1. Manuals
  2. Brands
  3. T.MIX Manuals
  4. Mixer
  5. DPM-1122
  6. Owner's manual

T.MIX DPM-1122 Owner's Manual

Power mixer with 24-bit digital effects
Hide thumbs
Table of Contents

Advertisement

Quick Links

DPM-1122
Owner's Manual
POWER MIXER
with 24-bit Digital Effects

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DPM-1122 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for T.MIX DPM-1122

  • Page 1 DPM-1122 Owner‘s Manual POWER MIXER with 24-bit Digital Effects...

  • Page 2: Table Of Contents

    Contents Important Safety Instructions! ..........................3 Cleaning and Care ............................3 Introduction ..............................4 Features ................................4 Quick Start ................................4 Becoming acquainted with the Operational Surface ..................5 Small Gig Hookup Diagram .........................6 Computer Set-up Diagram ..........................6 The Control Elements ............................7 . . . on the front Panel ..........................7 .

  • Page 3: Important Safety Instructions

    Important Safety Instructions! For your own safety you must read through this chapter at first completely! Risk of electrical shocks. • Only connect the device to a properly wired and earthed mains power socket providing mains voltage of 230 V ~ /50 Hz. •...

  • Page 4: Introduction

    Built-in high-quality D class amplifier with signal, CLIP, and protection LEDs. Quick Start This is the fastest way to get something out from your THE T.MIX DPM 1122, if you have a keyboard and a microphone. 1. Plug the microphone into channel 1 MIC IN. 2. Turn down AUX and LEVEL controls on that input channel.

  • Page 5: Becoming Acquainted With The Operational Surface

    Becoming acquainted with the Operational Surface...

  • Page 6: Small Gig Hookup Diagram

    Small Gig Hookup Diagram (the displayed amplifier is optional - of course you can connect the speakers to the speaker sockets on the rear panel of the mixer.) Computer Set-up Diagram...

  • Page 7: The Control Elements

    12 MIC channels only. For the other channels you can always insert the processor in between the sound source (such as keyboard or drum machine) and the THE T.MIX DPM 1122 input. The insert sockets can be used as direct-outs to feed the input of a multi-track recorder.
  • Page 8 7. HI If you turn this control up, you will boost all the frequencies above 12 kHz (shelving filter). You will add transparency to vocals and guitar and also make cymbals crispier. Turn the control down to cut all frequencies above 12 kHz.
  • Page 9 17. PEAK LED Inside your DPM 1122 the audio signal is monitored in several different stages and then sent to the PEAK LED. When the LED is red illuminated, it warns you that you are reaching signal saturation and possible distortion. Then you should reduce the input level for avoiding distortion. 18. FADER This fader will adjust the overall level of this channel and set the amount of signal sent to the main mix.
  • Page 10 27. FX1/2 TO MAIN Level Control This fader is used to adjust the level of the processed signal which is sent from the DSP to MAIN MIX bus. 28. AUX1-4 Controls These knobs are used to adjust the amount of the signal sent from the AUX SENDS1-4 jacks to the AUX1, 2 ,3 and 4 buses.
  • Page 11 39. COMP./BYPASS Switch & LED Push this switch, the LED will light up and you will activate the MAIN MIX COMPRESSOR. You can also use the bypass switch to make a comparison between processed and unprocessed signal. 40. AUX SENDS Connectors These 1/4” phone jacks are used to send out the signal from the AUX bus to external devices such as effect units and/or stage monitors.

  • Page 12: On The Rear Panel

    2. Connect phantom powered microphones before switching on the +48 Volt phantom power switch. 3. Set the output level of your THE T.MIX DPM 1122 or the connected power amplifier at no more than 75%. 4. Position EQ controls on middle position.

  • Page 13: Audio Connections

    Audio Connections You can connect unbalanced equipment to balanced inputs and outputs. Simply follow these schematics:...
  • Page 14 And now some tips how to use the AMPLIFIER MODE switch This is the most common application. The built-in amplifier drives two main speaker cabinets Left and Right. The AMPLIFIER MODE is on MAIN L+MAIN R position. With the AMPLIFIER MODE in AUX1+AUX2 position, the built-in amplifier drives two monitor speakers. With the AMPLIFIER MODE switch in BRIDGE position the two power amplifiers in your DPM 1122 drive together a single speaker cabinet with the sum of the power of the 2 amps.

  • Page 15: Preset List

    Preset List...

  • Page 16: Block Diagram

    Block Diagram...

  • Page 17: Technical Specifications

    Technical Specifications...

  • Page 18: Disposal

    Disposal Never throw the device into the regular household waste at the end of its useful life. This product is subject to the European Directive 2002/96/EC. • Dispose of the device through an approved disposal centre or at your community waste facility. • Observe the current existing regulations. In case of doubt contact your disposal facility. • The packaging is certified via a dual system. Take all packaging materials to an environmentally friendly disposal facility in compliance with the local regulations.
  • Page 20 © 2010 Musikhaus Thomann Treppendorf 30 • 96138 Burgebrach • Germany www.thomann.de...

Table of Contents