Advertisement
Quick Links
SunTouch P-3285 DualTemp Digital Outdoor Instructions
24v for use with CP ContactorPro Panels (CP-50/100/200)
To enter the parameter menu, press and hold the OK button for 5 seconds.
•
Use the +/- keys to select the installation parameter to be adjusted.
•
Press OK to toggle the parameter setting or to edit its value. When the value begins to blink, use the
+/- keys to adjust its value. Press OK to select the adjusted value.
•
Toggle to "End" and press OK to exit the installation parameter menu.
•
(Only Bold apply to Outdoor Patio Heating)
Parameters
• J0: °C/°F Temperature display section.
•
J1: Hot
•
Cy: Proportional Integral regulation time cycle, value in minutes (default: 15 minute cycle).
•
bp: Proportional Integral regulation band amplitude value in degrees °C/°F (default: 2.0°C/3.6°F).
•
J4
: NO/
NC: If using an isolation relay and/or a relay box.
NO: if connecting to a Watts Zone Valve control.
•
J5: Select PMP (Pump Maintenance Program) to perform a 1 minute exercise every day.
•
J6:
Air: Air (room) setpoint. Displays air temperature with floor low (FL) and high (FH) limits.
Flr: Floor (external sensor) setpoint. Displays floor temperature
without floor low/high limits. Air temperature is not a control
boundary.
Air temp is not used because the T-stat is mounted INSIDE and the
area to be monitored is OUTSIDE and monitored with Floor Sensor
Only
•
J7: rEG (proportional Integral) or HYs (0.3°C Hysteresis) regulation type selection.
•
Cp: Proportional Integral regulation temperature compensation value in °C/°F
•
(default: 2.0°C/3.6°F).
•
Ao: Air Sensor offset adjustment (default: no offset), display measure air sensor value.
•
Fo: Floor sensor offset adjustment (default: no offset), display measure floor
•
sensor value.
•
FL: Floor temperature LOW limitation (default: 5°C/41°F), effective only if floor
•
sensor present and set J6 to Air.
•
FH: Floor temperature HIGH limitation (default: 28°C/82°F), effective only if floor
•
sensor present and set J6 to Air.
•
CLr: Press OK to reset to factory defaults.
• End: Press OK to exit installation parameters.
/Cold regulation mode. Select Hot for Heating, Cold for cooling.
NC
Normally Open or Normally Close actuator selection.
23055 Alcalde Drive, Laguna Hills, CA 92653
Toll Free 866 – 558 – 3369 ● Fax 866 – 558 – 2010
CustomerCare@warmyourfloor.com
www.WarmYourFloor.com
Advertisement
Summary of Contents for WarmYourFloor SunTouch P-3285
- Page 1 Toll Free 866 – 558 – 3369 ● Fax 866 – 558 – 2010 www.WarmYourFloor.com CustomerCare@warmyourfloor.com SunTouch P-3285 DualTemp Digital Outdoor Instructions 24v for use with CP ContactorPro Panels (CP-50/100/200) To enter the parameter menu, press and hold the OK button for 5 seconds.
- Page 2 07-3-857-40-02 For Residential and Commercial Applications Job Name ––––––––––––––––––––––––––––––––––––––––––– Contractor –––––––––––––––––––––––––––––––––––––––––––– Job Location ––––––––––––––––––––––––––––––––––––––––– Approval ––––––––––––––––––––––––––––––––––––––––––––– Engineer ––––––––––––––––––––––––––––––––––––––––––––– Contractor’s P.O. No. ––––––––––––––––––––––––––––––––––– Approval ––––––––––––––––––––––––––––––––––––––––––––– Representative –––––––––––––––––––––––––––––––––––––––– DualTemp Digital Thermostat Dimensions: 3-3/8" x 3-3/8" The Watts Radiant DualTemp thermostat has the ability to sense the temperature of the air, fl...
- Page 3 PARAMETER MENU INSTALLATION PARAMETERS To enter the parameter menu, press and hold the OK button °C/°F Temperature display section. for 5 seconds. Hot/Cold regulation mode. Select Hot for Heating, Cold for cooling. Cy: Proportional Integral regulation time cycle, value in minutes Use the +/- keys to select the installation parameter to be adjusted.
Need help?
Do you have a question about the SunTouch P-3285 and is the answer not in the manual?
Questions and answers