CarShow CS-TUND09 Toyota Tundra Installation Manual

Multi-media navigation system

Advertisement

Quick Links

* JBL Audio equipped vehicles will require additional part # PP-TYJBL1 audio interface
NOTE: Toyota Factory Rear Seat Entertainment CANNOT be controlled via Rosen Multimedia
NOTICE OF INTENDED INSTALLATION AND USE
THE CAR SHOW MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER, WHICH
IS NOT INTENDED FOR VIEWING BY THE DRIVER. THE VIDEO PLAYER IS DISABLED WHEN THE
THE INSTALLER OF THIS PRODUCT MUST INSURE THE VIDEO DISABLE CONNECTION IS
IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH SAFE OPERATION
OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH, AND COULD ALSO
CAR SHOW DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY OR PROPERTY DAMAGE THAT MAY
CarShow
Multi-Media Navigation System Installation Guide
System and audio will come through IR (Infrared) headphones only!
VEHICLE IS IN MOTION THROUGH A CONNECTION TO THE PARKING BRAKE.
WORKING PROPERLY PRIOR TO DELIVERY OF THE VEHICLE.
VIOLATE STATE AND/OR FEDERAL LAW.
RESULT FROM ANY IMPROPER OR UNINTENDED INSTALLATION AND/OR USE.
Do not proceed until process has been completed
CAUTION
Process must be carefully observed in order to reduce
the risk of damage to the accessory or vehicle
Process must be carefully observed in order to ensure a
Specific tools and equipment recommended for this
Observe safe practices, this process can be dangerous
TESTING and TROUBLESHOOTING
Content specific testing and troubleshooting points
Toyota Tundra/Sequoia
Installation Guide
STOP
Damage to the vehicle may occur
CAUTION
CRITICAL
quality installation
TOOLS and EQUIPMENT
process
SAFETY RISK
and there is a risk of personal injury
Copyright 2013 All Rights Reserved
Rev A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CS-TUND09 Toyota Tundra and is the answer not in the manual?

Questions and answers

Summary of Contents for CarShow CS-TUND09 Toyota Tundra

  • Page 1 SAFETY RISK Observe safe practices, this process can be dangerous and there is a risk of personal injury TESTING and TROUBLESHOOTING Content specific testing and troubleshooting points CarShow Copyright 2013 All Rights Reserved Multi-Media Navigation System Installation Guide Rev A...
  • Page 2: Preparing For The Installation

    CarShow Installation Guide - Toyota Tundra/Sequoia PREPARING FOR THE INSTALLATION STEP Before you start, please read these critical steps below BEFORE YOU START THE INSTALLATION, READ THIS GUIDE! CHECK THE BATTERY Test the battery voltage to make sure it’s fully charged This only takes seconds and can save hours of troubleshooting later.
  • Page 3 CarShow Installation Guide - Toyota Tundra/Sequoia REMOVE THE FACTORY RADIO STEP You will need to remove multiple interior trim components prior to removing the factory radio. The following steps will help guide you through this process. Remove Cup Holder Console Carefully remove the Cup Holder’s lower console...
  • Page 4: Electronic Control Unit

    CarShow Installation Guide - Toyota Tundra/Sequoia Remove Mounting Brackets Carefully remove mounting brackets from OEM radio and relocate onto Rosen unit. Be sure to use ROSEN SUPPLIED screws. Piranha System Assembly Instructions STEP This step will walk you through how to attach/connect vehicle-specific faceplate to Electronic Control...
  • Page 5 CarShow Installation Guide - Toyota Tundra/Sequoia Faceplate/ECU Alignment Verify faceplate bracket screw holes are aligned to ECU mounting screw holes. Make sure 28-pin connector is tucked completely inside faceplate cavity as shown at right Mounting Screws Verify faceplate bracket screw holes are aligned to ECU mounting screw holes.
  • Page 6 CarShow Installation Guide - Toyota Tundra/Sequoia Mount the GPS and Sat Radio antenna on the EXTERIOR of the Vehicle Route the GPS harness away from other power harnesses in the vehicle. This will help to ensure optimum performance of the GPS system.
  • Page 7 CarShow Installation Guide - Toyota Tundra/Sequoia Insert a DVD to confirm the Video Disable Circuit is properly Operating. The Brake Wire must be connected to the Park Brake Indicator Wire to complete a ground when the brake is engaged. ENABLE INSTALLER SETTINGS...
  • Page 8 CarShow Installation Guide - Toyota Tundra/Sequoia Select RADIO as the Source Confirm that the AM and FM reception are as expected Troubleshooting 1) Confirm Antenna is properly connected. 2) Reset the System Select SATELLITE RADIO as the Source Troubleshooting 1) Confirm the antenna has unobstructed view of the sky...
  • Page 9: Steering Wheel Controls

    CarShow Installation Guide - Toyota Tundra/Sequoia Select NAV as the Source Confirm the Navigation loads and signal strength is OK Troubleshooting 1) Confirm the antenna has an unobstructed view of the 2) Confirm the antenna is located on the outside of the...
  • Page 10 CarShow Installation Guide - Toyota Tundra/Sequoia Service and Optional Parts List Part Number Description PP-TOY-MAIN Harness, Toyota Main PP-TOY-SWC Harness, Toyota Steering PP-TUND09-3 Installation Guide, Sienna PP1005 Antenna, GPS, 5 meters PP1006 Ground Plate, GPS Antenna PP1007 Harness, Dolby 5.1/Amp...
  • Page 11 CarShow Installation Guide - Toyota Tundra/Sequoia CarShow Copyright 2013 All Rights Reserved Installation Guide CS-TUND09-3 Page 11...

Table of Contents