Table of Contents
Advertisement
Quick Links
CVS100
Version 1.2
(Display Software 2.5.2 6031)
Installation and
Operation Guide
Please read this guide carefully before
use and keep it for future reference.
Remember to complete and mail the
owner registration form. (Installer -
Please give this manual to the user of
this product after your use.)
Advertisement
Table of Contents
Summary of Contents for Intec CVS100
- Page 1 CVS100 Version 1.2 (Display Software 2.5.2 6031) Installation and Operation Guide Please read this guide carefully before use and keep it for future reference. Remember to complete and mail the owner registration form. (Installer - Please give this manual to the user of...
-
Page 2: Table Of Contents
..............................14 CREEN ’ ............................15 CREEN NSTALLER TROUBLESHOOTING AND MAINTENANCE .........................16 ................................16 ROUBLESHOOTING .............................16 REVENTATIVE AINTENANCE ................................17 OW TO GET ERVICE ADDITIONAL INFORMATION............................18 ...................................18 ARRANTY INTEC O ..................................18 FFICES ................................19 WNER EGISTRATION © INTEC Video Systems, Inc. Revision F May, 2013... -
Page 3: General Information
INTEC’s products are specifically designed read and understand these instructions carefully. If to enhance vehicle safety. Use of an INTEC display you have any questions or concerns, please do not to view video in any manner other than intended... -
Page 4: Warnings And Cautions
When installing the system be sure use. If they are covered with snow to use only INTEC supplied brackets. and/or ice, it should be cleared off The Car Vision camera must be ®... -
Page 5: Package Contents / Parts List
Part # CVDC6MA Power cable, Part # Power cable, Part # Power cable, Part # CVS100P3M CVS100P3M CVS100MP3M Mounting Hardware, Part # Mounting Hardware, Part # Mounting Hardware, Part # 107-98-02-000 107-98-02-000 107-98-02-000 © INTEC Video Systems, Inc. Revision F May, 2013... -
Page 6: Description
Product Overview Operating Voltage: 12 / 24 VDC (Negative Ground) The CVS100 Series of single camera controllers have been designed to offer the user a wide range Fuse Rating: 2 Amps (Mini Blade) of features and benefits along with a number of installation possibilities. -
Page 7: Installation Instructions
If you have any questions regarding the proper installation or operation of your Car CVS100M Vision® System please call INTEC @ 800-468- 3254 (west) or 800-522-5989 (east) POWER – Using the provided cable connect Wiring Diagram... -
Page 8: Display, Controller And Remote Installation
You may need to purchase additional hardware for your application. 6. Secure the display in the bracket (with the mounting knobs provided) and adjust its positioning 8.27 " as needed. 7.4 8" (CVS100XL from the top.) © INTEC Video Systems, Inc. Revision F May, 2013... -
Page 9: Camera Installation
The CVS100 is equipped with two status LED’s Camera Installation relating to power. One for system power and the For optimum field of view, mount the rear camera other for the 1 Amp radar alarm output. These fuses approximately 10 feet up on the vehicle from ground... -
Page 10: Cable Installation
8) Do not staple through the cable. the cable is exposed is extremely harsh, you can route the cable through a conduit or consult INTEC Periodic checks of the camera system and its wiring about our optional application cable harnesses for... -
Page 11: Connector Alignment
For XL cables with over molded back shells When making a connection, align the arrow on the the arrow with the INTEC logo is inline with the main outer shell of the mating cable connector (seen (top) alignment key. -
Page 12: Image Orientation
- Decreases the value of a menu item. - Selects the external video input. (Must be set to Note: Not all INTEC cameras can be changed in the on before it can be selected). field; some may need to be returned to INTEC to have the image changed. -
Page 13: Radar Operation
(See figure 1) The integrated radar will only operate when connected via an INTEC cable to the camera connector and the system is triggered, via the blue wire, with a +11 to +32 VDC source. (Figure 1) -
Page 14: On-Screen User's Menu
Use the up and down arrow keys to change the value. Resets the user menu back to the factory default. RESET Highlight RST and press <MENU> again to reset. Displays the current software version for your display. © INTEC Video Systems, Inc. Revision F May, 2013... -
Page 15: On-Screen Installer's Menu
Set to STD for standard radar, set to CAN for all others. RADAR 1 Note: Radar 1 connects to the camera input via an Intec cable and is only active when triggered. ALARM Turns the Alarm Output function off and on. Press <Menu> to select the next line item. -
Page 16: Troubleshooting And Maintenance
Check voltage on the red power wire to see if camera is the only way to prevent it from happening sufficient power is reaching the controller. again. The camera should be returned to INTEC for voltage may cause the picture to blur or darken. service. -
Page 17: How To Get Service
The representative will check to see if you tried the in-field adjustments and may offer Products shipped to INTEC without an RMA number alternative solutions for you to try. If these solutions may not be accepted or may result in a delay in don’t work, you may be asked to send some or all of... -
Page 18: Additional Information
Card. Any information you provide on the Card is for INTEC’s internal use only. Our customer list is not sold or given to any other organizations unless required under State or Federal laws. -
Page 19: Owner Registration
® How can we improve our product or service? Mail Registration to: INTEC Video Systems, Inc., 23301 Vista Grande, Laguna Hills, CA 92653. You may also fax it to us at (949) 859-3178 or complete it online by visiting www.intecvideo.com/registration.pdf ©...
Need help?
Do you have a question about the CVS100 and is the answer not in the manual?
Questions and answers