Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Holder 2750-AP
Summary of Contents for Holder 2750-AP
- Page 1 Attachment for C250 / C270 C270 C480 / C992 Angle Plow Angle Plow Owner’s Manual Manual And Parts List And Parts List Model #: METEC METAL TECHNOLOGY INC. Reserve all right all right 2750-AP, 2760 AP, 2760-AP 4160-AP, 4172 AP, 4172-AP...
- Page 2 Angle Plow Owner’s Manual and Parts List...
- Page 3 Angle Plow Owner’s Manual and Parts List 2750-AP and 2760-AP Series Angle Plow For HOLDER tractor C250, C270 4160-AP and 4172-AP Series Angle Plow For HOLDER tractor C 480, C992 Page | 1 of 19 Holder Tractors Inc. www.holdertractors.ca...
-
Page 4: Table Of Contents
SCHEDULE..................................10 US to METRIC - METRIC to US CONVERSION ........................ 11 BOLT TORQUE SPECIFICATIONS ............................ 12 PARTS .................................... 13 PLOW PARTS LIST ................................17 PRODUCT WARRANTY REGISTRATION CARD ........................ 18 Page | 2 of 19 Holder Tractors Inc. www.holdertractors.ca... -
Page 5: Understanding The Manual
Refer to the model and serial number when requesting parts or service. Enter your serial number and date of purchase in the space provided below. MODEL NUMBER: ____________________________________________________ SERIAL NUMBER: ____________________________________________________ DATE OF PURCHASE: ____________________________________________________ Page | 3 of 19 Holder Tractors Inc. www.holdertractors.ca... -
Page 6: Safety Information
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. CAUTION: IMPORTANT: Indicates that equipment or property damage could result if instructions are not followed. NOTE: Gives helpful information. Page | 4 of 19 Holder Tractors Inc. www.holdertractors.ca... -
Page 7: Safety Guidelines
9. Always operate the tractor within the manufacturer’s recommended safety guidelines. Operate the tractor at speeds compatible with the working conditions. 10. Inspect the equipment after hitting a solid object to ensure that all aspects of the equipment continue to function properly. Page | 5 of 19 Holder Tractors Inc. www.holdertractors.ca... - Page 8 Your spare parts department should have these in stock. Label Part Location Part name Fig 1 item 1 Warning label Part numbers are in the part list section Figure 1 Page | 6 of 19 Holder Tractors Inc. www.holdertractors.ca...
-
Page 9: Representation Of Labels
Angle Plow Owner’s Manual and Parts List Representation of Labels Figure 2 Page | 7 of 19 Holder Tractors Inc. www.holdertractors.ca... -
Page 10: Installation
1. Grease all grease fittings following each shift, ensuring that all fittings accept grease. Replace any fittings that do not accept grease. Insufficient lubrication will result in premature bearing and sleeve failure. 2. Secure hydraulic hoses to prevent chafing against other parts. Page | 8 of 19 Holder Tractors Inc. www.holdertractors.ca... - Page 11 Angle Plow Owner’s Manual and Parts List MAINTENANCE RECORD Use this log to record maintenance performed on your unit. Date Maintenance Performed Performed by Comments Page | 9 of 19 Holder Tractors Inc. www.holdertractors.ca...
-
Page 12: Schedule
Owner’s Manual and Parts List SCHEDULE PROCEDURE SCHEDULE Before After After Refer When each every each needed tractor hours manual √ √ Hardware - Tighten √ Lubrication Points – Lubricate with high-quality grease. Page | 10 of 19 Holder Tractors Inc. www.holdertractors.ca... -
Page 13: Us To Metric - Metric To Us Conversion
Liters ..........Gallons ........0.264 Kilograms ........Pounds ........2.205 Newton-Meters ......Pound-feet ......0.738 Bar ..........Pounds per Square Inch ..14.50 Kilometers per Hour ....... Miles per Hour ....... 0.621 Page | 11 of 19 Holder Tractors Inc. www.holdertractors.ca... -
Page 14: Bolt Torque Specifications
1-1/8 1430 1-1/4 1105 1975 1-3/8 1500 2650 1-1/2 1775 3200 To determine the torque for a fine-thread bolt, increase rating by 9%. All torques are measured on dry standard bolts. Page | 12 of 19 Holder Tractors Inc. www.holdertractors.ca... -
Page 15: Parts
M-AP-60-001, but for a 72” angle plow it would be M-AP-72-001. Quantities indicated are for 60” angle plow, and may vary for larger or other models. Page | 13 of 19 Holder Tractors Inc. www.holdertractors.ca... - Page 16 Angle Plow Owner’s Manual and Parts List Figure 3 Figure 4 Page | 14 of 19 Holder Tractors Inc. www.holdertractors.ca...
- Page 17 Angle Plow Owner’s Manual and Parts List Figure 5 Figure 6 Page | 15 of 19 Holder Tractors Inc. www.holdertractors.ca...
- Page 18 Angle Plow Owner’s Manual and Parts List Figure 7 Page | 16 of 19 Holder Tractors Inc. www.holdertractors.ca...
-
Page 19: Plow Parts List
27 -- Hydraulic cylinder pin -------------------------------------------- Fig 3 & 6 --- M-AP-XX-207 ----------------- 4 28 -- Cotter pin -------------------------------------------------------------------- O/L --- ----------------------------------- 2 29 -- Spring --------------------------------------------------------------- Fig 3 & 7 --- M-AP-XX-011 ----------------- 2 Page | 17 of 19 Holder Tractors Inc. www.holdertractors.ca... -
Page 20: Product Warranty Registration Card
The procedure to obtain repair under the warranty is to contact the Holder Company of North America. The warranty is void if any part of the equipment is altered or modified in ways. - Page 21 Angle Plow Owner’s Manual and Parts List Holder Tractors Inc. 100 Bay Street, Embrun ON, Canada K0A 1W1 January, 01 2013 Tel: 613-443-3200 Fax: 613-443-9600 Email: info@holdertractors.ca Page | 19 of 19 Holder Tractors Inc. www.holdertractors.ca...
Need help?
Do you have a question about the 2750-AP and is the answer not in the manual?
Questions and answers