Sears Brands Management Corporation Hoffman Estates, IL 60179 U.S.A. www.kenmorewater.com www.kenmore.com www.sears.com Sy;tem tested and certif ed by NSIF nternational IEste s sterna ha sdo probado por NSF Internat onal de acuerdo Agua against II",,,,ISIF/ANSStandard for ha dness reduction.
Sears Brands Management Questions? Call the Kenmore ON KENMORE WATER SOFTENER ON WATER SOFTENER according to all instructions in material and workmanship for free repair.
248-CMR 10.00 shall be adhered Consult with a licensed plumber. European equipment Equipment place nationally state and local laws for proper disposal Questions? Call the Kenmore • Use only lead-free before installing Follow all steps connections, them installing damage.
The efficiency rating is only valid rated according to NSF/ANSI Variable Salt Dose: The salt dose is selected Questions? Call Kenmore (Grains @ Salt Dose) of Salt @ Minimum Salt Dose) Ion Exchange Resin Hardness Iron / maximum)
• Locate a Central Water Filtration water supply, or DOWNSTREAM Questions? Call Kenmore Remove and discard Thoroughly check To avoid loss of small parts, we suggest you keep the damage small parts in the parts bag until you are ready to use them.
4. Keep outside faucets on hard water water and salt. See Fig. 4. Questions? Call the Kenmore TYPICAL INSTALLATION you choose a place 5. Do not install freeze. ranty by Sears Brands Management...
3-valve bypass in your plumbing, skip step 6, but perform step 7. Questions? Call the Kenmore incoming psi, buy and install a pressure reducing pipe supplying The highest NOTE: If water more, pressure during 125 psi.
Plastic clip snaps into groove in bypass or adaptor ALTERNATE BYPASS VALVE If connecting level plumbing, the bypass valve turned downward, Questions? Call the Kenmore ASSEMBLE (cont.) installation Measure, and support pipe and fittings that the incoming inlet side. CAUTION:...
NOTE: Drain Hose (20 ft.) is included. See also parts list. Salt Tank Overflow Hose Questions? Call the Kenmore HOSE COPPER DRAIN require the use a copper drain tubing tube is also best to use if running a drain line overhead. (see...
Questions? Call the Kenmore steps: pipes, be steps exactly faucets down- position (see bypass, close the pipe shutoff valve.
Turn on the gas (or electric) supply to the water and light the pilot. YOUR PLUMBING INSTALLATION ELECTRICAL WORK ARE NOW Questions? Call the Kenmore is often used To maintain in the across the inlet sure good power. 120 volt AC soft- only.
"Hardness" screen. Questions? Call the Kenmore Display LOW SALT indicator SET WATER HARDNESS into the electrical out- If you completed NESS" should show in the display.
SELECT button, and the display to the normal run (time of day) screen. oo_1 -t. i-I 2. rC WATER FLOW Questions? Call the Kenmore START TIME Otherwise, Figure 19 is not bypasses during start time is buttons to...
4. If your softener does not have a KCI salt setting, you must increase your hardness setting ensure continuous soft water. Questions? Call the Kenmore allow 50 gallons tem. cover and pour faucet. bleach into Your new Sears softener the brinewell cover.
5J.r_ RECHARGE TONIGHT -I. I-I.M ] ii::i WATER FLOW Questions? Call the Kenmore SALT MONITOR (regeneration) The water are: remind you to add salt to the storage tank. NOTE: You must set salt level each time salt is added to the water softener.
MUST turn the efficiency The softener may initiate recharges, but it will operate pound of salt or higher. Questions? Call the Kenmore 2. Press SELECT again screens shown below. REGENERA- CLEAN: This feature containing (sand, silt, dirt, etc.). and fast rinse cycle will occur first, preceding...
OFF. If this feature is desired, pressing the UP f button. Questions? Call Kenmore Days" 6. Press SELECT again screen. RECHARGE DAY ] Example: regenerations 12 OR 24 HOUR CLOCK: All time displays in standard...
Valve Position Indicator Questions? Call Kenmore PROGRAM If electrical Press this button play is blank but the electronic rect time for several hours. comes on again, you will have to reset the present time only if the display...
SALTBRIDGE Sometimes, a hard crust or salt "bridge" brine tank. It is usually caused by high humidity wrong kind of salt. When the salt "bridges," space forms between the water and the salt. will not dissolve in the water to make brine. brine, the resin bed is not recharged will result.
Valve drain Error code appears Fault in electronic (example: "Err3") ness connections switch inoperable Questions? Call the Kenmore make the following easy checks. for service. If you do not find anything call your Sears Service Department. CAUSE unplugged at wall outlet, or...
MANUALLY INITIATED ELECTRONIC 1. To enter diagnostics, press the SELECT button hold for three seconds. The display show turbine count, valve cycle position, switch status (open or closed). Turbine Count Valve Position (No Water Indicator Flowing) uuu! Im12 WATER FLOW Position Switch Indicator (Open)
MANUAL ADVANCE REGENERATION This check verifies proper operation brine tank fill, brine draw, regeneration other controller functions. Always checks first, and perform the manually tronic diagnostics. NOTE: The display must show a steady ing). If an error code shows, first press the SELECT button to enter the diagnostic 1.
Questions? Call the I<enmore Water Line 1-800-426-9345 or visit www.kenmorewater.com...
Questions? Call the Kenmore Rating Decal "_.'_ Location Water Line 1-800-426-9345 ', 1/[ or visit www.kenmorewater.com...
• 7214375 (includes Key Nos. 12 & 13) Brinewell Decal, Salt Level 7324879 Salt Storage Tank 1103200 Adaptor Elbow 9003500 Grommet Questions? Call the Kenmore Part No. 7327584 0502272 7113058 • 7112963 (PWA) decal below) 7077870 7141001 7176292 7088033 Hardware...
9493 __ Questions? Call Kenmore Water Line 1-800-426-9345 _ 62 Cross-Section _" 67 View or visit www.kenmorewater.com...
Turbine & Support • 7113040 (includes 1 ea. of Key Nos. 74, 75 & 2 ea. of Key No. 71) Turbine Support & Shaft Turbine Questions? Call the Kenmore Part No. 7082053 7081201 (2 req.) 7170319 7081104 1202600 7095030 1148800...
For expert troubleshooting For repair of carry-in items like vacuums, and electronics, call anytime for the location of your nearest Sears Parts & Repair Service 1-800-488-1222 www.sears.com To purchase a protection agreement 1-800-827-6655 (U.S.A.) Para pedir servicio de reparaci6n a domicilio, y para ordenar 1-888-SU-HOGAR (1-888-784-6427)