Girl tech RoomBuzz 73034 Instruction Manual

Model 73034
For 1 User / Ages 6 and up
INSTRUCTION MANUAL
P/N 82381700
Now you can have a message center for your
room. Anyone can ring the doorbell and leave up
to three messages. Room Buzz™ is passcode
protected, only your passcode allows you to
access your messages and set product features.
Choose from three cool doorbell sounds.
FEATURES:
MIC
DOORBELL
RECORD
LED
RECORD - Use this button to record messages
and greetings.
DOORBELL - Use this button to ring the door-
bell or select a doorbell sound.
PLAY - Use this button to play and erase mes-
sages.
SET - Use this button to set the passcode,
doorbell and greeting.
NUMBERS 1, 2, 3 - Use any combination of the
three numbers for passcode.
RESET - Use this button to reset Room Buzz™.
Insert a dull, pointed object (like the end of a
paper clip) into the reset button hole. Please
note, if you press reset, it will erase all recorded
messages, greeting and passcode.
MIC - Speak into the mic when recording mes-
sages and greeting.
LED - This red light blinks the number of mes-
sages. If Room Buzz™ is in sleep mode, press
the doorbell button to see the LED light flash the
number of messages.
SETTING UP ROOM BUZZ™
Remove the paper backing from the special tape
on the back of the Room Buzz™, exposing the
adhesive. Next, firmly press Room Buzz™ to the
door.
Rev.B
PLAY
SET
SIDE DOOR
RESET
E
1. SETTING THE PASSCODE - Press the SET
or 1,2,3 buttons and you will be prompted to
record your passcode. Press any of the three
1,2, or 3 buttons to complete your three digit
passcode. Remember you can use any com-
bination of the three numbers. For example:
1,1,1 or 1,2,3 or 2,2,3. You choose. Each time
you press a number, Room Buzz™ will beep
for each number pressed, the fourth beep
completes the passcode.
2. SELECTING A DOORBELL - Toggle through
the doorbell sounds by pressing the doorbell
button. After you hear the doorbell you want,
press the SET button.
3. RECORDING A GREETING - A greeting is
what you want visitors to hear when they
press the doorbell. Room Buzz™ will ask you
to record a greeting. Press and hold the
RECORD button and record a greeting. The
red LED will be lit while recording the greet-
ing. Your greeting will play immediately, if you
like it, press the SET button, if not, press and
hold the RECORD button and re-record a new
greeting. Press the SET button when you are
done, this completes the setup.
PLEASE NOTE: You MUST press SET before
you close the side door to Room Buzz to
keep your settings. If you do not press SET,
the product will remain in set-up phase.
USING ROOM BUZZ™
After Room Buzz™ setup is complete anyone
can leave up to three messages or you can leave
yourself reminder messages.
1. RING THE DOORBELL - Press the doorbell
button to ring the doorbell. If you are in your
room and do not answer the door, press the
doorbell again and Room Buzz™ will play
your recorded greeting for them to leave a
message.
2. LEAVING MESSAGES - Press and hold the
RECORD button to record a message. Once
the message is recorded, the red LED will
flash. The red LED will flash the number of
messages you have.
3. LISTENING TO MESSAGES - The red LED
will flash the number of messages.
1,2,3
Remember, Room Buzz™ has sleep mode
and you will need to press the doorbell button
to see how many messages you have. To lis-
ten to your messages, open the side door and
enter your passcode. Press the PLAY button
to hear all of the messages.
4. ERASING MESSAGES - To erase the mes-
sages, press and hold the PLAY button while
the message is playing. If you want to keep
message one and three but delete message
two, press the PLAY button for message one,
press and hold the PLAY button during mes-
sage two to delete it.
5. CHANGING PASSCODE, DOORBELL AND
GREETING - To change the passcode, door-
bell or greeting enter your current passcode.
Press and hold the SET button then repeat
steps 1-3 under SETTING UP ROOM BUZZ™.
Remember to press the SET button once you
complete the new setup.
SLEEP MODE
Room Buzz™ will go into sleep mode after sixty
seconds of inactivity. To see if there are mes-
sages, press the doorbell once to see the red
LED flash the number of messages.
BATTERY INSTALLATION:
Room Buzz™ is powered by three (3) "AAA"
(LR03) batteries.
• Using a screwdriver, loosen the screw until the
battery compartment door on the back of the
power pack can be removed.
• Insert three (3) AAA (LR03) batteries (we rec-
ommend alkaline) as indicated inside the bat-
tery compartment.