Advertisement
IST-I600 Installation Manual
Thank you for purchasing an Intrasonic Technology product. Our products
are built to provide you with years of high quality sound.
If you need assistance with the installation or operation of this product,
please contact our Customer Service Support team at 1-877-435-0670.
You may also get information on this and other Intrasonic Technology
products on our website at
www.intrasonictechnolgy.com
Intrasonic Technology | 9525 Forest View Street | Dallas, Texas 75243|877-435-0670
pg. 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for IST IST-I600
- Page 1 IST-I600 Installation Manual Thank you for purchasing an Intrasonic Technology product. Our products are built to provide you with years of high quality sound. If you need assistance with the installation or operation of this product, please contact our Customer Service Support team at 1-877-435-0670.
-
Page 2: Important Safety Instructions
Important Safety Instructions 1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. -
Page 3: Table Of Contents
Table of Contents Cover Page Safety Instructions Table of Contents Connecting Power Connecting the Antenna Connecting Speakers without Volume Controls Volume is controlled from the I600 system Connecting Additional Amplifiers (Optional) Connecting Volume Controls (Optional) Connecting an External Auxiliary Wall Plate Used for CD Players, Satellite etc…... - Page 4 Connecting the Power 1. Once a location has been selected for the I600 unit, use the provided template to cut a hole in the wall. Should be approximately 50” above the floor. ( 5 1/2” Tall and 10” Wide). 2. Run a dedicated power to the location of I600 unit. The power supply on the I600 unit can automatically detect the voltage applied directly to the unit.
-
Page 5: Connecting The Antenna
Connecting the Antenna 1. The AM and FM antennas needs be located in the attic or highest point in the house. Make sure to secure the antennas. 2. Keep the AM and FM antennas away from high voltage. 3. The RG59 connector on the FM Antenna connects to the I600 system and the RED and BLUE end is left in the Attic or the highest point in the house. - Page 6 Connecting Speakers to I600 or I600-AMP 1. Once the location of the speakers have been selected, run 2 pairs of 16 gauge 2 conductor speaker wire from each pair of speakers (Maximum of 4 pairs) to the I600 system. Only 8-Ohm speakers (Suggested Speakers are 100C or EX-C80II) are to be used with the I600 System.
-
Page 7: Connecting Additional Amplifiers (Optional)
Connecting Additional Amplifiers (I600-AMP OPTIONAL) Note: Unlimited number of I600-AMP Amplifiers can be installed per system. Maximum 4 pairs of speakers per I600- AMP Amplifier can be connected. 1. The I600-AMP is usually located in a closet or in a location out of sight. Use 22 AWG 75 Ohm Coaxial Cable (RG59) RCA Connectors. -
Page 8: Connecting Volume Controls (Optional)
Connecting Volume Controls (Optional) 1. Volume controls are only needed when the desire to control the volume in individual rooms. Without volume controls the I600 Main System will be controlling the volume for the entire system. Once the location of the volume controls have been selected, run 2 pairs of 18 gauge 2 conductor speaker wire from the I600 System or I600-AMP to the Volume Control (Suggested Volume Controls are JA-VNB-75 or JA-VSL-100) then from the volume control to each pair of speakers (Maximum of 4 pairs) to the I600 system or I600-AMP. -
Page 9: Connecting An External Auxiliary Wall Plate
Connecting an Auxiliary Wall Plate (Optional) 1. An Auxiliary Wall Plate is used when connecting external sources such as CD Players, Satellite etc… 2. Once you have chosen the location of the Auxiliary Wall Plate, run a RCA Audio Cable from the I600 System to the Auxiliary Wall Plate. -
Page 10: Installing The I600 Into The Wall
Installing the I600 into the Wall 1. Remove the front cover of the I600 to expose the (4) screws. Diagram 1 points to the 4 screws. 2. Insert the I600 into the wall; use a Phillips screw driver to tighten the CAMLOCKS. Notice the CAMLOCKS will compress against the wall as you tighten the screws.
Need help?
Do you have a question about the IST-I600 and is the answer not in the manual?
Questions and answers