GE Security NetworX NX-1248E User Manual
  1. Manuals
  2. Brands
  3. GE Security Manuals
  4. Keypad
  5. NetworX NX-1248E
  6. User manual
GE Security NetworX NX-1248E User Manual

GE Security NetworX NX-1248E User Manual

Networx series lcd keypad
Hide thumbs
Table of Contents

Advertisement

Quick Links

GE
Security
NetworX
Series
TM
NX-1248E LCD keypad
User manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NetworX NX-1248E and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for GE Security NetworX NX-1248E

Summary of Contents for GE Security NetworX NX-1248E

  • Page 1 Security NetworX Series NX-1248E LCD keypad User manual...

  • Page 2: Table Of Contents

    ETTING THE SYSTEM CLOCK OFF...................................18 URNING THE DOOR CHIME ............................................18 ALKTEST PARTITIONED SYSTEMS OPERATION ............................19 ..................................19 IGHTS IN PARTITIONING MASTER MODE ...................................20 ISPLAYS IN PARTITIONING MASTER MODE KEYPAD CONTROL TONES (BEEPS)............................22 SERVICE DISPLAY ..................................23 NX-1248E User manual Page 2 16/04/05...
  • Page 3 APPENDIX A – EVENT LOG................................25 APPENDIX B – REFERENCE TABLES ............................26 NX-1248E User manual Page 3 16/04/05...

  • Page 4: Introduction

    AC Power removed to verify the battery is connected and adequately charged. Care should be taken to plug in and restrain the AC transformer after testing. Please read the following information and instructions carefully before operating your security control system. NX-1248E User manual Page 4 16/04/05...

  • Page 5: Glossary Of Terms

    [STAY], or [NIGHT] key on the keypad (for ARMING only) as programmed by the installing company. User Code A four (4) or six (6) digit entry code used to arm or disarm the system. NX-1248E User manual Page 5 16/04/05...

  • Page 6: Keypad Display & Led's

    The NIGHT lighted key will flash when there has been an alarm during the previous arm cycle. or BYPASS Lighted key The BYPASS lighted key is “on” when any zone in this keypad’s partition is bypassed. If the BYPASS lighted key is “off”, no zones are bypassed. NX-1248E User manual Page 6 16/04/05...

  • Page 7: Emergency Activation Keys

    Panic/Hold-Up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring center. Check with your installing company to determine how your security system will respond to the Panic/Hold- Up activation. NX-1248E User manual Page 7 16/04/05...

  • Page 8: Keypad Functions

    If you wish to bypass or unbypass one of these zones, press [BYPASS] while that zone is being displayed. When finished viewing the zones, press [#] to return to the code entry screen. NX-1248E User manual Page 8 16/04/05...

  • Page 9: Arming Your System In The "Stay Mode

    AWAY / STAY / NIGHT modes by pressing the corresponding [AWAY], [STAY], [NIGHT] key twice. This feature is used for ARMING ONLY, and will not disarm the security system. This is ideal for a maid or baby sitter, etc. NX-1248E User manual Page 9 16/04/05...

  • Page 10: Changing Modes While System Armed (Optional)

    NOTE: The abort feature must be enabled. Entering a user code after an alarm report to the central station will send an appending report to the central station after the cancel report. NOTE: The cancel feature must be enabled NX-1248E User manual Page 10 16/04/05...

  • Page 11: Bypassing Zones

    Pressing the [ ] [ ] scroll keys will display all bypassed zones. Press the [#] key to exit this viewing mode. NOTE: All zones will automatically be unbypassed each time the system is disarmed. NX-1248E User manual Page 11 16/04/05...

  • Page 12: Unbypassing

    3 times. Step 5 If another “user code” needs to be programmed, return to Step 3. Step 6 Press the [#] key while the ready light is flashing to exit the User Code Programming Mode. NX-1248E User manual Page 12 16/04/05...

  • Page 13: Assigning User Code Authority Levels

    Press [r] to save the data. The LCD will then prompt you for the next user code. Step 7 If another user code needs to be programmed, return to Step 3. If not, press [#] to exit this feature without saving the data. NX-1248E User manual Page 13 16/04/05...

  • Page 14: Other Keypad Functions

    Alarm Memory Telephone # 1 Telephone # 2 Telephone # 3 Test Display test Light Control English (2) User PIN User Authority Detector Reset Log Review View Settings Set Date/Time BYPASS Walktest AWAY Silent Exit NX-1248E User manual Page 14 16/04/05...

  • Page 15: View Zone Status

    [4] [3] to program/change telephone number 3 Step 3 The LCD display will prompt you for a code. Enter a master code. If the number cannot be changed, the keypad sounder will produde 3 short beeps. NX-1248E User manual Page 15 16/04/05...

  • Page 16: Test Function (Optional)

    The LCD screen will again prompt you to “Select Light Number 0 - 9”. Step 5 Repeat Steps 2 and 3 until complete. Step 6 Press the [#] key to exit from the X-10 menu. NX-1248E User manual Page 16 16/04/05...

  • Page 17: Change Languages

    This screen shows an opening of Partition 3 on September 25th at 5:27 p.m. by user 75. The [r] shows that this event is not programmed to be reported to the central monitoring station. NX-1248E User manual Page 17 16/04/05...

  • Page 18: Adjusting The View/Brightness Of The Lcd

    The door chime feature must be enabled by your installer. The door chime is turned on or off by pressing [r] [1]. Each time [r] [1] is pressed it will toggle the chime feature on/off and produce a momentary ding-dong sound. Walktest Not supported with this keypad NX-1248E User manual Page 18 16/04/05...

  • Page 19: Partitioned Systems Operation

    • SYSTEM READY message will display on the LCD screen if ALL partitions are ready to be armed. • SOUNDER will sound if ANY area has the sounder on. This includes Entry delay, Exit delay, Chime, and Alarm. NX-1248E User manual Page 19 16/04/05...

  • Page 20: Displays In Partitioning Master Mode

    For example: If Area 4 is armed, [r] [4] will disarm Area 4. If Area 4 is disarmed, [r] [4] will arm it. • Press [AWAY], [STAY], or [NIGHT] once to arm all authorized partitions into the corresponding mode. • To control the individual areas, refer to the following section. NX-1248E User manual Page 20 16/04/05...
  • Page 21 If the keypad is sounding an alarm or the siren is running, it can be silenced by entering a code with the authority for the area(s) that are in alarm. NOTE: The [BYPASS], [AWAY], [STAY] and [NIGHT] keys will only work if an individual partition is selected. NX-1248E User manual Page 21 16/04/05...

  • Page 22: Keypad Control Tones (Beeps)

    Entering a valid code will silence the keypad sounder when it is pulsing. The arm/disarm state of your system will not change when entering a code to silence a pulsing keypad sounder. Please contact your installer if a trouble condition exists. NX-1248E User manual Page 22 16/04/05...

  • Page 23: Service Display

    An auxiliary reporting device has failed to communicate. Aux. comm. fail Expansion The main power to an expansion power supply is not on. Power trouble Expansion An expansion power supply has a low battery. Low Battery NX-1248E User manual Page 23 16/04/05...
  • Page 24 A wireless or multiplexed zone device is not reporting to the control. Lost, Press r Press [r] to identify the zone. Zone A zone is experiencing some form of trouble (probably wiring). Trouble, Press r Press [r] to identify the zone. NX-1248E User manual Page 24 16/04/05...
  • Page 25 Service Start Technician is on site. Service End Service End Technician is off site. Code Entry Code Entry A code has been entered. First Open First Open Reports when the first partition is disarmed. NX-1248E User manual Page 25 16/04/05...
  • Page 26 Controls function (action) Entry/exit delay times in seconds : Exit delay time: Secondary Exit delay time: Entry delay time: Secondary Entry delay time: This system is , is not partitioned. This system counts ______ zones NX-1248E User manual Page 26 16/04/05...
  • Page 27 Zone 76 Zone 117 Zone 36 Zone 77 Zone 118 Zone 37 Zone 78 Zone 119 Zone 38 Zone 79 Zone 120 Zone 39 Zone 80 Zone 121 Zone 40 Zone 81 Zone 122 NX-1248E User manual Page 27 16/04/05...
  • Page 28 Zone 164 Zone 187 Zone 142 Zone 165 Zone 188 Zone 143 Zone 166 Zone 189 Zone 144 Zone 167 Zone 190 Zone 145 Zone 168 Zone 191 Zone 146 Zone 169 Zone 192 NX-1248E User manual Page 28 16/04/05...
  • Page 29 www.gesecurity.net EMEA Distribution is a division of GE Security EMEA bvba COPYRIGHT ©2005 © GE Security EMEA bvba. All rights reserved. GE Security EMEA bvba grants the right to reprint this manual for internal use only. GE Security EMEA bvba reserves the right to change information without notice.

Table of Contents