1. Manuals
  2. Brands
  3. ATouch Manuals
  4. Touchscreen
  5. 4WR232L
  6. User manual

ATouch 4WR232L User Manual

Atouch 4 wire / 5 wire resistive touchscreen
Hide thumbs
Table of Contents

Advertisement

Quick Links

ATouch User Guide
4 Wire / 5 Wire Resistive Touchscreen

Table of Contents

Introduction ..................................... 3
1.1
1.2
1.2.1 5 Wire Resistive Touch Sensor .......................
1.2.2 5 Wire Resistive Controller ....................... .. .
1.3
1.4
1.5
Touchscreen Installation ...................... 6
2.1
CRT Monitor Installation ................................ 6
2.2
LCD Monitor Installation ................................ 8
Software Driver Installation ................. 11
3.1
3.1.1 Installing the Touch Driver .............................. 11
3.1.2 Uninstalling the Touch Driver ........................... 14
3.1.3 Calibration .................................................. 15
3.1.4 Control Center ............................................. 17
3.2
5 Wire Resistive Touch Screen .......................
Software Drivers .......................... .. .. .. .. .. ..
Agency Approvals ....................................... 5
Warranty ................................................
....................
....................
.........
1
3
3
............
..
4
4
4
5
5
5
11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 4WR232L and is the answer not in the manual?

Questions and answers

Summary of Contents for ATouch 4WR232L

  • Page 1: Table Of Contents

    ATouch User Guide 4 Wire / 5 Wire Resistive Touchscreen Table of Contents Chapter 1 Introduction ………………………………. 3 ……………..… 4 Wire Resistive Touch Screen ……………..… 1.1.1 4 Wire Resistive Touch Sensor ……… ………… 1.1.2 4 Wire Resistive Controller 5 Wire Resistive Touch Screen …………………..
  • Page 2 ATouch User Guide Linux Driver…….…………………………………… 31 Chapter 4 Troubleshooting ……………………….…. 32 Chapter 5 Contact ……………………………………. 33 Appendix Jumper Definition ……………………….. 34...

  • Page 3: Chapter 1 Introduction

    ATouch User Guide Chapter 1 Introduction Thank you for choosing ATouch Touch Screen. It’s our great honor to present the most advanced touch screen to you. This User Guide will lead you through the installation of 4 Wire/ 5 Wire e Resistive. Please follow the instruction and enjoy the technologies with ATouch Touch Screen.

  • Page 4: Wire Resistive Controller

    (any kind of gloves). It is liquid resistance and contamination proof. It works even in bad environment, such as foul, dirt, greasiness. ATouch 5 Wire products are the most reliable available, and have the expected life performance for more than 35 million touches in one location without failure.

  • Page 5: Wire Resistive Controller

    ATouch provides RS-232 and USB interfaces for 5 Wire Controllers. RS-232 controllers are designed two kinds of serial connectors for customers to choose different kinds of serial cables.

  • Page 6: Chapter 2 Touchscreen Installation

    ATouch User Guide Chapter 2 Touchscreen Installation 2.1 CRT Monitor Installation CRT monitor installation process as following steps : 1. Incoming inspection CRT monitor : please check if the monitor works well. Touchscreen : please unpack the touchscreen, connect your touchscreen with the controller on your PC and test if the touchscreen works well.
  • Page 7 4. Sealing Sealing should be even around the front bezel. The material is special sponges from ATouch. The adhesive side of the sponge is stuck on the front bezel, and the special plastic side on the touch sensor.

  • Page 8: Lcd Monitor Installation

    ATouch User Guide 2.2 LCD Monitor Installation 1. Incoming inspection LCD monitor : check if the monitor works well. Touchscreen : Unpack the touchscreen, connect the touchscreen with the controller on your computer and test if the touchscreen works well.
  • Page 9 After this process, check the space between the touchscreen sensor and the front bezel if there is any gape ( You can use the special sponge provided by ATouch to fulfill it). Installing Touchscreen Controller Connect all cables / connectors in the right places and fix the controller at the right position on the monitor rear side metal or plastic case.
  • Page 10 Test if the touch monitor function works well. 4. Sealing Sealing should be even around the front bezel. The material is the special sponges from ATouch. The adhesive side of the sponge is stuck on the front bezel, and the special plastic side on the touch sensor.

  • Page 11: Chapter 3 Software Driver Installation

    3.1.1 Installing the Touch Driver 1. Launch Windows operating system, and exit all Windows programs before continuing with the installation. 2. Insert the ATouch utility diskette into the floppy disk drive. 3. Run “A Touch-2.0.exe”. The following dialog box will appear. Click [Next].
  • Page 12 ATouch User Guide 4. Select Installation Folder and click [Next] to continue the next step. 5. Select Shortcut Folder and click [Next] to continue the next step.
  • Page 13 ATouch User Guide 6. Now the ATouch touchscreen setting is completed. Please check the installation setting. If you accept the setting, please click [Next] to install the driver. 7. After the driver installation, a dialog box will launch for you to choose the serial port which your touch monitor is currently connected to.

  • Page 14: Uninstalling The Touch Driver

    Choose the A Touch 2.0 item. Click the Change/Remove button. Click the Yes button The ATouch driver will be removed. No computer restart is required. 2. Use Shortcut Folder icon in the Start Menu. Click Start, hover over Programs, choose A Touch folder and...

  • Page 15: Calibration

    Calibration button. Click Start, hover over Programs, choose ATouch folder and click Calibration. Click right mouse button on the ATouch icon in the Windows task bar at the bottom right of the display and click the Calibration.
  • Page 16 ATouch User Guide Running the Calibration Program 1. When you run the calibration program using one of the options above, touch the center of the four targets as they appear sequentially. 2. When you release your finger on each point, you will hear a beep.

  • Page 17: Control Center

    Click Start, hover over Programs, choose ATouch folder and click Control Center. Click the ATouch icon in the Windows task bar at the bottom right of the display. Click right mouse button on the ATouch icon in the Windows task bar at the bottom right of the display and click Show Control Center.
  • Page 18 ATouch User Guide 2. Calibrate The Calibrate tab is displayed when the Control Center is launched. Serial port is changeable. Choose the right serial port with which the touchscreen connects, and click Apply button. Click the Calibration button to calibrate.
  • Page 19 ATouch User Guide 3. Settings Mouse Action There are three combinations for this function. Drag Mode and Click on touch Click on touch sends, immediately upon touch, a mouse down/up message at the point of touch on the touchscreen. The user’s finger must be removed from the touchscreen before a...
  • Page 20 ATouch User Guide objects can be dragged on the screen in this mode. Move Mode and Click on touch Click on touch sends, immediately upon touch, a mouse down/up message at the point of touch on the touchscreen. The user’s finger must be removed from the touchscreen before a new touch at any location will be recognized.
  • Page 21 ATouch User Guide When this function is set On, a representation of a typical two-button mouse is displayed in a small window on the desktop, named Right Mouse Button Window (RMBW). The initial presentation of the RMBW shows the left button blue, indicating that the left button is active.
  • Page 22 ATouch User Guide When the mouse cursor is moved to the RMBW and stays on it for five seconds, the RMBW is shutdown automatically. The position of the RMBW is fixed in the bottom right of the display. The RMBW cannot be resized.
  • Page 23 ATouch User Guide 4. Sound Beep Mode The Sound tab sends a single-frequency tone, or “Beep” to the system speaker each time that a valid touch occurs. The beep is enabled by default when the driver is installed. It is able to be turned off by unchecking the Beep on the check box in this tab.
  • Page 24 ATouch User Guide Beep Settings The frequency (Tone) and the Duration of the beep can be adjusted by moving the appropriate slider in this tab with the touchscreen or mouse, or by using the keyboard arrow keys. 5. Diagnostics Choose the right serial port with which the touchscreen connects, and click Apply button.

  • Page 25: Usb Software Driver Installation For Windows

    Windows 95/98/Me/2000/XP/NT The complete procedure is divided into two parts: CP2101 and ATouch-2.0.exe. Step1. Run self-extract file “ATouch USB Drivers.exe” in the driver diskette. Step2: Installing the “CP2101 USB-to-UART Bridge Controller” driver. (Use Windows XP for example) 1. When your operating system is detected a new USB device, please choose the “Install form a list or specific location [Advanced]”...
  • Page 26 ATouch User Guide 2. Please tick the “include this location in the search” item and click the Browse button to specify the correct path of its directory. 3. The Hardware Wizard found the device driver and installing it. 4. After these three steps, the USB touch screen has been activated.
  • Page 27 ATouch User Guide Step3 : Installing the ATouch-2.0 touch screen driver. 1. Execute “ATouch-2.0.exe” in your diskette or other folder, and follow its instructions to complete the installation.
  • Page 28 ATouch User Guide...
  • Page 29 ATouch User Guide 2. Please select the COM3 or COM4 port.

  • Page 30: Linux Driver

    ATouch User Guide 3. Touch each center of the point sequentially. Four calibration points in total. 4. The installation completes. 3.3 Linux Drivers Please contact with your distributor or contact with ATouch Technical Support Dept. (info@a-touch.com.tw)

  • Page 31: Chapter 4 Troubleshooting

    ATouch User Guide Chapter 4 Troubleshooting Before you start troubleshooting, check the following. Make sure your computer and monitor are working normally. Check that the touchscreen connectors are all inserted correctly. Touch location and cursor position are reversed. Calibration is not run during the processes of driver installation.

  • Page 32: Chapter 5 Contact

    Touch position is not accurate. Use the Calibration function of the ATouch Control Center program to re-align. If the touch position is not accurate after the calibration, please check whether the touchscreen driver you use is the newest version.

  • Page 33: Appendix Jumper Definition

    Open Open Open Support Elo driver mode( no support SmartSet) Jump1 Jump2 Jump3 Jump4 Close Close Open Open Support ATouch 2.0 driver mode Jump1 Jump2 Jump3 Jump4 Close Close Open Open Support 3M MicroTouch driver mode(under developing) Jump1 Jump2 Jump3...
  • Page 34 Support Elo driver mode( no support SmartSet) (install CP2101 driver first) Jump1 Jump2 Jump3 Jump4 Close Close Open Open Support ATouch 2.0 driver mode(install CP2101 driver first) Jump1 Jump2 Jump3 Jump4 Close Close Open Open Support 3M MicroTouch driver mode(under developing) (install...
  • Page 35 Support Elo driver mode( no support SmartSet) (install CP2101 driver first). Jump1 Jump2 Jump3 Jump4 Open Close Open Open Support ATouch 2.0 driver mode(install CP2101 driver first). Jump1 Jump2 Jump3 Jump4 Open Close Open Open Support 3M MicroTouch driver mode(under developing) (install CP2101 driver first).

This manual is also suitable for:

5wr232l5wrusbl4wrusbl4wr232s5wr232s

Table of Contents