Subscribe to Our Youtube Channel
Related Manuals for Mikron Stinger 2
Summary of Contents for Mikron Stinger 2
- Page 1 STINGER 2 User’s Operating Manual ______________________________________________________________________ Made in Bulgaria...
- Page 2 1. Assembling of the device: Assembling the STINGER 2 is simple and you don’t need any special tools. When use the round coil 45cm. or 22x32cm.: The bearing rod is assembled by inserting of the lower part into the upper one. Choose the desired length of the whole construction and the fixing clamp is tightened between both parts of the bearing rod.
- Page 3 In order to avoid interference of the metal parts of the electronic unit, be sure to carry the STINGER 2 on the side of your body that is away from the search frame. The device is switched on through pressing of „ON – OFF / CLEAR“ and you s ee on the display: Start Detector, the serial number of the device and the software version.
- Page 4 "D ISCR ", you hav e to pus h the b utton "VC O / DIS CR", at w hich the device is sw itch ed into dis crimination mode and the display sh ows " NOR MAL DI SCR ". 2.
- Page 5 degree of mineralization of soil. For example, in order to understand how strong is the signal from the soil on a definite location, one can lift the searching coil in the air and the device to be nullified with short pressing of "ON – OFF / CLEAR". Then, the coil is brought close to the ground surface and one can se opposite „Level“...
- Page 6 sound. This is done with change in the parameter "Thresh. For this purpose, through the buttons "◄ and ►" desired value can be selected from „0“ to „20“. The lower the value of „Thresh“, the greater the sensitivity of the device. For instance, if at a balanced device the constant signal from soil is "1"...
- Page 7 shorten the sweeps until you just barely get a response at one spot. The target will be directly below the coil center at this response time – fig.3 fig.3 Upon short pressing of the „MODE“ button, the indications of the discrimination ID1 and ID2 turn on, as well as the intensity of the signal located, in digital or in graphic appearance.
- Page 8 „SELECT“ for 3 sec. 2.2. Setting of the operating parameters in „DISCR“ mode „STINGER 2“ has 2 basic modes of discrimination - „NORMAL DISCR“ and „AUTO DISCR“, which are selected through pressing of button „VCO / DISCR“ as „AUTO DISCR“...
- Page 9 Upon localization of foil, aluminium and unstained iron, ID1 and ID2 have their negative values, and both of them have great positive values express when the nonferrous metal is pure, without admixtures and alloys – gold, bronze, copper, silver. Upon localization of highly stained iron, ID2 has great negative value, for example -15 -20, and the indication of ID1 is around zero or +1, +2.
- Page 10 the symbol „_“. If there is a difference in both levels balance of the device should be performed through „POWER / CLEAR“. In the discrimination modes, with the pressing of „SELECT“, following settings can be selected: „Low tone“ - (1, 2) – 1 is low tone turned off, and 2 is low tone turned on. „olD1“...
- Page 11 is done as follows: the „Auto GEB“ button is pressed and held and to the searching coil a definite type of nonferrous metal is approached, the indicators for the type of metal „ID1“ and „ID2“ show the type of metal and against „accept / ACCEPT“ a definite figure is depicted (as per the type of metal) –...
- Page 12 In the „auto discr“ / „reject“ mode the device memorizes only the purity coefficient ID1 of a metal, and in the “AUTO DISCR“ / „REJECT“ mode it memorizes both coefficients – for purity ID1, and for magnetism ID2. The display shows an indication, for example: „R: -9, -28“...
- Page 13 items or under active stones and highly mineralized soils. In this case, if, for example, an object (stone, ceramics or some iron) has been memorized, with own signal of „-28“, the device will not react to any signals smaller than „-28“, and each signal greater than „-28“...
- Page 14 5.Charging storage batteries and indications for their status. “STINGER 2” has a built-in storage package 14,4V / 2,2Ah, which is able to provide 10- 15 hours of working process without any interruption depending on the chosen power and the type of the used search coil.
- Page 15 “+” and “-” because the use of other chargers or adaptors may lead to irretrievable damages in the batteries! 6. Possible problems during exploitation of “STINGER 2”: 6.1.When switching it on you can not hear a sound, there is no information on the display, no indication that the device is switched on.
- Page 16 is damaged the connection between them will be destroyed and practically the device will be left without power supply. 6.2. The working depth is significantly shallower than the normal. It might indicate for: - storage batteries could be dead – pay attention to the shown % for the capacity of the storage batteries.
- Page 17 Protect the environment and always fill back in the holes you have dugged out! 7. GUARANTEE The detector STINGER 2 is offered with 2 years of guarantee of electronics, labor and materials used, for harms which are not caused on purpose or irresponsibly.
- Page 18 The searching coils and frames are waterproof but the electronics are not, so always prevent any moisture or water from entering the control housing and never allow the cable connector to become submerged in water. If working in or near water, or if there is a possibility of rain, use a protective weather resistant pouch or plastic bag to cover the control housing.
Need help?
Do you have a question about the Stinger 2 and is the answer not in the manual?
Questions and answers