Table of Contents
Advertisement
BESTip ATA 20L
VoIP Gateway
User Manual
Projectek Networking Electronics Corp.
Mar. 2009
BESTip ATA 20L User Manual
Copyright Notice
This publication may not be reproduced, in whole or in part,
without prior expressed written permission from Projectek
Networking Electronics Corp. All rights reserved.
Copyright © 2009, by Projectek Networking Electronics Corp.
Projectek Networking Electronics Corp. makes no warranties
with respect to the contents hereof and specifically disclaims
any implied warranties of merchantability or fitness for any
particular purpose. Furthermore, Projectek Networking
Electronics Corp. reserves the right to revise this publication
and to make changes from time to time in the content hereof
without obligation to notify any person or organization of such
revisions or changes.
Trademarks
Projectek Networking Electronics Corp
BESTip. is the trademark of
All other trademaks mentioned herein are the properties of their
respective owners.
Projectek Networking Electronics Corp.
5F-9, No. 16, Lane 609, Sec. 5, Chung Hsin Road,
San Chung, Taipei Hsien, Taiwan, R.O.C.
TEL: (886) 2-2278-7067 Fax: (886) 2-2278-7094
Technical Support: BESTip #: 800123#
http://www.iptelcom.com.tw
ii
.
Advertisement
Table of Contents
Related Manuals for BESTip BESTip ATA 20L
Summary of Contents for BESTip BESTip ATA 20L
- Page 1 This publication may not be reproduced, in whole or in part, without prior expressed written permission from Projectek Networking Electronics Corp. All rights reserved. Copyright © 2009, by Projectek Networking Electronics Corp. BESTip ATA 20L Projectek Networking Electronics Corp. makes no warranties...
-
Page 2: Table Of Contents
BESTip ATA 20L User Manual Please fill in the following ID no. which you can find it on the Table of Contents bottom of your BESTip ATA 20L. You may need it in the future. Chapter 1: Overview ...............5 ... -
Page 3: Chapter 1: Overview
User Friendly The BESTip ATA 20L is a standalone device, and possesses its Reduced Cost of Ownership own processor and network interface. You can easily install... -
Page 4: Physical Description
For further details on these applications, please refer to related devices. The description is listed below (left to right). www.iptelcom.com.tw Physical Description This section provides physical description of BESTip ATA 20L. Front Panel Power There are five buttons on the front panel for quick and easy configuration. -
Page 5: Chapter 2: Installation
Connect the provided network cable into the LAN port of A BESTip ATA 20L BESTip ATA 20L. Connect the other end of the cable to your network eg. a router, hub or an ADSL modem. A DC power adapter Attach the DC power adapter cord into the power ... -
Page 6: Chapter 3: Setup
Chapter 3: Setup menu. After connection, follow the easy instructions to setup the BESTip ATA 20L. You can establish your setup or modify it at any time by launching the BESTip. Be sure the BESTip is well-connected and connect the power adaptor. -
Page 7: Using Buttons To Setup Bestip
BESTip ATA 20L User Manual BESTip ATA 20L User Manual 3. There are four options in the Function Select menu. The options Using Buttons to Setup BESTip will be described in the following sections. You can use the buttons on the front panel of the BESTip and your telephone keypads to setup the BESTip. - Page 8 BESTip ATA 20L User Manual BESTip ATA 20L User Manual 3. Press “DOWN” button to enter “System Setting” menu. 6. You can press “UP” or “DOWN” button to input data, please see the Data Input Sequence below. You can use “NEXT” or “BACK” button to select and erase the value.
- Page 9 BESTip ATA 20L User Manual BESTip ATA 20L User Manual 8. After entering the value, press “OK” button again and the title will 10. It will return to standby status automatically after the configuration stop flashing. The new value has been stored in memory temporarily.
-
Page 10: Function Select－System Info
BESTip ATA 20L User Manual BESTip ATA 20L User Manual 8. ROUTER Adress: It will display the Function Select－System Info Router/ Gateway IP address. You can always get the system information for your BESTip from the System Info menu. 9. Primary DNS Address: It will 1. - Page 11 BESTip ATA 20L User Manual BESTip ATA 20L User Manual IP Policy－DHCP DHCP: Dynamic Host Configuration Protocol is a method for assigning IP address and other IP parameters to computers on the IP network in a single message with great flexibility. IP addresses can be static or temporary depending on the needs of the network.
- Page 12 BESTip ATA 20L User Manual BESTip ATA 20L User Manual IP Policy－Static IP IP Policy－ADSL PPPoE If you select Static IP mode, please consult your ISP or MIS to 1. Press button to enter the have the information listed below. Please use the keypad on Function Select Mode.
- Page 13 BESTip ATA 20L User Manual BESTip ATA 20L User Manual Other Common Setup 6. 2nd IDD Prefix: Please key in the second International Direct Dial After selecting and configuring the IP Policy, you code. This option is needed for need to continue to set the following parameters.
- Page 14 BESTip ATA 20L User Manual BESTip ATA 20L User Manual 13. LCD Contrast: The default Mobile Pincode value is 0. The adjustable range is “Mobile Pincode” function is applied for business purpose. from +5~-10. Customer can buy "Mobile Pincode Card " from our authorized agent and "Mobile Pincode Card"...
-
Page 15: Function Select - Factory Setting
BESTip ATA 20L User Manual BESTip ATA 20L User Manual 5. Press button to save 4. Press to confirm. configuration data in memory Function Select – System Upgrade For mobile pincode usage, caller will hear "beep-beep" tone when calling to the landline connecting to FXO port. It requests To ensure the users to always have the latest Internet caller to enter mobile pincode number. -
Page 16: Chapter 4: To Make An Internet Call
BESTip ATA 20L User Manual BESTip ATA 20L User Manual 5. It will take about 3~5 minutes to Chapter 4: To Make an Internet Call finish downloading depending on the network traffic. If the new software After having finished the setup in Chapter 3, you are ready to version is downloaded successfully, operate your BESTip. -
Page 17: To Make A Bestip-To-Bestip Call
BESTip ATA 20L User Manual BESTip ATA 20L User Manual 2. Once the system testing finishes, 2. Pick up the handset, and you will hear a ready tone. Dial the ID No. of the receiving party and ended with a # key, or you can the screen will display the local time use the phone book to call the receiving party. -
Page 18: To Receive A Bestip Call
BESTip ATA 20L User Manual BESTip ATA 20L User Manual For Domestic Long-Distance Calls Appendix A: Specifications [DDD prefix code] + [Area code + Telephone number] + # Interface For International Calls Telephone Interface RJ-11 ports, 2 x FXS for phone set... -
Page 19: Physical
BESTip ATA 20L User Manual 5 Push Button Switches Operating System Embedded Real-Time Operating System IP, TCP, UDP, DHCP, PPPoE, PAP, Networking Protocol CHAP, DNS Front Panel Configure BESTip ATA through front self-Configuration panel. No additional software or function hardware required...