Related Manuals for Vanguard Instruments CBPS-300
Summary of Contents for Vanguard Instruments CBPS-300
- Page 1 OPERATING INSTRUCTIONS for the CBPS-300™ CIRCUIT BREAKER DC POWER SUPPLY Vanguard Instruments Company 1710 Grevillea Court Ontario, California 91761 TEL: (909) 923-9390 April 2003 FAX: (909) 923-9391 Rev 1...
- Page 3 Any deviation from the procedures described in the operator’s manual may create one or more safety hazards, damage the CBPS-300 and the test transformer, or cause errors in the test results. Vanguard Instruments Company, Incorporated assumes no liability for unsafe or improper use of...
-
Page 4: Table Of Contents
1.2 F ..................4 UNCTIONAL ESCRIPTION 1.3 F ..................4 URNISHED CCESSORIES 2.0 CBPS-300 SPECIFICATIONS ................. 5 3.0 CONTROLS and INDICATORS ................6 4.0 PRETEST SETUP....................9 4.1 O .................... 9 PERATING OLTAGES 5.0 OPERATING PROCEDURES................10 5.1 CBPS-300 C ................ - Page 5 List of Tables Table 1.0 CBPS-300 SPECIFICATIONS............... 5 Table 2.0 Functional Descriptions of the CBPS-300 Controls and Indicators....7 Table 2.0 Functional Descriptions of CBPS-300 Controls and Indicators Cont..... 8 List of Figures Figure 1.0 CBPS-300 Controls and Indicators..............6 Figure 2.0 90 to 130Vac Switch Setting................
-
Page 6: Introduction
OPEN or CLOSE breakers from the CBPS- controlled circuit breaker DC power supply. 300 control panel. This device was designed to replace the The CBPS-300 will energize the breaker trip substation batteries during circuit breaker or close coil for one-second duration. This testing. -
Page 7: Cbps-300 Specifications
CBPS-300 OPERATING INSTRUCTIONS 2.0 CBPS-300 SPECIFICATIONS Table 1.0 CBPS-300 SPECIFICATIONS TYPE Special-purpose test equipment, Variable DC Power Supply SIZE (inches) 16.8” wide by 12.6” high by 12”deep (42.6cm x 32 cm x 27cm) WEIGHT 60 pounds (27 Kg) INPUT POWER... -
Page 8: Controls And Indicators
3.0 CONTROLS AND INDICATORS but users should become familiar with them before using the CBPS-300. Accidental CBPS-300 controls and indicators are shown misuse of the controls may damage the in Figure 1.0. The leader line with an index CBPS-300. Users should also be familiar... -
Page 9: Table 2.0 Functional Descriptions Of The Cbps-300 Controls And Indicators
CBPS-300 OPERATING INSTRUCTIONS Table 2.0 Functional Descriptions of the CBPS-300 Controls and Indicators Fig. 1 Panel Markings Functional Descriptions Index OPEN coil voltage positive terminal. Female, NONE Red connector jacks used for connecting voltage test leads. OPEN coil voltage negative terminal. Female,... -
Page 10: Table 2.0 Functional Descriptions Of Cbps-300 Controls And Indicators Cont
CBPS-300 OPERATING INSTRUCTIONS Table 2.0 Functional Descriptions of CBPS-300 Controls and Indicators Cont. Fig. 1 Panel Markings Functional Descriptions Index Voltage control knob. VOLTAGE CONTROL Coil or Motor voltage display selection. COIL/MOTOR Motor voltage initiate switch. Depress switch to MOTOR energize motor. -
Page 11: Pretest Setup
4.1 Operating Voltages Hertz. Voltage selection is set by the 120/240 selector switch as how in Figures The operating voltages for the CBPS-300 2.0 and Figure 3.0. are selectable between 90-130 Volts AC, 50/60 Hertz or 200-240 Volts AC, 50/60 Figure 2.0... -
Page 12: Operating Procedures
CBPS-300 OPERATING INSTRUCTIONS 5.0 OPERATING PROCEDURES 5.1 CBPS-300 Cable connection Before using the CBPS-300, operators A typical connection diagram of the CBPS- should familiarize themselves with the 300 is shown in Figure 3.0. CBPS-300 controls and indicators. Figure 4.0 Typical CBPS-300 Connection Diagram... -
Page 13: General Procedures
Failure to follow this procedure will damage the CBPS-300. b. Turn the voltage control knob to select the desired test voltage. Observe test voltage c. Plug the CBPS-300 power cable into a displayed on the LCD as shown below: power outlet. COIL VLTG: 120.0 V... -
Page 14: Energize Spring Charging Motor Procedure
CBPS-300 test leads. 5.5 Energize Spring Charging Motor 5.6 Remote control Mode Procedure The CBPS-300 can be control by the The following procedures will allow the Vanguard Instrument circuit breaker timers operator to energize circuit breaker charging (CT-6500, CT-7000, CT-7500). The motor. - Page 15 CBPS-300 OPERATING INSTRUCTIONS c. Turn on the CBPS-300. d. Turn the voltage control knob to select the desired test voltage. Observe test voltage displayed on the LCD as shown below: COIL VLTG: 120.0 V NOTE Allow 3 seconds after turning voltage control knob for the voltage display to be stable.
- Page 16 CBPS-300 OPERATING INSTRUCTIONS 1710 Grevillea Court, Ontario, CA 91761, USA Phone: 909-923-9390 Fax: 909-923-9391 Website: http//www.vanguard-instruments.com CBPS-300 04/01/03:...
Need help?
Do you have a question about the CBPS-300 and is the answer not in the manual?
Questions and answers