Summary of Contents for Advice ASC-MPPT-3000
- Page 1 User Manual ASC-MPPT-3000 Solar Charge Controller 3KW ADVICE www. .co.il e-mail:advice@advice. co.il...
-
Page 2: Table Of Contents
4.1 Power-Up ....................13 4.2 Operation and Display Panel ................ 13 4.2 LCD Display Icons ..................14 4.3 LCD Setting ....................16 4.4 Reference Code ..................16 5. SPECIFICATIONS ....................17 6. TROUBLE SHOOTING ..................17 ADVICE www. .co.il e-mail:advice@advice. co.il... -
Page 3: About This Manual
10. NEVER cause short circuited on battery output. 11. Warning!! Only qualified service persons are able to service this device. If errors still persist after following troubleshooting table, please send this charger back to local dealer or service center for maintenance. ADVICE www. .co.il e-mail:advice@advice. -
Page 4: Introduction
•Maximum efficiency up to 98% •Battery temperature sensor (BTS) automatically provides temperature compensation •Automatic battery voltage detection •Support wide range of lead-acid batteries including wet, AGM and gel batteries •Integrated intelligent slot compatible with SNMP/MODBUS communication ADVICE www. .co.il e-mail:advice@advice. co.il... -
Page 5: Product Overview
4. Wiring fault indicator 5. Operation button 6. PV connectors 7. Battery connectors 8. Battery voltage sense terminal 9. Remote temperature sensor terminal 10. Wiring box cover 11. Communication port 12. Intelligent slot 13. Grounding terminal ADVICE www. .co.il e-mail:advice@advice. co.il... -
Page 6: Installation
20 cm to the side and approx. 50 cm above and below the unit. The ambient temperature should be between 0°C and 55°C to ensure optimal operation. The recommended installation position is to be adhered to the wall vertically. ADVICE www. .co.il e-mail:advice@advice. co.il... -
Page 7: Power Connection
1.25 x 60 Amps = 75.0 Amps A disconnect is required for the battery and solar circuits to provide a means for removing power from the charger. Double pole switches or breakers are convenient for disconnecting both solar and battery conductors simultaneously. ADVICE www. .co.il e-mail:advice@advice. - Page 8 Be sure that the battery connection is made with correct polarity. Turn on the battery breaker/disconnect and measure the voltage on the open battery wires BEFORE connecting to the controller. Disconnect the battery breaker/disconnect before wiring ADVICE www. .co.il e-mail:advice@advice.
-
Page 9: Grounding And Ground Fault Interruption
Connect the RTS to the 2-pole terminal (see figure as below). The RTS is supplied with 33 ft (10 m) of 22 AWG (0.34 mm2) cable. There is no polarity, so either wire (+ or -) can be connected to either screw terminal. ADVICE www. .co.il e-mail:advice@advice. -
Page 10: Battery Voltage Sense
Be careful to connect the battery positive (+) terminal to the voltage sense positive (+) terminal and battery negative (-) terminal to the voltage sense negative terminal (-). No damage will occur if the polarity is reversed, but the controller cannot read a reversed sense voltage. ADVICE www. .co.il e-mail:advice@advice. -
Page 11: Communication Connections
Intelligent slot allows the controller to use different communication methods except RS232. Slot can support SNMP, USB, MODBUS cards and so on. You can follow the below figure to install the card if you had purchased for it. ADVICE www. .co.il e-mail:advice@advice. - Page 12 Insert bundled software CD into a computer and follow on-screen instruction to install the monitoring software. For the detailed software operation, please check user manual of software inside of CD. ADVICE www. .co.il e-mail:advice@advice. co.il...
-
Page 13: Operation
POWER ON/ Solid On The controller is on. Green CHARGING Flashing The controller is charging. Solid On Fault occurs. FAULT/ WARNING Flashing Warning situation occurs. WIRING FAULT Solid On Battery polarities are not connected correctly. ADVICE www. .co.il e-mail:advice@advice. co.il... -
Page 14: Lcd Display Icons
Input Source Information Indicates the PV input voltage. Configuration Program and Fault Information Indicates the setting programs. Indicates the warning and fault codes. Indicates the current battery type. Output Information Indicate battery voltage. Indicate charging power. ADVICE www. .co.il e-mail:advice@advice. co.il... - Page 15 Constant turns. Voltage The three right bars will be on and mode > 2.167 V/cell the left bar will flash. Floating Batteries are fully 4 bars will be on. mode charged. ADVICE www. .co.il e-mail:advice@advice. co.il...
-
Page 16: Lcd Setting
PV is high loss Battery temperature is too low Battery temperature is too high PV is low loss Output derating caused from high PV voltage Warning Output derating caused from high temperature Low alarm for battery temperature ADVICE www. .co.il e-mail:advice@advice. co.il... -
Page 17: Specifications
Battery temperature your battery ambient temperature. If the problem remains, please contact your too high installer. Check battery wire connection. No display in LCD screen. Push the button, if the problem remains, please contact your installer. ADVICE www. .co.il e-mail:advice@advice. co.il... - Page 18 MPPT 3K Charging Algorithm 3-Step Charging stages Bulk, Absorption, Float Temperature compensation -5 mV / °C / cell (25 °C ref.) coefficient Temperature 0 °C to +50 °C compensation range Temperature Absorption, Float compensated set points ADVICE www. .co.il e-mail:advice@advice. co.il...
- Page 19 Product size (W x H x D, 315 x 165 x 128 Product weight (Kg) Ambient Temperature 0°C to 55°C Range Storage Temperature -40°C to 75°C Humidity 0%-90% RH(No condensing) Enclosure IP31 (indoor & vented) ADVICE www. .co.il e-mail:advice@advice. co.il...
Need help?
Do you have a question about the ASC-MPPT-3000 and is the answer not in the manual?
Questions and answers