Summary of Contents for Brunswick led pin light
- Page 1 Installation, Pre-Installation & Operation Manual LED Pin Light December 2012/ 47-902714-000 LED Pin Lighting...
- Page 2 LED Pin Light Installation, Pre-Installation & Operations Manual © December 2012 by the Brunswick Bowling and Billiards Corporation. All rights reserved. GS-Series and Pinball Wizard are registered trademarks of the Brunswick Bowling and Billiards Corporation. 47-902714-000 Reorder Part No. Notice: If available, updates to this manual can be found on-line at www.brunswickbowling.com.
- Page 3 Safety Notes aNd WarNiNg Throughout this publication, “Warnings” and “Cautions” (accompanied by one of the International HAZARD Symbols) are used to alert the mechanic to special instructions concerning a particular service or operation that may be hazardous if performed incorrectly or carelessly. They are defined below. OBSERVE AND READ THEM CAREFULLY! These “Safety Alerts”...
- Page 4 Notice to Users of this MaNUal This manual has been written and published by the Service Department of Brunswick Bowling and Billiards to aid the reader when servicing or installing the products described. It is assumed that these personnel are familiar with, and have been trained in, the servicing or installation procedures of these products, which includes the use of common mechanic’s hand tools and any special...
-
Page 5: Table Of Contents
String Pin Light Brackets ....................17 LED Pin Light MOUNTING ..................... 18 Cabling & Power ....................... 20 Communication CABLES ........................... 20 Addressing ......................... 22 Operation ..............................22 Setting the Address of the LED Pin Light ....................23 LED Pin Lighting... -
Page 6: Packaging
PART NUMBER DESCRIPTION OF PACKAGE 1.00 47-863003-000 PKG. - CONTROLLER FOR PIN DECK LIGHTING, 110V 1.00 47-902714-000 MANUAL - LED PIN LIGHT PRE-INSTALLATION, INSTALLATION & OPERATION Page 1 of 1 MODEL NUMBER CONFIGURATION BRUNSWICK BOWLING & BILLIARDS CORPORATION Drawing Number: G6-300003-000 Rev. - Page 7 Page 1 of 1 MODEL NUMBER CONFIGURATION BRUNSWICK BOWLING & BILLIARDS CORPORATION Drawing Number: G6-300004-000 Rev. No: DESCRIPTION: MNC - PIN DECK LED LIGHTING, HOME RUN CABLE REV. QTY. PART NUMBER DESCRIPTION OF PACKAGE 1.00 47-863005-000 PKG. - DMX CABLE, 150'...
- Page 8 Page 1 of 1 MODEL NUMBER CONFIGURATION BRUNSWICK BOWLING & BILLIARDS CORPORATION Drawing Number: G6-300009-000 Rev. No: DESCRIPTION: MNC - STRING PIN MOUNTING BRACKETS & GUARDS FOR LED PIN LIGHT REV. QTY. PART NUMBER DESCRIPTION OF PACKAGE 1.00 55-860034-000 PKG. STRING PINDECK LIGHT GUARD & MOUNT HDWR.
-
Page 9: Pre-Installation
(4) MIC - Not Used (5) COMMUNICATION INPUT PORT - connection for the communication cable from the deck light controller or the previous led pin light (6) COMMUNICATION OUTPUT PORT - connection for the cable to continue the communication to additional pin lights (7) DIP SWITCH CLUSTER- switches used to set the id address of pinlight. - Page 10 Controller, 47-863003-000 Volts Hertz AC/DC Phase Amps Watts Branch Circuit Customer's Per Unit Responsibility 100-130 50/60 2 wires + ground No more than 12 lights daisy chained in series 200-240 50/60 2 wires + ground No more than 12 lights daisy chained in series (1) POWER SUPPLY SELECTOR SWITCH - Use to select power to controller from the "UsB"...
-
Page 11: Installation Led Pin Lighting
Installation LED Pin Lighting gs-X led PiN light Brackets If the GS-X Pinsetter has an attached wire way on the front of the machine perform step 1, if pinsetter is not equipped with a wire way proceed to step 2. 1. Remove one of the two M8 screws and nuts (Left Hand side of the machine) securing the wire way to the pinsetter. - Page 12 2. Insert the stud of Left Hand Bracket (47-086148-009) into the hole left by hardware removal in previous step and secure it with M8 nut (11-051744-001). Refer to Figure 2. Figure 2 3. Remove the Right Hand side M8 screw and nut securing the wire way to the pinsetter. Refer to Figure LED Pin Lighting...
- Page 13 4. Insert the stud of Right Hand Bracket (47-086149-009) into the hole left by hardware removal in previous step and secure it with M8 nut (11-051744-001). Refer to Figure 3. Figure 3 LED Pin Lighting...
-
Page 14: A-2 Led Pin Light Brackets
PiN light Brackets 1. Find the center of the existing A-2 pin light support. Refer to Figure 4. Figure 4 2. Position 1 bracket (12-610001-000) 20" to the left of the center line of the pin light support and one bracket 20"... - Page 15 Figure 5 3. Thread a 1/4-20 x 1" socket head set screw (11-103171-009) in the nut on the front (toward the foul line) side and tighten to secure the bracket to the pin light support. Refer to Figure 6. LED Pin Lighting...
- Page 16 Figure 6 4. Thread a 1/4-20 hex nut (11-125100-009) onto the set screw and tighten to lock set screw. 5. Thread a 1/4-20 x 1" socket head set screw (11-103171-009) in each of the nuts on top of the bracket. Alternately tighten the set screws until the bracket is square and perpendicular to the pin light support. 6.
-
Page 17: String Pin Light Brackets
striNg PiN light Brackets Figure 7 LED Pin Lighting... -
Page 18: Led Pin Light Mounting
PiN light MoUNtiNg 1. Loosely attach Pin Deck Light to brackets with (1) M6 Screw and (2) External Tooth Lockwashers on each end of the light. Refer to Figure 8. Figure 8 LED Pin Lighting... - Page 19 2. Adjust the angle of the light to the desired position and tighten the screws on both ends of the light. Refer to Figure 9. Figure 9 LED Pin Lighting...
-
Page 20: Cabling & Power
caBliNg & PoWer communication caBles Connect the male end of the 150' (45.72 m) home run cable to the "Communication Output" port on the controller (P/N 47-863003-000). Refer to Figure 10. Figure 10 Connect the female end of the home run cable to the "Communication Input" port on the first LED pin light. - Page 21 3. Using a 10ft/3m cable, connect the first light to the second light, the second light to the third light, etc., until all the lights are chained together. Refer to Figure 11 Figure 11 NOTE: If there is a large gap between two lanes, the data cables can be connected together to create a longer cable. Refer to Figure 12. Figure 12 LED Pin Lighting...
-
Page 22: Addressing
Power 1. Starting at the first or last light, plug the light into a standard electrical outlet. An adapter may need to be used, but the light will support 90-240V 50/60 Hz. Refer to Figure 13. Figure 13 2. Plug the power cable from the light on the next lane into the power plug on the light on the previous lane. Up to 12 lights may be connected together. -
Page 23: Setting The Address Of The Led Pin Light
01 when it is turned on. Refer to Figure 15. Figure 15 setting the address of the led Pin light Each light has 10 dip switches used to create a unique address for the light. Switches 1-9 are used to set the unique address for each light. - Page 24 Set the dip switches as follows: Switch 10 - Switch 10 should always be set to the On position (DMX operation). Switches 1-9 - There are 24 unique addresses (IDs) that can be assigned using dip switches 1-9. The ad- dresses start at 1 and increase by the values of 13 up to an address of 300 (or 24 IDs).
- Page 25 The LED pin light on second lane AND the LED pin light on second from the last lane = 14 (2nd Address) The LED pin light on the third lane AND the LED pin light on third from the last lane = 27 (3rd Address) Continue this address pattern for the remaining lanes.
- Page 26 DIP SWITCH or LED PINLIGHT Lane Address (16) (32) (64) (128) (256) Chart 3 LED Pin Lighting...
Need help?
Do you have a question about the led pin light and is the answer not in the manual?
Questions and answers