Do you have a question about the Impulse and is the answer not in the manual?
Questions and answers
Stuart H Brydon
May 4, 2025
Hello
Why does the 12v supply keep shitting down after 15minutes?
1 comments:
Mr. Anderson
May 17, 2025
The Exendis Impulse 12V supply may shut down after 15 minutes due to one of several possible failure conditions indicated by LED blink codes. Common reasons include:
- Deep battery discharge (1 blink) - Battery temperature too high or too low (2 or 3 blinks) - Electronics temperature too high (4 blinks) - Output current too high (5 blinks) - Short circuit (6 or 7 blinks) - Input voltage too high (8 blinks)
Each condition causes automatic shutdown for protection. The exact reason can be identified by counting the number of LED blinks followed by a pause.
This answer is automatically generated
Summary of Contents for Exendis Impulse
Page 1
BEDIENUNGSANLEITUNG USER MANUAL GEBRUIKSAANWIJZING Impulse Peak Power Pack Version 1.01...
Page 2
To the extent permitted by law no liability (including liability to any person by reason of negligence) will be accepted by EXENDIS B.V., its subsidaries or employees for any direct or indirect loss or damage caused by omissions from inaccuracies in this document.
Page 3
Eingang durchgeführt werden. Auf diese Weise kann das Impulse Peak Power Pack auch während der Fahrt vom Auto/Dynamo oder auch mit einer Sonnenzellenplatte geladen werden. Bevor Sie das Impulse Peak Power Pack in Betrieb nehmen, empfehlen wir Ihnen diese Bedienungsanleitung sorgfältig durchzulesen sowie die Sicherheitsvorschriften zu beachten.
Page 4
Stunden Stunden Stunden idealen Umständen Schutzvorrichtungen : - gesichert vor Kurzschluß - gesichert vor Überlastung - gesichert vor Überspannung - gesichert vor Unterspannung (Tiefentladung) Impulse Peak Power Pack Impulse Peak Power Pack Impulse Peak Power Pack Impulse Peak Power Pack...
Page 5
(DCin) Fastons geladen werden. Das Impulse Peak Power Pack darf nicht über den Ausgangsanschlüsse geladen werden. Das Impulse Peak Power Pack kann sehr große Ströme liefern (bis zu 200A für 2 Sekunden). Deshalb muß das Kabel zur Last (z.B. Wohnwagen Mover) auf Ströme von 200A ausgelegt sein.
Impulse Peak Power Pack nicht zu tief zu entladen, weil damit die Lebensdauer der Batterien verkürzt wird. Wenn die Tiefentladung trotzdem aufgetreten ist, wird empfohlen, das Impulse Peak Power Pack so schnell wie möglich wieder zu laden, um den Schaden zu beschränken.
Page 7
6.2 Anschluß Netzadapter (DC in) Am Anschluss (2) kann der mitgelieferte 12Vdc, 1A Netzadapter angeschlossen werden, so dass das Impulse Peak Power Pack mittels Netzspannung geladen werden kann. Der Netzadapter muss an eine Wandsteckdose angeschlossen werden. Impulse Peak Power Pack...
Page 8
(Die externe Drucktaste hat die selben Funktionen wie die interne Drucktaste neben den LEDs.) Wenn die Ausgangsstrom während 15 Minuten niedriger ist als 1 A, wird das Impulse Peak Power Pack automatisch die Ausgangsspannung ausschalten. (Das Ausschalten mittels Drucktaste ist natürlich auch möglich.)
Page 9
EXENDIS B.V. 8. ANZEIGEN Die orange LED zeigt an ob das Impulse Peak Power Pack geladen wird. Die grüne LED zeigt an ob die Ausgangsspannung eingeschaltet worden ist. Orange Grüne Impulse Peak Power Pack ausgeschaltet Ausgangsspannung aus Impulse Peak Power Pack wird entladen.
EXENDIS B.V. *) Wenn der Impulse Peak Power Pack benutzt wird für einen Wohnwagen Mover, ist es wichtig, daß den Mover nicht fester an die Reifen gepresst wird als notwendig. Sonst könnte der Stromverbrauch verdoppelt werden und damit die Fahrzeit halbieren. Auch wenn die Reifen zu weich sind, wird der Mover mehr Strom verbrauchen.
Page 11
The Impulse Peak Power Pack is a Li-ion battery pack with intrinsically safe LiFePO cells and a built in charger. The Impulse Peak Power Pack is a light weight battery pack with a nominal voltage of 12V, that can deliver very high currents, so that it can be used for example for caravan movers, which would otherwise need a large heavy lead-acid battery.
3. SAFETY INSTRUCTIONS Carefully read the manual and the Safety Instructions. The Impulse Peak Power Pack may only be charged by the included power adapter or by the (Dcin) fastons. The Impulse Peak Power Pack may not be charged by the output terminals.
If the Impulse Peak Power Pack is not in use, it must nevertheless be fully charged every 12 months. During winter store, the Impulse Peak Power Pack may be left in the caravan, but must be charged before. Charging overnight is possible.
If you don’t do this and a short circuit occurs, the Impulse Peak Power Pack will not switch off and the wires can blow and/or fire can be caused.
Page 16
An external push button can be connected to the input connection (4a and 4b fastons). This can be useful if the Impulse Peak Power Pack is mounted out of easy reach. This external push button must be normally open.This push button has the same function as the internal push button near the LEDs.
Page 17
If the problem has been solved, the failure indication can be cleared by pushing the push button. *) If the Impulse Peak Power Pack is used for a caravan mover, it is important that the mover is not turned more tighten to the wheels than required. Otherwise the power consumption can be double and the driving time halved.
12.2 Transport by air If the de Impulse Peak Power Pack is transported by air, this may only be done by a person or firm, that has an IATA (Dangerous Goods Regulations) certificate and also has an IATA (Dangerous Goods Regulations) shipping allowance.
Page 19
EXENDIS B.V. GEBRUIKSAANWIJZING Impulse Peak Power Pack U hebt nu de gebruiksaanwijzing voor u, die hoort bij de Impulse Peak Power Pack van EXENDIS B.V. De Impulse Peak Power Pack is een Li-ion pack met intrinsiek veilige LiFePO cellen en een interne lader.
Page 20
: 3 uur 4 uur 4.5 uur 5.5 uur door 30W zonnepaneel onder 3.5 uur 4.5 uur 6 uur 7 uur ideale omstandigheden Impulse Peak Power Pack Impulse Peak Power Pack Impulse Peak Power Pack Impulse Peak Power Pack...
Page 21
(vlakbij de Impulse Peak Power Pack) een extra zekering van een laag amperage plaatsen. De Impulse Peak Power Pack mag niet in serie met een andere Impulse Peak Power Pack (of een andere accu) gebruikt worden (om een hogere spanning te krijgen). De interne schakelelementen en zekering zijn namelijk niet geschikt om de hogere seriespanning af te schakelen bij kortsluiting of overbelasting of diepontlading.
Page 22
De Impulse Peak Power Pack mag niet door kinderen gebruikt worden of door mensen, die daartoe niet bekwaam zijn. Mocht de Impulse Peak Power Pack niet goed werken, dan dient u eerst te noteren welke foutmelding u hebt geconstateerd, voordat u contact opneemt met de service afdeling van uw leverancier/dealer.
Page 23
Als u dit niet zou doen en er ontstaat kortsluiting, zal de Impulse Peak Power Pack niet uitschakelen en de bekabeling zal door kunnen branden en er kan brand ontstaan.
Page 24
6.4 Aansluiting externe dr ukschakelaar Op de aansluiting (4a en 4b fastons) kan een externe drukschakelaar aangesloten worden. Dit kan handig zijn als de Impulse Peak Power Pack op een slecht bereikbare plaats is ingebouwd. Deze extra drukschakelaar moet in ruststand open zijn. Deze drukschakelaar heeft dezelfde functe als de (interne) druktoets naast de LEDs.
Page 25
EXENDIS B.V. 8. INDICATIES De oranje LED geeft aan of de Impulse Peak Power Pack geladen wordt. De groene LED geeft aan of de uitgangsspanning ingeschakeld is. Oranje Groene Impulse Peak Power Pack uit Uitgangsspanning uit Impulse Peak Power Pack wordt ontladen.
EXENDIS B.V. *) Als de Impulse Peak Power Pack gebruikt wordt voor een caravan mover, is het belangrijk om de mover niet strakker op de banden te draaien dan nodig is. Als de mover te strak op de banden gedraaid wordt, kan het stroomverbruik verdubbelen en daardoor de rijtijd halveren! Ook als de banden van de caravan te zacht zijn, zal de mover meer stroom verbruiken.
Need help?
Do you have a question about the Impulse and is the answer not in the manual?
Questions and answers
Hello Why does the 12v supply keep shitting down after 15minutes?
The Exendis Impulse 12V supply may shut down after 15 minutes due to one of several possible failure conditions indicated by LED blink codes. Common reasons include:
- Deep battery discharge (1 blink)
- Battery temperature too high or too low (2 or 3 blinks)
- Electronics temperature too high (4 blinks)
- Output current too high (5 blinks)
- Short circuit (6 or 7 blinks)
- Input voltage too high (8 blinks)
Each condition causes automatic shutdown for protection. The exact reason can be identified by counting the number of LED blinks followed by a pause.
This answer is automatically generated