• The mains valve can cause injury. Do not operate while not plumbed in. • The pump must connect directly to the rainsmart controller not the power point. If the pump is • connected to the power point the pump will run constantly, shortening the life of the pump and potentially running the pump dry.
RAINSMART ‘PUMP BOX’ INSTALLATION GUIDE What is it? ‘Pump Box’ is basically your typical + Pump + RainSmart RainSmart Pump Box all in one, neatly and fully assembled for the ease of you, the consumer. The ‘Pump Box’ is used as a switch between Mains and RainSmart precious Tank water.
The controller must be installed on a vertical surface using the supplied mounting brackets. Install the controller within 2 meters of a protected power supply and no more than 10 meters from the Tank and Float Switch or the Motorised Ball Valve unless extension cables are used. Connect wall mounting clips to RainSmart Control Box using smaller screws provided (SEE FIG.
4. INSTALLING DUAL CHECK VALVE (SEE FIG. 1) The RainSmart comes with 1 x Dual Check Valve. The Dual Check Valve must be installed between the Mains water line and Motorised Ball Valve. The arrow provided on the Dual Check Valve must point towards the Motorised Ball Valve. Therefore the Dual Check Valve male end must be screwed into the Motorised Ball Valve female end.
Page 9
Rainsmart gives you the flexibility of setting a tank water reserve level. A reserve level is a level you set in the tank to signify the point at which the Float Switch is at its lowest point. You can set this reserve level at any height in the tank.
Fit the Motorised Ball Valve to the Mains water pipe downstream from the Dual Check Valve (this should be carried out by a licensed plumber) and plug the valve cable into the RainSmart controller socket (See Quick Setup / Fig.
Page 12
The LED lights are provided to inform you the status of your water usage and they include: Power: When the light is illuminated there is power to the RainSmart controller. In the case power is lost, the Motorised Ball Valve will open to ensure you have at least mains water available to be used for your amenities.
BOX CONTENTS AND TECHNICAL SPECIFICATIONS RainSmart 1 x RainSmart Controller • 1 x Motorised Ball Valve • 1 x Float Switch • 1 x Dual Check Valve • 1 x Plastic Threaded Tee • 1 x Plastic Threaded Nipple •...
This would be defeating the purpose of the purchase of the RainSmart In the unlikely event of a “Pump Failure”, remove power from the RainSmart unit. This will result in automatic “Change Over”...
Power Ok Verify using another appliance (i.e. hairdryer) that the power outlet is operating. If power at outlet and no power on RainSmart , RainSmart may need repairs If NO power at outlet seek advice from a qualified electrician...
Page 18
Verify Pump Outlet Set the mode to pump manual mode o The appliance should turn on If the appliance does not operate, there is a problem with the RainSmart control unit If the appliance turns on, the pressure Pump has failed!
RainSmart 2 Year Product Warranty RainSmart Australia Pty Ltd warrant that, when this product is used for the purpose it was designed, that it will be free of material and manufacturing defects at the time of original purchase. This warranty is limited to the cost of the product and does not cover third party costs including the cost of electricians, plumbers, etc.
Page 20
Physical proof of purchase. The product is to be forwarded by the customer freight paid to an Authorized Rainsmart Australia Pty Ltd service centre. Any service of any product which is found to be faulty due to abuse, fair wear & tear, misuse or improper installation will be charged to the owner at the current hourly service rate.
Page 21
Please attach your sales invoice/docket here as proof of purchase should warranty service be required. Please do not return Warranty – Retain for your records Purchased From ……………………………………………………………………………....Purchase Date …………………… Serial No..…..……..……….. Model No……...…..……... RAINSMART ASUTRALIA PTY LTD Australia Head Office RainSmart Australia Pty Ltd PO Box 835...