Related Manuals for Specialised Orthotic Services MoJo CC
Summary of Contents for Specialised Orthotic Services MoJo CC
- Page 1 ® (Complex Care Wheelbase) USER’S MANUAL ALL USER’S OF THE EQUIPMENT SHOULD BE AWARE OF THIS DOCUMENT AND ITS CONTENT ISSUE 1 CLASS 1 DEVICE...
-
Page 2: Table Of Contents
Index CONTENTS PAGE Index Introduction Serial No Brake Variations Stability of Wheelchair and Seating Systems Recommendations on Transport Safety Guidelines for Transportation Transportation 6 - 8 WTORS Manufacturers Key Identification Points 9 & 10 User’s Guide “Preparing Wheelbase For Use” Unfolding the Handles Folding the Handles Attaching &... -
Page 3: Introduction
• make sure that placing a seating system in the wheelbase does not render it unstable, it is recommended that when handing the MoJo CC and seating system over to the client it is tested for stability and a Certificate of Compliance is issued to verify that the level of stability is satisfactory (for more details regarding stability of wheelchair &... -
Page 4: Brake Variations
BRAKE VARIATIONS • Reference is made through out this Users Guide to apply the brakes, the images on those pages show the standard Hand Operated brakes. Please refer to the figures below to identify the correct type of braking system fitted. Standard Attendant Parking Stability of Wheelbase and Seating Systems •... -
Page 5: Recommendations On Transport
SOS Wheelbase & Seating Systems by wheelchair users and carers during transportation. • Specialised Orthotic Services Ltd have carried out extensive investigations into the suitability of our Wheelbases & Special Seating Systems for transportation use and has established clear guidelines for users. -
Page 6: Safety Guidelines For Transportation
General Safety Guidelines for Wheelchair User Transportation • All Wheelchair users should transfer to vehicle seats whenever possible. • Wheelchair is designed to be forward facing when used for transportation of the client in an adapted motor vehicle and users should not travel with the wheelchair at an angle or facing sideways to the direction of travel. -
Page 7: Transportation
Transportation of the user with the seating system can be done when used in conjunction with a Wheelchair Tie down and Occupant Restraint System (W.T.O.R.S.). The MOJO CC wheelbase has been tested using a 4-point tie down system. • Push the wheelchair into the vehicle via a ramp when ever possible. - Page 8 1.2. WHEELCHAIR TIE DOWN SYSTEM • Wheelchair users should not travel in cars, taxis or minibuses, unless the wheelchair is tied down. • Please refer to your Wheelbase & Seating System users guides for information regarding the recommended wheelchair tie down system to be used. •...
- Page 9 1.4. STOWAGE OF THE WHEELBASE AND SEATING SYSTEM • During use of your Special Seating System it may be necessary for you to remove the Seating System and stow this along with the Wheelbase in a vehicle. • is important to realise that these items pose a risk if not adequately restrained whilst in transit.
-
Page 10: Key Identification Points 9
2. KEY IDENTIFICATION POINTS 2.1. STANDARD • SOS MOJO CC Wheelbases are provided either with a fixed or tilting frame (Fig.2.1) and a seating system quick release interface (Fig.2.2 on page 10). Fig.2.1 Tilting Frame Push Handles Handle Adjustment Knob Tilt Base Tilt Lever (Hand operated) Wheelbase Handle Locking Catch Hand brake Interface Location (see page 10) Front Tie Down Point Rear Foot Lever Rear Tie Down Point... - Page 11 Wheelbase is used in conjunction with any retention straps supplied with your seating system. • is recommended that seating systems are attached to the MoJo CC Wheelbase using an SOS “MoJo Wheelbase Seat Interface”. (see tech spec for reference and interface product codes) •...
-
Page 12: Unfolding The Handles
USER GUIDE 1.0 PREPARING THE WHEELBASE FOR USE 1.1. UNFOLDING THE HANDLES • Make sure that both brakes (refer to page 3 for brake type) are applied to the rear wheels (Fig.1.1a). • Pull handle upwards until it is up against the stops (Fig.1.1b). •... -
Page 13: Folding The Handles
1.2. FOLDING THE HANDLES • Make sure that both brakes (refer to page 3 for brake type) are applied to the rear wheels (Fig.1.2a). • Push in locking pin and slide the handle locking catch up & clear or the base uprights (Fig.1.2b). -
Page 14: Attaching & Releasing The Seat
1.3. ATTACHING THE SEAT • Make sure that both brakes (refer to page 3 for brake type) are applied to the rear wheels (Fig.1.3a). • Locate the front of the interface frame into stops as shown (Fig.1.3b). • Lower the interface into the rear catches as shown until it clicks into position (Fig.1.3c). -
Page 15: Tilt Operation (When Fitted)
1.4. TILT OPERATION (when fitted) • Make sure that both brakes (refer to page 3 for brake type) are applied to the rear wheels (Fig.1.4a). • Make sure seating system and user are in place. • Squeeze the tilt lever (Fig.1.4b) and apply your weight to the push handles until desired angle of tilt is achieved then release the lever. -
Page 16: Attendant Parking Brakes (When Fitted)
1.6. ATTENDANT BRAKES (when fitted) • put the brakes on, Squeeze both brake levers (Fig.1.6a) until the brakes are securely on then let go of the lever as this will stay in place. • release the brakes, Squeeze both locking levers under the brake levers (Fig.1.6b) and allow the brake levers to return to the off position, then let go of the locking levers. - Page 17 USER GUIDE 2.0 FITTING AND USE OF ACCESSORIES 2.1. FOOTREST OPERATION (if fitted) • Make sure that both brakes (refer to page 3 for brake type) are applied to the rear wheels (Fig.2.1a). • Locate the footrest stem in the mounting socket (Fig.2.1b), Press the release button and slide footrest fully in until catch engages, release button.
-
Page 18: Swing Aside Footrest Adjustment (If Fitted)
2.2. SWING ASIDE FOOTREST OPERATION (if fitted) • Make sure that both brakes (refer to page 3 for brake type) are applied to the rear wheels (Fig.2.2a). • Hook the footrest assembly on to the location pegs (Fig.2.2b), swing the footrest fully inboard until the catch engages. -
Page 19: Armrest Adjustment (If Fitted)
2.3. ARMREST OPERATION (if fitted) • Make sure that both brakes (refer to page 3 for brake type) are applied to the rear wheels (Fig.2.3a). • Locate the armrest stem in the mounting socket (Fig.2.3b), set the armrest at the required height and tighten the knob (Fig.2.3c). -
Page 20: Sunshade/Rain Canopy Fitting & Removal (If Supplied) 19
2.4. SUNSHADE/RAIN CANOPY FITTING (if supplied) Fitting Sunshade: • Locate the frame legs into the frame receivers (Fig.2.4a), set to height required and tighten in place with wing knob. • Push the centre of the frame locking bar until straight so that the sunshade is tensioned properly (Fig.2.4b). - Page 21 2.4. SUNSHADE/RAIN CANOPY FITTING (if supplied) Cont. Fitting Rain Canopy: • Remove the rain canopy from the zipped pouch on the back of the sunshade (Fig.2.4d). • Unfold the rain canopy and hook over the sunshade as shown (Fig.2.4e). • l the rear panel down between the MoJo handles and hook the front of the rain canopy around the footbox on the seating system (if fitted).
-
Page 22: Solo Rain Canopy Fitting & Removal (If Supplied)
2.5. SOLO RAIN CANOPY FITTING (if supplied) • the two frame clips on to the handle frame either side of the tilt handle (Fig.2.5a). Repeat for other side. Unfold the rain canopy and fix • the two halves of the Velcro straps (at top & bottom) between the two clear panels (Fig.2.5b). -
Page 23: Removing The Client From The Seating System
USER GUIDE 3.0 PLACING THE CLIENT 3.1. PLACING CLIENT INTO SEATING IN WHEELCHAIR • Apply both wheel brakes (refer to page 3 for brake type). • tilt (if fitted) in the required position. • Make sure all client retaining straps are outside of seating system this will avoid the client sitting on them when placed in the seat. -
Page 24: Pushing The Wheelchair
USER GUIDE 4.0 MANOEUVRING THE WHEELCHAIR 4.1. PUSHING THE WHEELCHAIR • Apply both wheel brakes (refer to page 3 for brake type) & make sure client is comfortable/securely seated in the wheelchair (see user guide 3.0). • tilt (if fitted) to suit the clients needs & adjust handle height. •... -
Page 25: Cleaning
USER GUIDE 5.0 LOOKING AFTER THE WHEELCHAIR 5.1. CLEANING • Clean the frame with a damp cloth. • clean the wheels use warm soapy water. 5.2 FAULT FINDING CHECKS • fault finding chart offers possible causes and remedies that can occur over time This depending upon usage. For adjustment and repairs, contact your wheelchair service. Symptoms Pulls or Squeaks... -
Page 26: Maintenance
5.3. MAINTENANCE • Your MoJo CC Wheelbase is designed to require the minimum amount of maintenance, which should only be carried out (along with any repairs) by an authorized repairer. • recommend that, at least once a year, your wheelchair service carry out a thorough inspection and service of your wheelbase. -
Page 27: If You Detect A Fault Or Breakage
REPAIRS & SERVICE Within the warranty period. All MOJO CC wheelbases manufactured by Specialised Orthotic Services Ltd. carry a guarantee on the main frames for 60 months and all other parts for 12 months when used normally. If during this period the product becomes defective and needs repair then please contact SOS (contact details on the back of the booklet). - Page 28 If you require further copies of this handout or require further details relating to any of its content, then please contact us (Copyright applies): Units 127/128, Fauld Industrial Park, Tutbury, Staffordshire. DE13 9HS Tel: 0044 (0)1283 520400 Fax: 0044 (0)1283 520401 E-mail: enquiries@specialorthotic.com Web: www.specialisedorthoticservices.co.uk...
Need help?
Do you have a question about the MoJo CC and is the answer not in the manual?
Questions and answers