Page 1: Table Of Contents
Contents 11. Introduction 1.1. Overview 1.2. Main Features 12. Safety/Precautions 2.1. Safety 2.2. Precautions 13. Check Point before Use 3.1. Accessories 3.2. The Satellite dish 14. Controls/Functions 4.1. Front Panel 4.2. Rear Panel 4.3. Remote Control 15. How to Connect 16.
Page 2: Introduction
Introduction 1. 1 Overview This Dual tuner PVR(Personal Video Recorder) with Common Interface is your “Window to the World” giving you the opportunity to enjoy scrambled programs. Enjoy the rich choice of more than 4,000 different channels, broadcasting a large range of culture, sports, cinema, news, events, etc. This receiver is a technical masterpiece, assembled with the highest qualified electronic parts.
Page 3: Safety/Precautions 3
Safety/Precaution 2. 1 Safety Be sure to read the user's manual before Do not touch the power cord with wet hands starting the operation of the unit. as it may cause electric shock. Never open the cover. It is very dangerous to Place the unit in a well ventilated and no- touch the inside of the unit due to possible heat environment.
Page 4: Safety/Precautions
Safety Precautions Precautions When installing the unit Install the unit horizontally. An uneven Do not put heavy items such as a TV on the installation may cause the unit to be unit. That may cause the unit to be damaged. damaged.
Page 5: Check Point Before Use
Check Point before Use 3. 1 Accessories Accessories of the Unit User's manual : 1 Remote control : 1 INFO AUDIO GUIDE CH.LIST AUX IN RECALL MENU EXIT TV/RADIO TV/SAT LIST SLEEP Batteries (AAA type) : 2 RCA Cable : 1 USB Cable (A-B Type) : 1 Loop Through Cable : 1 If any accessories listed above are missing, contact the sales representative where you purchased...
Page 6: Controls/Functions
Controls/Functions 4. 1 Front Panel 10 13 11 Power : To switch the receiver in “standby” mode or in power on mode. Channel Display ( 4 Digit ) - When you connect the power line of the receiver, the current time is displayed. - After programming, the program number or name is displayed.
Page 7: Rear Panel
Controls/Functions Rear Panel Name Connector Function LNB1 INPUT IEC 169-24 Female IF input from LNB to Digital Tuner 1 LOOP1 OUT IEC 169-24 Female IF Loop-through output from Digital Tuner 1 LNB2 INPUT IEC 169-24 Female IF input from LNB to Digital Tuner 2 LOOP2 OUT IEC 169-24 Female IF Loop-through output from Digital Tuner 2...
Page 8: Remote Control
Controls/Functions Remote Control POWER : To switch into ‘standby’ or ‘power on’ mode. MUTE : To turn the sound on/off. Numeric Keys(0-9) : To input numeric value, channel number or characters. INFO. : To display the information of the current channel.
Page 9 Controls/Functions Remote Control : To add a new channel to the Channel List IVORY menu. To stop the played programs on HD. ORANGE ( LIST ) : To see variant channel lists for user's convenience in the Channel List menu. To watch the list of stored programs on HD.
Page 10: How To Connect
How to Connect 5. 1 Connecting IRD to Hi-Fi system and TV, VCR with SCART Connecting Tuner to two separated Antennas Note : At tuner select in LNB Configuration menu, #1 or #2 mode should be selected. How to Connect...
Page 11 How to Connect Connecting Tuner to one Antenna Note : At tuner select in LNB Configuration menu, Loop mode should be selected. Connecting Tuner to Twin LNB Antenna Note : Each LNB corresponds to one satellite. At tuner select in LNB Configuration menu, #1 or #2 mode should be selected for each LNB.
Page 12 How to Connect Connecting Tuner to two separated Twin LNB Antennas Note : At tuner select in LNB Configuration menu, #1 & #2 mode should be selected. If #1 and #2 mode is selected in other configuration, bad or no signal can be displayed.
Page 13: Operation
Operation After your receiver is powered up, proceed with installation as follows: 6. 1 Getting Started 1. Menu Language Setting When you plug in AC power, the following will be displayed on the front. Press POWER on remocon, the LED number will be displayed as follows; Press MENU key and position cursor on ‘Language' column with Select language you want with or .
Page 14 Operation 6. 1 Getting Started Press INFO. Then you can see the help window of the selected content. 3. Satellite Setting Since your receiver has the basic data of most satellites and channels, you can receive programs just by plugging in. But, according to the status of your antenna setup, you may have to modify the basic data of satellites and / or channels.
Page 15 Operation 6. 1 Getting Started If you press , the selected Satellite will be added and the cursor will move to right window for detailed installation. Note : If you just want to edit the data of the satellite which is already contained in the receiver, press after you select the satellite.
Page 16 Operation 6. 1 Getting Started Level Indicating selected satellite signal strength level Quality Indicating signal to noise ratio Select the satellite you want with or . Press to move to TP section and select the TP you want with or . When the satellite and the TP are selected, you can check the reception status of the satellite signal.
Page 17: Getting Started
Operation 6. 1 Getting Started 5. Satellite Scan After finishing ‘Antenna Setup’, execute a ‘Satellite Scan’. Then you can get all channels in the pre-programmed TPs. This function can also be used to get the latest channel data while receiver is in use. Through this function, the receiver searches for all the available channels and saves them in the memory.
Page 18: Select Channel
Operation 6. 1 Getting Started After the scanning process, the first channel of the last scanned TP will be displayed on the back screen. Press to finish the process. Then select a channel and press to watch a program or press MENU key or EXIT key.
Page 19 Operation Channel Editing 1. Favorite Channel You can set up favorite channel lists as you want. For example, if you want to set favorite channel lists as following. Favorite1 : 7 DWtv, 6 Hunan1 Favorite2 : 1 Fujian1 Favorite3 : 3 ANHUI TV, 5 Guangdong1 Firstly, set favorite1 channels.
Page 20 Operation Channel Editing Select ‘Favorite 1’ with TV Channel List AsiaSat 2 All List Favorite State [24] 4,847 GHz Fujian 1 Favorite 1 Horizontal-18V DIGITL VID Favorite 2 28,123 MSPS ANHUI TV Dban Favorite 3 NMCHTV Guangdong 1 Favorite 4 FAV.
Page 21: Channel List
Operation Channel Editing You can see ‘Channel List Mode' window. Select ‘Favorite' with and select ‘Favorite1' with or . TV Channel List AsiaSat 2 All List Channel List Mode [20] 3,847 GHz Fujian 1 Free+Scrambled Horizontal-18V DIGITL VID 4,420 MSPS Favorite Favorite 1 ANHUI TV...
Page 22 Operation Channel Editing Select ‘D' with or . TV Channel List AsiaSat 2 All List Channel List Mode [20] 3,000 GHz Fujian 1 Free+Scrambled Horizontal-18V DIGITL VID 4,420 MSPS Favorite Favorite 1 ANHUI TV Deutsche Well NMCHTV Satellite AsiaSat 2 Guangdong 1 Alphabet FAV.
Page 23 Operation Channel Editing Free + Scrambled Mode Press ORANGE in the channel list and select first line with Select ‘Free+ Scrambled' with or . TV Channel List AsiaSat 2 All List Channel List Mode [20] 3,20 GHz Fujian 1 Free+Scrambled Horizontal-18V DIGITL VID 4,420 MSPS...
Page 24: Channel Editing
Operation Channel Editing 3. Lock Channel This menu enables you to prevent children from viewing programs unsuitable for their age. Press CH.LIST and select the channel you want to lock with and press GREEN. Then the selected channel is locked. Note : If ‘password’...
Page 25 Operation Channel Editing Press YELLOW. TV Channel List AsiaSat 2 All List [24] 4,000 GHz RAI Internati Horizontal-18V RTPi 28,123 MSPS Deutsche Well TV5-Asia uØoH-u1/4Ö¥x CS FAV. ªFËê>>Ú¥x ET LOCK «DoZ¥x USTV-I oé¥>>¥x JET MOVE MODE -Page Up/Down, -Watch, -Main, -EXIT, -Move Press MENU, EXIT or...
Page 26 Operation Channel Editing 6. Add Channel Press CH.LIST. Press Ivory. Add Digital Channel Satellite Name AsiaSat 2 TP Frequency [24] 4,000 GHz Polarization Horizontal-18V Symbol Rate 28,123 MSPS CH. Name DWtv Video PID 2305 Audio PID 2306 PCR PID 2304 Select a satellite into which you want to add your new channel.
Page 27: System Parameters
Operation System Parameters 1. Setting Age Restrictions This sub-menu allows you to set the age for parental locking and protect children from viewing programs unsuitable for their age. Press MENU key. Press to select ‘System Parameters' and press Press to select ‘Parental Control' and press System Parameters Parental Control PASSWORD...
Page 28 Operation System Parameters 2. Security Check You can set SECURITY CHECK to protect your current installation from being changed (location shift, deletion, adding etc.) or modifying of installed data. Press MENU key. Press to select ‘System Parameters' and press Press to select ‘Parental Control' and press Enter 4-digit password.
Page 29: System Information
Operation System Parameters 4. Personal Information Setting You can enter your personal information, such as your name and address, etc. Press MENU key. Press to select ‘System Parameters' and press Press to select ‘Parental Control' and press Enter 4-digit password. Note : The default password is '0000'.
Page 30 Operation System Parameters 6. Setting Timer (Automatic power On/Off) You can pre-set the on/off time of your receiver. During your absence, you can record programs on your VCR. Press MENU key. Press to select ‘System Parameters’, and press Press to select ‘Local Time/Timer’, and press Note : Without the local time setting, this ‘TIMER’...
Page 31 Operation System Parameters 7. Setting Day Light Saving Time (Summer Time) You can adjust current local time when summer time is applicable. Press MENU key. Press to select ‘System Parameters’, and press Press to select ‘DL Saving’. Press to select ‘Yes’ or ‘No’. Set for daylight saving function activated.
Page 32: Setting Screen
Operation System Parameters When your TV is 4:3. 16x9 When your TV is 16:9. Auto When setting suitable aspect ratio automatically. Note : If you set 4 x 3 when the Satellite input signal is 16 x 9, the right and the left parts of the original picture may not be seen.
Page 33: Transponder
Operation Transponder 1. TP Edit / Scan After ‘LNB Configuration’ and ‘Antenna Setup’ procedure, when necessary, you can edit and/or add certain TPs ( transponders ) Press MENU key. Select ‘Installation’ with , and press Select ‘TP Edit/Scan’ with , and press TP Edit/Scan Satellite Name AsiaSat 2...
Page 34 Operation Transponder After scanning process, the first channel of scanned TP will be displayed. TP Edit/Scan Success Radio: RAI Internati DW 9 RDP ANTENA 1 TV5-Asia RDP ESPECIAL Good RTPi uØoH-u1/4Ö¥x CS ¥xÆW N¥<< TWN ªFËê>>Ú¥x ET ¥@uØ Auø USA- «DoZ¥x USTV-I oé¥>>¥x JET AsiaSat 2...
Page 35: Factory Set
Operation Factory Set The status of the receiver will return to factory default parameters by using this function. Press MENU key. Select ‘Installation’ with , and press Select ‘Factory Set’ with , and press When the menu asks you to confirm the reset, press if you want to reset or press EXIT key if you want to void the reset.
Page 36 Operation On Air Download Press at ‘Start'. It takes a few minutes to search the group of program & download channel. If there is problem in searching the necessary information, then other window is open. On Air Download On Air Download Astra [1] 12,603 GHz HotBird...
Page 37 Operation Other Function on Remote Control Select Channel with Then you can see current or next program information of the selected channel. If you press GREEN, current or next program information would be converted to next or current program information respectively. Program Guide Program Guide 19:33...
Page 38 Operation Other Function on Remote Control You can set up automatic power on-off ( Timer ) or automatic recording on the program schedule list. After pressing YELLOW in the Guide ( EPG ) menu, select a program with and press Select ‘Once/Daily/Weekly/No' of ‘Status' with or .
Page 39: Other Function On Remote Control
Operation Other Function on Remote Control 3. Subtitle/Audio You can adjust the subtitle and audio condition/status of the current channel. Press ‘AUDIO’ and subtitle and audio related window will be displayed on the screen. Subtitle/Audio Subtitle Track 2 of 10 [Swedish] Audio Track 1 of 8 [English] Audio Mode...
Page 40 Operation Other Function on Remote Control 4. Teletext Teletext Service is text data service from Service Provider. It is available only when the satellite signal carries teletext service data. Press BLUE key and wait. If ‘*’ sign is pops up in the left upside of the screen as the following picture, wait until teletext service menu is displayed because ‘*’...
Page 41: Sleep Timer
Operation Other Function on Remote Control 5. Sleep Timer Your receiver will automatically power-off when the time you set is passed. Press ‘SLEEP’ key until the right time you want appears. Note : 1. You can set SLEEP TIMER in 30 minute steps up to 150 minutes. 2.
Page 42: Picture In Picture
Operation Other Function on Remote Control 7. Channel / Information Brief information is displayed, such as current channel type, name, local start/end time, guide information, current time, fav/normal mode, Audio mode and Audio ID. Press INFO, then the information bar will pop-up. AsiaSat 2 5 DWtv 13:41...
Page 43: Zoom Function
Operation Picture in Picture 2. PIP swaping You can swap main-picture window and sub-picture window by pressing PIP swap ( ) key. If PIP function is running, press PIP swap ( ) key. Main-picture and sub-picture will be swapped Zoom Function 1.
Page 44: Hard Disk Operation
Hard Disk Operation 7. 1 Recording 1. Start Recording You can record the current channel by pressing RED ( ) key. If program Guide menu pops up, you can record any channel you want. Press RED ( ) key to record current channel. In Program Guide menu, press RED ( ) key to record after selecting a program you want.
Page 45 Hard Disk Operation 7. 1 Recording HD-Program Guide 11:20 Title Play Type Do you want to stop recording? Default Event Play time Free 38.8 GB (99.4%) 28/08/2001 11:20 Default Event -Wotoh, -Delete, -Satellite Mode Note : If there is no HDD access for 5-minutes, the receiver will go into sleep mode. If one channel is recorded, press key to stop recording.
Page 46: Playing
Hard Disk Operation Playing 1. Start Playing You must select a program to play stored programs. For entering HD-Program Guide menu, press ORANGE ( LIST ) key. Press ORANGE ( LIST ) key. In HD-Program Guide, select a program by pressing HD-Program Guide 11:52 Title...
Page 47: Delete Programs
Hard Disk Operation Delete Programs You can delete any program in HD-Program Guide menu. Press ORANGE ( LIST ) key then HD-Program Guide menu will pop-up. In HD-Program Guide, select a program with Press RED ( ) key to delete the program then Delete dialog menu will pop-up. HD-Program Guide 11:52 Title...
Page 48: Skip Play
Hard Disk Operation Lock Programs Lock Clear skip points Split take 1 SABe TV Netwo 00:00:16 / 00:01:10 2 Ch Default Event Select ‘LOCK’ using Press , LOCK enable or disable will be setted with Yes or No. Note : The password for playing a stored program is the same password for any other lock operation. Skip Play You can set the part you don't want to play, such asadvertisements.
Page 49: Bookmark
Hard Disk Operation Skip Play Then a proper pair of start and end points will be displayed with yellow pointers on the Bar. 5 CH 22 - Indus 00:06:03 / 00:24:53 2 Ch CH 22 - Indus Note : To try to set an improper pair will be rejected. Press RED ( ) key at the position between start and end points, then the skip-point will be removed.
Page 50: Repeat
Hard Disk Operation Bookmark Press go to bookmark ( ) key to jump to the previous bookmark. To remove a bookmark, select the bookmarked position by go to bookmark ( ) key and press bookmark ( ) key. Repeat 1. Repeat Mode You can repeat playback by pressing REPEAT ( ) key.
Page 51: Split Operation
Hard Disk Operation Repeat Once more, Press REPEAT A-B ( ) key to display repeat A-B message. And selected region is played repeatedly. If HD-Information bar pops up, icon display on HD-Information bar. 1 RAI Internati 00:00:10 / 00:01:10 2 Ch RAI Internati To stop repeat A-B function, press REPEAT A-B ( ) key once more.
Page 52: Trick Play Controls Without Osd
Hard Disk Operation Split Operation Press to start splitting or EXIT key to cancel. If split operation starts, the progress window will pop-up and you can see the status of process. HD-Program Guide 12:00 Title Play Type Now splitting program Default Event 00:01 CH 25 - DBN 24...
Page 53: Conditional Access
Conditional Access Insert CA Module ( s ) and Smart card ( s ) 8. 1 To receive pay-TV channels you need a CA Module and a Smart card from the service provider (program distributor) of your preference. If you are subscribing to services from more than one service provider, you need to change different smart card or even different CA Modules.
Page 54 Conditional Access Information about CAM and Smart Card You can check the status of CAM and smart card inserted in their slots. Press MENU key. Press , and select the Common Interface you want, then press Brief information on selected CAM will be displayed. Common Interface Slot #1 Version...
Page 55: Trouble Shooting
Trouble Shooting There may be various reasons for the abnormal operation of the unit. Therefore, if the unit does not work properly, check it according to the procedures shown in the table below : Problem Possible causes Remedy LED on front panel AC power cord disconnected.
Page 56: Specifications
Specifications System capabilities Fully DVB compliant LNB/Tuner input Connector IEC 169-24, female Frequency range 950MHz 2150MHz Signal level -65dBm 25dBm LNB supply 14/18V, max 400mA LNB switch control 22KHz DiSEqC Ver 1.2 & Ver 1.0 Compatible Demodulator Front end QPSK Symbol rate 2Msps 45Msps...
Page 57 Specifications Power supply Power consumption max 60W Supply voltage 240V Supply frequency 47Hz 63Hz Rear Panel connectors Video out 1 X RCA cinch Audio L/R 2 X RCA cinch Digital Audio Out 1 X RCA cinch 1 X Optical Serial data 9pin D-sub USB B-Type Connector Digital tuner input...

Hyundai HSS-880HCI User Manual

Quick Links

Related Manuals for Hyundai HSS-880HCI

Summary of Contents for Hyundai HSS-880HCI

Table of Contents