Summary of Contents for RIAN SATSPEEDBOX III R7920
-
Page 1: User Manual
Informationstechnologie-Lösungen Gigabit Ethernet IAD 11n SATSPEEDBOX III R7920 User Manual... -
Page 2: Table Of Contents
Audience ......................4 Introduction ......................5 Overview ......................5 Introduction ....................6 Front Panel LED Indicators & Rear Panels SATSPEEDBOX III R7920 ....6 Introduction ......................7 Package Content ....................7 Hardware Installation ..................8 Port Description: Model SATSPEEDBOX III R7920 ..........8 Quick Start ....................... - Page 3 CE / FCC / RoHS .................... 64 FCC .......................64 FCC Class B Notice ..................64 IC Statement ....................64 EC Declaration of Conformity ................. 64 WEEE – B2C ......................65 Candle Flame .......................66 Warning for users ...................66 SATSPEEDBOX III R7920 Manual Page 3...
-
Page 4: Prefaces
Safety Instructions The most careful attention has been devoted to quality standards in the manufacture of the SATSPEEDBOX III R7920 Gigabit Ethernet IAD. Safety is a major factor in the design of every set. But, safety is your responsibility too. -
Page 5: Introduction
This document describes the usage of SATSPEEDBOX III R7920. Overview SATSPEEDBOX III R7920 is a device that allows several PC or IPTV Set-Top Boxes to connect and to browse the Internet. SATSPEEDBOX III R7920 provides two RJ11 analog interfaces for VoIP calls, PBX, fax machines or any analog telephone. -
Page 6: Introduction
Introduction The SATSPEEDBOX III R7920 Ethernet Gigabit IAD 11n provides a total solution for integrating voice-data network and PSTN. The SATSPEEDBOX III R7920 Ethernet Gigabit IAD 11n supports SIP VoIP Protocol. The SATSPEEDBOX III R7920 Ethernet Gigabit IAD 11n allows 1~2 lines ... -
Page 7: Introduction
Introduction Package Content Please check enclosed product and its accessories before installation. These contents may differ slightly depending on your product version. SATSPEEDBOX III R7920 Ethernet Cable Phone Cable Power Adapter SATSPEEDBOX III R7920 Manual Page 7... -
Page 8: Hardware Installation
Hardware Installation Port Description: Model SATSPEEDBOX III R7920 Port Description POWER Power connector for 12V/1.5A power adapter PHONE1 Phone ports are made to connect analog phones for PHONE 2 VoIP USB interface for SAMBA, Printers and 3G stick LAN(Local Area Connect to PC with Ethernet cable. -
Page 9: Quick Start
5. Connect the other end of the Ethernet cable to your PC’s installed network interface card (NIC). How to configure SATSPEEDBOX III R7920? 1. Configure your PC or NB to the same subnet with SATSPEEDBOX III R7920. 2. Use web browser (IE/Firefox) link to url: http://192.168.1.1... -
Page 10: Wizard Setup
Wizard Setup Wizard for Quick Setup SATSPEEDBOX III R7920 after finishing the authentication, the Main menu will display 2 parts of configuration, please click “Connection wizard” to enter quick start: Pleas connect to the GUI (graphical user interface) with a web browser and following... -
Page 11: Step 3. Time Zone Setup
Three methods are available for Internet Access: Fixed IP User: If you are a leased line user with a fixed IP address, fill out the following items with the information provided by your ISP. SATSPEEDBOX III R7920 Manual Page 11... - Page 12 ISP to see if they use PPPoE. If they do, you need to select this item. PPPoE User Name: Enter User Name provided by your ISP PPPoE Password: Enter Password provided by your ISP. Confirmation Password: Enter Password to confirm again. SATSPEEDBOX III R7920 Manual Page 12...
-
Page 13: Step 6. Wireless Interface Setting
Data Rate: select wireless Data Transfer Rate, default is Auto Associated Clients: click “show active client” button to see the current status for wireless clients SATSPEEDBOX III R7920 Manual Page 13... -
Page 14: Step 7. Voip Setup
SIP Server Domain: you need to input the SIP Domain get from your ISP. User Name: you need to input the Register User Name get from your ISP. Password: you need to input the Register Password get from your ISP. SATSPEEDBOX III R7920 Manual Page 14... -
Page 15: Voip Setup
"public settings". Please select the appropriate option for your specific ISP. For most users, Internet access is the primary application. SATSPEEDBOX III R7920 supports the WAN interface for internet access and remote access. The following sections will explain more details of WAN Port Internet access and broadband access setup. - Page 16 If you are connected to the Internet through a Cable modem line, then a dynamic IP will be assigned. Note: WAN port gets the IP Address, Subnet Mask and default gateway IP address automatically, if DHCP client is successful. SATSPEEDBOX III R7920 Manual Page 16...
- Page 17 Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you need to make sure the following items, PPPoE User name: Enter username provided by your ISP. PPPoE Password: Enter password provided by your ISP. SATSPEEDBOX III R7920 Manual Page 17...
-
Page 18: Broadband
In this page you can create multi wan interface, max for 4 connections, and VLAN TAG is must. SAT Optimization In this page you can select if you want to use internet through satspeed Gateway “compressed” & optimized or not, or only optimized, or complete without any optimization. SATSPEEDBOX III R7920 Manual Page 18... -
Page 19: Lan Interface
When you enable the DHCP server, DHCP Client Range: Enter the starting IP address for the DHCP server’s IP assignment and the ending IP address for the DHCP server’s IP assignment. Client List SATSPEEDBOX III R7920 Manual Page 19... -
Page 20: Ddns
With the SATSPEEDBOX III R7920, you can setup your DDNS service and the device will automatically update your DDNS server every time it receives a different IP address. -
Page 21: Qos
Data couldn’t influence the Voice quality Wireless In an Infrastructure Mode of wireless network, SATSPEEDBOX III R7920 wireless router plays a role as an Access Point (AP) connecting to lots of wireless clients, Stations or WDS. All the wireless clients will share the same Internet connection with other wired hosts via SATSPEEDBOX III R7920 wireless router. -
Page 22: Advanced Setting
Data Rate: select wireless Data Transfer Rate, default is Auto Associated Clients: click “show active client” button to see the current status for wireless clients Multiple AP Multiple AP: support 4 multiple AP Advanced Setting SATSPEEDBOX III R7920 Manual Page 22... -
Page 23: Security
RF Output Power: limitation on WLAN output power, default value 100% Security This page allows you to configure the security of your wireless network. Select different method to have different level of security. SATSPEEDBOX III R7920 Manual Page 23... -
Page 24: Key Length
128-Bit - For 128 bits WEP key, either 13 ASCII characters, or 26 hexadecimal digits Key Format: ASCII: If you are using ASCII characters (case-sensitive). HEX: If you are using hexadecimal numbers (0-9, or A-F). SATSPEEDBOX III R7920 Manual Page 24... -
Page 25: Access Control
MAC Address: Enter the MAC Address of a station that is allowed to access this Access Point. Data Rate: select different Data Rate here Comment: enter characters as a remark Set Security: click this button will pop-up windows to set WDS security SATSPEEDBOX III R7920 Manual Page 25... -
Page 26: Site Survey
The WLAN LED on the router will blink fast when WPS is in progress. It will return to normal condition after two minutes, so you need to setup WPS within two minutes. SATSPEEDBOX III R7920 Manual Page 26... -
Page 27: Sip Setting And "Emergency Routine
This functionality is only working if SIP is configured, and helps to monitor the Satellite Modem synchronisation without traffic consumption, because of monitoring the SIP re-registration. If SIP is not registered, the router takes some actions to get the Satellite Modem synchronisation back. SATSPEEDBOX III R7920 Manual Page 27... -
Page 28: Codec Setting
VoIP Phone is registered to the ISP, you can make a phone call directly. User Name: you need to input the Register Name get from your ISP. Password: you need to input the Register Password get from your ISP. SATSPEEDBOX III R7920 Manual Page 28... -
Page 29: Sip Advance Setting
Media Port Start - The starting range of RTP port. Port number for initial of sending RTP packet, default setting is 9000. SIP Port Number - Assign the SIP port number of SATSPEEDBOX III R7920., default setting is 5060. - Page 30 FAX Option G.711 Fax Pass through: Select this if the SATSPEEDBOX III R7920 should use G.711 to send fax messages. The peer devices must also use G.711. T.38 Fax Relay: Select this if the SATSPEEDBOX III R7920 should send fax messages as UDP packets through IP networks.
- Page 31 Session Timer Enable: Select Enable if you want to define how long the SATSPEEDBOX III R7920 waits to receive a session-alive packet for a voice session from the SIP server. Minimum Expiration Time: Enter the minimum time the SATSPEEDBOX III R7920 waits for a session-alive packet (90-65536 seconds).
- Page 32 DND Always: All incoming call will be blocked until disable this feature. DND Enable: Set a Enable and the SATSPEEDBOX III R7920 will be blocked during the time period. If the “From” time is large than the “To” time, the Block time will from 00:00 to 23:59 When you finished the setting, please click the Submit button.
-
Page 33: Codec Setting
To have the device add a “user=phone” parameter to the SIP URI before sending a SIP INVITE request, select the enable option next Set User Header to Phone. This parameter indicates the user part of the SIP URI (<user>@<sipserver>) the device is calling is a valid telephone number. SATSPEEDBOX III R7920 Manual Page 33... -
Page 34: Tos
RTP TOS Priority Setting: enter the priority for RTP voice transmission. The device creates type of service priority tags; with this priority to RTP traffic that is transmits SATSPEEDBOX III R7920 Manual Page 34... -
Page 35: Telephone
Dialing Parameter Auto Dial Time- If no other number is being dialed within this interval, the SATSPEEDBOX III R7920 will terminate this call. Assign the time interval from 1 to 9 seconds. Off-Hook Alarm Off-Hook Alarm Time - Set has been off-hook, after this time, user will hear ... -
Page 36: Analog Phone
Analog Phone Advanced Setup SATSPEEDBOX III R7920 Manual Page 36... - Page 37 Jitter Buffer Control In SATSPEEDBOX III R7920 VoIP device, the jitter buffer control is a shared data area where voice packets can be stored, collected and sent to the voice shared Buffer in evenly spaced intervals. Modify in packets arrival time, called jitter, can occur because of network congestion, timing drift, or route changes.
- Page 38 Caller ID DTMF END Digit: Set Caller ID DTMF start digit. Hook-Flash Timing Minimum on-hook time default =30 ms Maximum on-hook time default =2000 ms Hot Line This service allows you to make a call to a pre-programmed number by only lifting the handset. SATSPEEDBOX III R7920 Manual Page 38...
-
Page 39: Region
Region Region Setting - Adjust the tone frequency according to each country. Select a country (default is Germany) from the pull-down menu. SATSPEEDBOX III R7920 Manual Page 39... -
Page 40: Phone Book
Phone Book Speed Dial Speed Dial lets you define a button or a set of buttons to link to a specific number defined in Speed Dial list. Position - Select the speed dial shortcut to use from 0 to 9. ... -
Page 41: Dial Plan With Url
“Prefix Number” is the digits that will be added to the beginning of the dialed number. “Destination IP/URL” is the IP address / Domain Name of the destination SATSPEEDBOX III R7920 that owns this phone number. “Destination SIP Port” is port of the destination SATSPEEDBOX III R7920 (Gateway) use.(Default is 5060) -
Page 42: Security
Security Firewall IP Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. ... -
Page 43: Mac Filtering
Mac Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. MAC Enable/Disable –from your local network to Internet through the Gateway ... -
Page 44: Port Filtering
Port Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall. -
Page 45: Dmz
A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network. Typically, the DMZ host contains devices accessible to Internet traffic, such as Web (HTTP) servers, FTP servers, SMTP (e-mail) servers and DNS servers. -
Page 46: Maintenance
Maintenance System Account Setting This page is used to set the account to access the web server of Access Point. Empty user name and password will disable the protection. Time Setting You can maintain the system time by synchronizing with a public time server over the Internet. -
Page 47: Tools
Tools Configuration This page allows you save current settings to a file or reload the settings from the file which was saved previously. Besides, you could reset the current configuration to factory default. Backup: click “Backup” button to save the current configuration of your system to ... -
Page 48: Ping Test
= 30.0/112.5/240.0 ms Restart Restart function let you can restart the SATSPEEDBOX III R7920 device. For some reasons, the device is not responding correctly, if you want to restart the SATSPEEDBOX III R7920, you can just click the Reboot button, than the VoIP equipment will reboot... -
Page 49: Logout
Disable or select the HTTP/FTP protocol of the auto-provisioning feature. If select HTTP or FTP, after key in the server details, the SATSPEEDBOX III R7920 will try to download the configuration files from the provisioning server via HTTP/FTP. The default is disabled. -
Page 50: Tr069
FTP Password: key in FTP Server password File Path: the path of configuration file in your PC Expire Time: The SATSPEEDBOX III R7920 will implement Auto Provision again after expiration time you setup. TR069 TR069 SSL certificates: please browser the SSL certification file and click the ... -
Page 51: Information
Information System Status This page shows the current status and some basic settings of the device. Click System Information to display system status, such as: WAN type, and LAN type, Phone Status, more Status…etc. This page displays the current information of the device. It displays the LAN, ... -
Page 52: Usb Access
USB ACCESS File server Your device let you access to both FAT or NTFS file systems without size limitations. With the samba function inside, you can easily access it over your Windows File Explorer. For this just type the correct IP address (according to your router setting) into the address bar of your Windows file explorer and you will have direct access to the automatic created File_Server folder (see below). -
Page 53: Permanent File Access
Permanent file access If you want to make this access permanent, please follow the steps below: 1. Extras => map network drive 2. Choose a drive letter 3. Use following path for the folder:\\IP_Adress\File server. Please see an example below. 4. -
Page 54: Printer Server
Printer server Printers can easily be connected by following the steps below. Nevertheless, not all printers can be fully supported. Please ask your provider for further details. Installation steps: 1. System control => PRINTERS... - Page 55 Choose network printer Use path \\IP_Address\printers\yourprintername. See example below To find out your printer name you may look up in the Windows file Explorer on the tree for Network environment or you go for the option to LOOK FOR YOUR PRINTER in the picture above! 4.
-
Page 56: Appendix
6. I can’t use web Interface to setting SATSPEEDBOX III R7920, How can I do? A: Please check if your PC connects the SATSPEEDBOX III R7920 LAN port, or PC and SATSPEEDBOX III R7920 with the same Subnet or not. If your PC and SATSPEEDBOX III R7920 don’t at the same Subnet, you can’t Login the SATSPEEDBOX III R7920 Web... -
Page 57: B - Scenario Application
B - Scenario Application:... -
Page 58: Glossary
Glossary - Third Generation network 3G refers to the third generation of mobile telephony technology. The evolution of 3G technology is as follows: 802.11 (b, g, n) A set of WLAN communication standards in the 2.4, 3.6 and 5 GHz frequency bands Access Point A device that allows wireless communication devices to connect to a wireless Network using a standard such as Wi-Fi... - Page 59 IP addresses on the Internet or on local networks that use the TCP/IP protocol. EDGE - Enhanced Data for GSM Environment or Enhanced Data rates for Global Evolution A faster version of GSM wireless service, it allows data to be delivered at rates of 384 Kbps and enable the deliver of multimedia and other broadband applications.
- Page 60 IP address - Internet Protocol address The address of a device attached to an IP network (TCP/IP network) ISP - Internet Service Provider Also referred to as the service carrier, an ISP provides Internet connection service. Kbps - Kilobits per second The rate of data flow.
-
Page 61: Port Number
PDA - Personal Digital Assistant A handheld device used for organization, notes, address books, etc. POP - Post Office Protocol An Internet protocol for retrieving email from a remote server over a TCP/IP connection. Port. A virtual data connection used by programs to exchange data. It is the endpoint in a logical connection. -
Page 62: Virtual Server
RTP - Real-time Transport Protocol A packet format for streaming multimedia over the Internet. SIM - Subscriber Identification Module Found in GSM network technology, the SIM is a card containing identification information for the subscriber and their account. The SIM card can be moved to different devices. SMS -Short Message Service A service for sending short messages of up to 160 (224 in 5-bit mode) characters to mobile devices. - Page 63 VPN - Virtual Private Network A secure private network that runs over the public Internet. Commonly used to connect to an office network from elsewhere. VPN Pass through A feature that allows a client to connect to a VPN server. WAN - Wide Area Network A public network that extends beyond architectural, geographical, or political boundaries (unlike a LAN, which is usually a private network located within a room, building, or other...
-
Page 64: Certifications
Certifications CE / FCC / RoHS This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation. -
Page 65: Weee - B2C
WEEE – B2C All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. The correct disposal and separate collection of your old appliance will help prevent potential negative consequences for the environment and human health. -
Page 66: Candle Flame
Candle Flame Warning for users If the equipment has a candle flame accessible area made of combustible material, users shall be informed about the risks associated with the burning of candles in the user instructions, available with the equipment, or on a warning label. The Information can be in the form of a symbol or in text.