Subscribe to Our Youtube Channel
Summary of Contents for Itec MULTIMIX 8/4 DIGITAL
- Page 1 MULTIMIX 8/4 digital MANUAL VERSION 3.0, AUGUST 2007 PART 1: HARDWARE DESCRIPTION www.itec-audio.com...
-
Page 2: Dear Customer
The ITEC-MULTIMIX 8/4 digital fulfils this requirement to perfection. With his PC, the technician can easily configurate the device as requested and implement a wide variety of sound effects without using additional devices. -
Page 3: Table Of Contents
MULTIMIX 8/4 DIGITAL CONTENTS: PART 1 HARDWARE DESCRIPTION Dear customer! ........................2 SAFETY PRECAUTIONS ......................4 SUPPLY EXTENT........................5 PART 1: HARDWARE DESCRIPTION ................6 FRONT PANEL CONTROLS and DISPLAY ...............6 1) Power indicator:........................... 6 2) Multifunctional LED display: ......................6 3) Potentiometers 1- 8: ........................7 4) PC interface:.......................... -
Page 4: Safety Precautions
MULTIMIX 8/4 DIGITAL SAFETY PRECAUTIONS The installation and configuration of the ITEC-Multimix 8/4 must be carried out solely by trained experts. For the configuration use exclusively the original software ITEC-MixDesign. You must only use the original power supply, which has on its primary side an IEC power inlet C14 and which is to be connected to the mains socket customary in your country (115 –... -
Page 5: Supply Extent
Input equalizer (built in) Accessories: ITEC-MM-PC-1.5 RS-232 to PC connection cable ITEC-MM-PC-1.5 opto PC connection cable with a galvanically separated interface ITEC-MM-RJ-0.5 Analog-Link-Kabel The standard phantom power of the inputs is 12 Volt. For a higher phantom power you need:... -
Page 6: Part 1: Hardware Description
MULTIMIX 8/4 DIGITAL PART 1: HARDWARE DESCRIPTION FRONT PANEL CONTROLS and DISPLAY Hardware 2.1 Hardware 1.0 to 2.0 1) Power indicator 4) PC-Interface 2) LED-Display 5) Device Status 3) POTIS 1-8 1) Power indicator: A red LED shows that the operation voltages are in order. -
Page 7: Potentiometers 1- 8
MULTIMIX 8/4 DIGITAL 3) Potentiometers 1- 8: A considerable advantage of the ITEC-MultiMix is the manual controllability of the volumes in a most simple form, namely by means of the potentiometers on the front panel. This is the only way of realising a really user-friendly stand-alone solution. The 8 volume controls can be allocated individually;... -
Page 8: Plugs And Sockets Of The Rear Panel
MULTIMIX 8/4 DIGITAL PLUGS and SOCKETS of the REAR PANEL Hardware 2.1 Hardware 1.0 to 2.0 6) Ground lift 10) Digital link 14) Ethernet Port 7) Power supply 11) Analogue link 15) Device Status Output 8) External control inputs 12) inputs 1 - 8... -
Page 9: External Control Inputs
MULTIMIX 8/4 DIGITAL The voltage for phantom power on pin 6 is 12 Volt. By using the plug modules ITEC-MM-Ph-24 and ITEC-MM-Ph-48 respectively you can achieve higher phantom voltages. Attention: When using 48 Volt phantom voltage, short-circuiting the input signal wires on ground must be avoided. -
Page 10: B) External Configuration Switching
MULTIMIX 8/4 DIGITAL Input resistance: 40 kOhm We recommend the use of linear potentiometers 1 k or 5 k. With long wirings you need to use shielded cables (as shown in the illustration). When using linear potentiometers and a scale of 0 – 10, you can determine the influence of the external controls according to the calculation method mentioned in item 3. -
Page 11: Interface For Media Remote Control
MULTIMIX 8/4 DIGITAL Configuration change with BCD coded switch: BCD switch 9) Interface for media remote control: 9-pole Submin-D plug on the housings rear panel, called ”RS-232 Remote“. Settings: Baud rate: 19200 Parity: none Data bits: Stop bits: 1 Attached to the software description you will find the communication protocol between the MultiMix and a media remote control. -
Page 12: Inputs
MULTIMIX 8/4 DIGITAL Provided the configuration of the corresponding Bus signal is set on „ADD-LINK” (see software description “basic configuration”), the incoming Bus signal will be added to the own Bus. The summary Bus signal wil then be available again at the link-out socket. -
Page 13: Optional Lan-Module
Available as an option is a version with a built-in 8-channel 7-band equalizer module. The configuration software for the DSP module is included in the ITEC-MixDesign software. The equalizer module comes with 7-band graphic filters for each input channel, adjustable from -10dB to +10dB in 2dB steps, enabling the user an optimal adjustment of different signal sources. -
Page 14: Multimix 8/4 Block Diagram
MULTIMIX 8/4 DIGITAL MULTIMIX 8/4 BLOCK DIAGRAM www.itec-audio.com MULTIMIX 8/4 DIGITAL... -
Page 15: Optional 4X4 Dsp-Matrix
Available as an option is a version with a built-in 4x4 DSP matrix module. The configuration software for the DSP module is included in the ITEC-MixDesign software and is comfortably easy to use. The DSP module works in 24 Bit / 44.1 kHz mode, and is equipped with the best possible algorithms. -
Page 16: Installing And Removing Modules
MULTIMIX 8/4 DIGITAL Installing and removing Modules Installing the DSP Module A) Hardware installation 1) Remove the top cover of the device (8 screws) 2) Remove 4 jumpers (see picture) 3) If the three spacers aren´t already mounted (marked blue in picture below), remove the bottom cover and fasten the spacers(M3, 15mm) 4) Take the DSP module carefully from the packing and put it onto the main module. -
Page 17: Removing The Dsp Module
6) Reinsert the top and bottom cover B) Software settings 1) Connect the Multimix 8/4 digital with a computer and make sure the device is switched on. 2) Run MixDesign (At least Version 2.0) Go to “Extras”|”Hardware setup” and click menu item "DSP is installed"... -
Page 18: Installing The Input-Equalizer Module
MULTIMIX 8/4 DIGITAL Installing the Input-Equalizer Module A) Hardware installation 1) Remove the top cover of the device (8 screws) 2) Remove 8 jumpers (JP1..JP8, marked red in picture below) 3) If the two spacers aren´t already mounted (marked blue in picture below), remove the... -
Page 19: Removing The Input-Equalizer Module
6) Reinsert the top and bottom cover B) Software settings 1) Connect the Multimix 8/4 digital with a computer and make sure the device is switched on. 2) Run MixDesign (At least Version 2.0) Go to “Extras”|”Hardware setup” and click menu item "Input Equalizer is installed"... -
Page 20: Specifications
TCP/IP, UDP/IP, ARP, ICMP, SNMP, TFTP, Telnet, DHCP, HTTP Internet Web Server MIXDESIGN-SOFTWARE You can download the latest version of our software any time: http://itec-audio.com/download/mixer/mixersetup.exe In case of any questions please contact us: office@itec-audio.com, www.itec-audio.com ITEC Tontechnik und Industrieelektronik GesmbH, A-8200 Lassnitzthal 300 / Austria / Europe Tel.: +43 (0)3133 /3780-0, office@itec-audio.com, www.itec-audio.com...
Need help?
Do you have a question about the MULTIMIX 8/4 DIGITAL and is the answer not in the manual?
Questions and answers