount the Power Control unit on the wall behind the cooker or into the cabinet next to the cooker. Couple the protective earth first (PE). Couple the other wires. Don’t reconnect the power to the cooker yet. 130 mm 180 mm 60 mm 5 x 2,5 mm 0,7 m optional water sen- sor connection.
- Page 8 InstallatIon - step 3/6 set up the wireless connection Connect the power supply Ⓓ: indicator light panels ❽ are lit in purple. Press adjustment mode button ❼: indica- tor light panels ❽ start blinking purple-blue. Put back the fuses for the cooker and the oven.
- Page 9 InstallatIon - step 4/6 Calibrate the system When the indicator light panels ❽ start blinking yellow-green, you need to calibrate the system. Choose from the two options: OpTION 1: OpTION 2: Cooker and oven are connected to Only cooktop is connected to the Power Control unit Ⓒ.
- Page 10 InstallatIon - step 5/6 adjust the alarm limit Check the closest recom- location of the Installation alarm limit mended alarm limit from Cooker Height (1-12) the reference table on the right. In a corner 75 cm the range is 1-12: 65 cm 1 = reacts fastest 55 cm...
- Page 11 When you adjust the alarm Color of the indica- number of alarm limit limit, the new alarm limit is tor light panels ❽ beeps indicated as shown in the table ••• ••• on the right. ••• •• ѧ HINT ••• • You may check the alarm limit •••...
- Page 12 InstallatIon - step 6/6 ReaDY! Check-list Check the working order of the appliance and fill in the installation checklist: ፌ all the burners of the cooker cause a child proof lock alarm. ፌ the oven (if connected) causes the child proof lock alarm. the sound signal is lower than the signal from the cooker child proof lock. ፌ...
- Page 13 3. InstallatIon trouBlEshootInG problem Remedy Installation is not proceeding as You can re-start the installation process anytime by pressing the adjustment mode button ❼ for five expected. seconds until you hear the signal and continue from step 3/6. the central unit Ⓐ is not respond- Ensure that the power supply Ⓓ...
- Page 14 4. InstallInG thE WatEr lEaKaGE sEnsor (optional) stove Guard can be equipped with max. four saFEra Water leakage sensors. the sensors are placed in the typical leakage areas, e.g. under the dishwasher or sink. attach the sensors Ⓕ in place.
Need help?
Do you have a question about the Siro and is the answer not in the manual?
Questions and answers