Advertisement
E3NF0BD_QSG_EN.fm Page 2 Wednesday, May 21, 2008 6:08 PM
Connecting to a TV with an HDMI Compatible Port (for HDD, DVD or Tuner)
[HDMI CONNECTION]
A simple 1-cable connection with a device having an HDMI (high-definition multimedia interface) connector allows digital transfer of both digital video signals
and multi-channel audio signals. This is the best method to connect this unit. It can minimise the deterioration of image quality.
Use the HDMI cable (commercially available) for connection.
Connect the HDMI output jack of this unit to the HDMI input jack of TV.
HDMI cable (not supplied)
To HDMI
input jack
HDMI IN
HDMI OUT
this unit
TV
Note for progressive scan:
• Only component and HDMI connections are compatible with the progressive scan.
Connecting to an External Equipment
This unit has three input terminals, AV1(TV) or AV2(DECODER) on the rear panel and AV3 on the front panel. Be sure that all the units are switched off
before making connections.
AV output jack
(Scart)
Scart cable
(not supplied)
Recording from a DVD player, VCR, Satellite
Box or other Audio-Video equipment with a
Scart output jack (AV2)
AV2 (DECODER)
HDMI OUT
Note
• When you record a TV programme from a Satellite Box, you must
connect a Scart cable to AV2(DECODER). (See pages 40 - 41 on the
Owner's Manual for details.)
• When AV2 is connected, the signal from the AV2 will be output
automatically. If you want to monitor the signal from other input, you
must press [DISPLAY] first. Then, select the desired input to monitor
with [INPUT SELECT].
Digital Audio for Better Sound Quality (for HDD, DVD or Tuner)
Dolby Digital decoder or MPEG
decoder, etc.
COAXIAL
After You Have Completed Connections
Switch the input selector on your TV to an appropriate external input channel. For details, refer to the Owner's Manual of your TV.
WARNING!
DO NOT change connections while power is on.
Before installation, unplug your TV and this unit.
EN
Selecting HDMI mode
Press [HDMI] to select the HDMI output mode. The output mode
changes as follows every time [HDMI] is pressed. 576p (PAL) / 480p
(NTSC)
720p
1080i
1080p (An HDMI mode that is not
supported by the display device will be skipped.)
Recording from a camcorder or other Audio-Video equipment with
no Scart output jack (AV3)
Change the setup when using S-VIDEO input jack. (See page 37 on the
Owner's Manual for details.)
AV3 (Front)
S-Video cable
Video cable
Audio cable
(not supplied)
(not supplied)
(not supplied)
S-VIDEO
VIDEO
AUDIO
OUT
OUT
OUT
For clear digital sound quality, use the
COAXIAL
Digital audio
DIGITAL AUDIO OUT (COAXIAL) jack
input jack
to connect your digital audio
equipment.
If the audio format of the digital output
Coaxial cable
does not match the capabilities of your
(not supplied)
receiver, the receiver will produce a
strong, distorted sound or no sound at
all.
Initial Setups
For the First Time Use
1
After making all the necessary connections, turn
on the TV. Select the appropriate external input
channel.
(See pages 17 to 19 on the Owner's Manual for
details.)
2
Press [STANDBY-ON ].
3
Select your desired channel preset type using
U
D
[
/
]. Then press [ENTER/OK].
ENTER
/OK
4
After finishing channel setting, "Clock Setting"
will appear.
• The current date and time will appear automatically.
RETURN
/BACK
• If the current date and time are correct, press
[RETURN/BACK] to exit.
• If you want to adjust the current date and time, press
ENTER
[ENTER/OK] and follow to step 5 in "Manual Clock Setting"
/OK
on page 29 on the Owner's Manual.
HDD/DVD Recording
Basic Recording
If you are recording to the HDD, press [HDD] first.
If your are recording to a disc, press [DVD] first, then insert a
recordable disc.
1
Turn on the TV. Select the appropriate external
input channel.
REC SPEED
2
Select a recording mode using [REC SPEED].
(See page 30 on the Owner's Manual for details.)
INPUT
SELECT
3
Press [INPUT SELECT] to select DVB, analogue or
external input mode, then select the desired
channel to record using [PROG.
/
] or [the
Number buttons].
PROG.
4
Press [REC] to start recording.
The "I HDD" or "I DVD" mark will be displayed on the TV
REC
screen briefly.
To pause the recording, press [PAUSE p].
Press [REC] or [PAUSE p] to resume the recording.
STOP
5
Press [STOP S] to stop the recording.
Note
• Recording continues until the disc is full (as for HDD, 12 hours after
the recording starts) or you stop the recording.
• If the clock is not set, the date and time of title names will be 01/01/08
and 00:00.
• You cannot change the recording speed in the REC or REC pause
mode.
• Even if the broadcasting you are recording is in the SECAM system,
this unit automatically converts it to the PAL system when recording.
• If the external equipment is connected to AV2, the picture of the
external equipment will be output except during the DVD playback of
this unit. Turn off the external equipment or press [DISPLAY] to output
the picture of this unit.
• You can play back a title on one component while making a recording
on the other component. To do so, simply select the component (HDD
or DVD) you want to use for the playback by pressing [HDD] or [DVD]
during HDD / DVD recording. And then follow the normal playback
procedure.
• If playback and recording are in progress at the same time, select the
appropriate component by pressing [HDD] or [DVD] before you press
[PAUSE p] or [STOP S] to pause or stop the operation.
• Up to 600 titles can be recorded on the HDD.
• Up to 99 titles can be recorded on the DVD-RW/-R discs.
• NTSC recording is prohibited in this unit.
Channel Setting
Programme the tuner for both analogue and DVB channels you can
receive in your area.
SETUP
1
In stop mode, press [SETUP].
2
Select "General Setting" using [U / D], then
press [ENTER/OK].
3
Select "Channel" using [U / D], then press
[ENTER/OK].
4
Select "Auto Tuning (DVB & ANALOG)" using
ENTER
[U / D], then press [ENTER/OK].
/OK
The unit will start storing channels available in your area.
Wait for several minutes to finish channel storing.
5
SETUP
Press [SETUP] to exit.
After Auto Tuning has stopped:
Use [PROG.
/
] or [the Number buttons] to change the
channel.
You can select the channels memorised only in
this unit by using
[PROG.
/
].
• You can also tune the analogue or DVB channels
individually. (See pages 21 to 22 on the Owner's Manual.)
• You can also tune the channels manually. (See pages 21 to
23 on the Owner's Manual.)
HDD / DVD Basic Dubbing
Bi-directional Dubbing between HDD and DVD
Insert a recordable disc when dubbing from HDD to DVD.
Insert a disc to be dubbed when dubbing from DVD to HDD.
SETUP
1
In stop mode, press [SETUP].
2
U
D
Select "Dubbing" using [
/
], then press
[ENTER/OK].
3
HDD
DVD
U
D
Select "HDD
DVD" using [
/
], then press
[ENTER/OK].
ENTER
DVD
HDD
/OK
U
D
Select "DVD
HDD" using [
/
], then press
[ENTER/OK].
4
U
D
Select "Add" using [
/
], then press
[ENTER/OK].
5
Select a desired title using [U / D / L / P], then
press [ENTER/OK].
6
Repeat steps 4 to 5 until you register all the titles
to be dubbed.
7
After adding all the titles you want, select
"Dubbing Start" in the dubbing menu using
U
D
[
/
], then press [ENTER/OK].
ENTER
/OK
8
Select a desired recording speed using [L / P],
then press [ENTER/OK].
9
U
D
Select "Yes" using [
/
], then press
[ENTER/OK].
• Dubbing will start.
STOP
To stop dubbing in progress:
Press [STOP S] on the front panel.
Press [STOP S] for 2 seconds on the remote control.
EN
Advertisement
