Table of Contents
Advertisement
Quick Links
SAN REMO
8, 12, 20, Maxi
FREESTANDING
WOOD BURNING
BOILER
STOVES
Installation and Operating
Instructions
Please hand these instructions to the stove user when the installation
is complete. Leave the system ready for operation and instruct the
user in the correct use of the appliance and operation of controls.
Installation – Must be installed by a qualified plumber or suitably
qualified fitter
Revised 11-07-11
Advertisement
Table of Contents
Summary of Contents for San Remo Stoves Maxi
- Page 1 SAN REMO 8, 12, 20, Maxi FREESTANDING WOOD BURNING BOILER STOVES Installation and Operating Instructions Please hand these instructions to the stove user when the installation is complete. Leave the system ready for operation and instruct the user in the correct use of the appliance and operation of controls.
-
Page 2: Technical Specifications
Technical Specifications. Main Dimensions San Remo 8 6” 1” San Remo12 6” 1.5” San Remo 20 6” 1.5” San Remo Maxi 6” 1.5” San Remo 8kW Technical Specifications (Wood) San Remo 12kW San Remo 20kW San Remo Maxi Boiler Boiler Boiler... -
Page 3: Assembly Instructions
It is strongly recommended that this stove is fitted to your heating system by a knowledgeable, experienced and suitably qualified (Hetas or equivalent) plumber or Heating Engineer with experience in fitting boiler stoves. San Remo Stoves cannot accept responsibility for any fault arising through incorrect installation. - Page 4 1. Remove stove from pallet and carefully tip it over onto it’s back. 2. Ensure legs and fixings are present as shown. 3. Ensure the tapped holes, on the base, are free from obstruction. Use a sharp screwdriver to remove any fire cement. Secure the legs and fixings using the screws and washers provided, two screws and two washers per leg.
- Page 5 1. Fit the Flue Collar using the 4-M6 set screws and washers supplied. Screw The M6 nuts on the M6 screws all the way to the end. Then put the washer over the screw/nut assembly and secure the collar to the lid/back as desired. The flue collar is shown below fixed to the top of the stove.
- Page 6 List of Components Door Handle Airwash Control Handle Airwash assembly Primary Air Caps Riddling Handle Ash Pan Ash Pan Tool Coal Catcher Baffle Plate Legs Leg Height Screws M8 Leg Screws M8 Leg Washers M8 Flue Collar Flue Collar Screws M6 Flue Collar Nuts M6 Flue Collar Washers M6 Grate Surround LH...
-
Page 7: Installation Instructions
Installation Instructions READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION These instructions cover the basic principles to ensure satisfactory installation of the stove, although detail may need slight modification to suit particular local site conditions. In all cases the installation must comply with National and European Building Regulations, Local Authority Byelaws and other specifications or regulations as they affect the installation of the stove. - Page 8 Where the chimney is believed to have previously served an open fire installation, it is possible that the higher flue gas temperature from the stove may loosen deposits that were previously firmly adhered, with the consequent risk of flue blockage. It is therefore recommended that the chimney be swept a second time within a month of regular use after installation.
- Page 9 Boiler Connection Revised 11-07-11...
- Page 10 It is strongly recommended that this stove is fitted to your heating system by a knowledgeable, experienced and suitably qualified (Hetas or equivalent) plumber or Heating Engineer with experience in fitting boiler stoves. If fitted incorrectly it could result in serious damage to your home heating system. Plumbing should be carried out in accordance with Relevant Building Regulations and safe practices.
- Page 11 A heat soak radiator of at least 2kW must be used on the same gravity circuit, positioned above the stove. This is used to dissipate heat when the central heating is switched off or the HW cylinder is fully heated. Link Up: On heating and hot water installations, a semi-pumped system should be used to the central heating system with gravity circulation to the hot water cylinder.
-
Page 12: Operating Instructions
Operating Instructions This appliance is not suitable for use in a shared flue. This appliance should not be operated with the doors open. Aerosol Sprays Do not use an aerosol spray on or near the stove when it is alight. Air Controls This stove has been designed to burn clean and efficient. - Page 13 Do not use liquid fuels in this appliance. Size of Fuel Log Length Maximum Log Lengths San Remo 8 Boiler Stove 350mm San Remo 12 Boiler Stove 390mm San Remo 20 Boiler Stove 430mm San Remo Maxi Boiler Stove 430mm Revised 11-07-11...
- Page 14 Lighting the Stove We recommend that you have two or three small fires before you operate your stove to its maximum heat output. This is to allow the paint to cure in steadily and to give a long service life of the paint finish.
-
Page 15: Safety Notes For Your Guidance
Safety Notes for your guidance FIRES CAN BE DANGEROUS – Always use a fireguard in the presence of children, the elderly or the infirm. DO NOT OVERFIRE – it is possible to fire the stove beyond its design capacity, this could damage the stove, so watch for signs of overfiring –... - Page 16 Each stove will have spin valves, which will allow you to easily regulate the heat output. 5 What warranty policy do I get? San Remo Stoves will replace, free of charge, any working part that fails (under normal operating conditions) within 12 months of purchase. Consumables such as glass or stove rope are not guaranteed.