Table of Contents
Advertisement
19" LCD Color Monitor
Service
Service
Service
Description
Table of Contents.....................................................1
Revision List................................................................2
Important Safety Notice.............................................3
1. Monitor Specifications................................................4
1.1 Technical Specifications.....................................4
1.2 Physical Specifications......................................5
2. LCD Monitor Description............................................6
3. Operation instructions................................................7
3.1General Instructions...........................................7
3.2 Control buttons...............................................7
3.3 Adjusting the Picture.......................................9
4. Input/Output Specification......................................11
4.1 Input Signal Connector.........................................11
4.2 Factory Preset Display Modes...............................11
4.3 Pixel Defect Policy..........................................12
4.4 Failure Mode of Panel ....................................13
5. Block Diagram.................................................14
5.1 Software Flow Chart.............................................14
5.2 Electrical Block Diagram....................................16
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN
SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Copyright 2008 Philips Consumer Lifestyle
Page
Page
SAFETY NOTICE
Subject to modification ○
191EW9FB/00
191EW9FB/75
191EW9FB/93
191EW9FB/69
191EW9FB/94
191EW9FB/97
191EW9FB/05
191EW9FB/62
Description
6. Schematic Diagram..................................................18
6.1 Main Board......................................................18
6.2 Power Board...............................................22
6.3 Key Board.........................................................24
7. PCB Layout.........................................................25
7.1 Main Board........................................................25
7.2 Power Board...................................................27
7.3 Key Board.........................................................29
8. Wiring Diagram...................................................30
9. Scalar Board Overview........................................31
10. Mechanical Instructions........................................32
11. Repair Flow Chart...............................................36
12. ISP Instructions...........................................................42
13. DDC Instructions.........................................................45
14. White Balance, Luminance Adjustment..................52
15. Monitor Exploded View................................................54
16. Recommended & Spare Parts List............................55
17. Different Parts List ...................................................57
18. General Product Specification...............................60
Sep. 22, 2008
K
Chassis: HUDSON 9
Page
GB
312278518230
Advertisement
Chapters
Table of Contents
Related Manuals for Philips 191EW9FB/00
Summary of Contents for Philips 191EW9FB/00
-
Page 1: Table Of Contents
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES Copyright 2008 Philips Consumer Lifestyle Subject to modification ○ Sep. 22, 2008 312278518230... -
Page 2: Revision List
Update BOM for 191EW9FB/69, 191EW9FB/75, 191EW9FB/93,191EW9FB/97 Oct, 08,2008 Add CTV Model 191EW9FB/05, 191EW9FB/62 Update bezel to Q34G0488AFLC1B0130 for 191EW9FB/62 Nov,11,2008 Add 2nd power code for 191EW9FB/75 and 191EW9FB/93 Add 2nd panel for 191EW9FB/62 and 191EW9FB/94 Dec, 11,2008 Add 2BOM and 12NC for 191EW9FB/00, 191EW9FB/97... -
Page 3: Important Safety Notice
HUDSON 9 Important Safety Notice Proper service and repair is important to the safe, reliable operation of all Philips Company Equipment. The service procedures recommended by Philips and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. -
Page 4: Monitor Specifications
HUDSON 9 1. Monitor Specifications 1.1 Technical Specifications... -
Page 5: Physical Specifications
HUDSON 9 1.2 Physical Specifications... -
Page 6: Lcd Monitor Description
HUDSON 9 2. LCD Monitor Description The LCD monitor will contain a main board, a power board and a key board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage. -
Page 7: Operation Instructions
HUDSON 9 3. Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control buttons are located at the front of the panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected. - Page 8 HUDSON 9 Rear View Kensington anti-thief lock AC power input VGA input...
-
Page 9: Adjusting The Picture
Description of the On Screen Display On-Screen Display is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitor directly throng an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor. - Page 10 HUDSON 9 The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work you way around the different adjustment later on.
-
Page 11: Input/Output Specification
HUDSON 9 4. Input/ Output Specification 4.1 Input Signal Connector Analog connectors Pin No. Description Pin No. Description Red video input DDC +5V Green video input/SOG Logic Ground Blue video input Ground Sense (GND) Serial data line (SDA) Cable detect (GND) H. -
Page 12: Pixel Defect Policy
HUDSON 9 4.3 Pixel Defect Policy MODEL 191EW9 BRIGHT DOT DEFECTS 1 lit sub-pixel 2 adjacent lit sub-pixels 3 adjacent lit sub-pixels (one white pixel) Distance between two bright dot defects* ≧25mm Bright dot defects within 20 mm circle Total bright dot defects of all type BLACK DOT DEFECTS 1 dark sub-pixel 2 adjacent dark sub-pixels... -
Page 13: Failure Mode Of Panel
HUDSON 9 4.4 Failure Mode Of Panel Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical Polarizer has bubbles instruction on this manual to eliminate failure by replace LCD panel. -
Page 14: Block Diagram
HUDSON 9 5. Block Diagram 5.1 Software Flow Chat... - Page 15 HUDSON 9 1) MCU initializes. 2) Is the EPROM blank? 3) Program the EPROM by default values. 4) Get the PWM value of brightness from EPROM. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode.
-
Page 16: Electrical Block Diagram
HUDSON 9 5.2 Electrical Block Diagram 5.2.1 Main Board Panel Interface Crystal 12MHz (CN403) (X401) Scalar IC NT68167FG Keypad Interface EEPROM (Include MCU, ADC, OSD) (CN401) M24C16 (U407) (U401) H sync V sync Flash Memory D-Sub Connector PM25LV010A (U402) (CN101) H_Sync VGA_R+ V_Sync... - Page 17 HUDSON 9 5.2.2 Inverter/Power Board AC input Bridge Rectifier Transformer Rectifier Diodes EMI filter and Filter Start Circuit: R904、R932, R933 CN902 Feedback Circuit Control IC ON/OFF Output MOSFET Transformer Circuit Lamp Over Voltage Feedback ON/OFF Circuit Control Control IC...
-
Page 18: Schematic Diagram
HUDSON 9 6. Schematic 6.1 Main Board 715G3213-1 INPUT R101 100R 1/16W 5% R101 100R 1/16W 5% H_Sync R102 100R 1/16W 5% R102 100R 1/16W 5% HSIN 2 V_Sync R103 100R 1/16W 5% R103 100R 1/16W 5% VSIN 2 R105 R105 R106 R106... - Page 19 HUDSON 9 SCALAR CN401 CN402 VCC3.3 FB407 FB407 ADC_1.8 C401 ADC_2.3 300OHM 300OHM C406 FB404 FB404 VCC3.3 300OHM 300OHM DVDD C407 C408 DVDD ADC_2.3 CVDD_2.3 C409 C439 C439 C433 C433 C442 C442 C406 C406 ADC_1.8 C410 1uF 10V 1uF 10V 0.1uF/16V 0.1uF/16V 1uF 10V...
- Page 20 HUDSON 9 OUTPUT CN405 CN405 PANEL_VCC CN403 CN403 CN403 CN405 PANEL_VCC C419 R434 R434 C420 C420 C420 TCLK1M 220 OHM 1/4W 220 OHM 1/4W 0.1uF/16V 0.1uF/16V C421 TCLK1P R1206 R1206 C441 FB402 Q404 TCLK1P Q405 TCLK1M R415 NC/CONN NC/CONN R433 R434 R435 R436...
- Page 21 HUDSON 9 POWER DSUB_5V CN404 C422 C425 U406 U406 NC/AP1117E33LA NC/AP1117E33LA C426 CN404 CN404 BAT54C BAT54C C427 VOUT D403 D403 D401 D401 C428 5VCC SM240A SM240A D401 D403 Q406 BKLT-VBRI R424 5VCC BKLT-EN R425 C_PANEL_INDEX Volume R426 Volume# 2 Mute R437 VCC3.3 R448...
-
Page 22: Power Board
HUDSON 9 6.2 Power Board 715G2852-2 POWER R918 R918 100 OHM 1/4W 100 OHM 1/4W L904 L904 R919 R919 +12V 1.0uH 1.0uH 100 OHM 1/4W 100 OHM 1/4W C912 C912 ZD902 ZD902 0.001uF 0.001uF C930 C930 RLZ13B RLZ13B R920 R920 C922 C922 R946... - Page 23 HUDSON 9 CN801 CN801 INVERTER CN801 CN802 C839 C839 T801 T801 R821 R821 C801 1500PF/50V 1500PF/50V POWER X'FMR POWER X'FMR R817 R817 1K 1/8W 1K 1/8W CONN CONN C802 10K 1/10W 1% 10K 1/10W 1% R855 R855 D805 D805 C803 15R 1/4W 15R 1/4W LL4148...
-
Page 24: Key Board
HUDSON 9 6.3 Key Board 715G3016-1 CN001 C001 C002 KEY BOARD C003 C004 C005 C006 C007 C008 C009 C010 LED001 A2 R001 R002 R004 R005 R007 SW001 SW002 SW003 SW004 SW005 ZD001 ZD002 LED_RED# LED_GRN# ZD003 ZD004 ZD005 LED001 CN001 R001 4.3K OHM 1% 1/8W LBADC1... -
Page 25: Pcb Layout
HUDSON 9 7. PCB Layout C101 C422 FB404 C4 R408 R441 7.1 Main Board C102 C425 FB405 C4 R409 R442 715G3213-1 C103 C426 FB407 C3 R410 R443 C105 C427 Q404 R414 R444 C106 C428 Q405 R415 R448 C107 C430 Q406 R416 R449 C109... - Page 26 HUDSON 9...
-
Page 27: Power Board
HUDSON 9 7.2 Power Board 715G2852-2 BD901 D4 CN601 D5 IC903 C3 J906 C604 CN602 B5 J601 J907 C801 CN801 A1 J602 J908 C802 CN802 D1 J605 J909 C803 CN803 A1 J801 J910 C900 CN804 D1 J802 J911 C901 CN901 D2 J803 J912 C902... - Page 28 HUDSON 9 C601 C910 IC801 A2 R802 R841 R922 C602 C911 IC901 C3 R803 R850 R923 C603 C912 JR801 A2 R804 R851 R924 C606 C924 JR901 C3 R805 R853 R925 C608 C925 JR902 C3 R806 R854 R926 C609 C928 Q801 R807 R855 R927...
-
Page 29: Key Board
HUDSON 9 7.3 Key Board 715G3016-1 CN001 B5 LED001 B3 SW003 B1 GND1 SW001 B2 SW004 B3 GND2 SW002 B3 SW005 B4 C001 C008 R005 C002 C009 R007 C003 C010 ZD001 B2 C004 R001 ZD002 B4 C005 R002 ZD003 B1 C006 R003 ZD004 B3... -
Page 30: Wiring Diagram
HUDSON 9 8. Wiring Diagram Panel CN902 CN801 30 Pin Power Board CN403 CN404 Main Board CN802 NT68167FG (U401) AC IN CN401 CN101 CN901 D-SUB 6 Pin Key Board CN001... -
Page 31: Scalar Board Overview
HUDSON 9 9. Scalar Board Overview EEPROM Flash ROM DC-DC Converters NOVATEK chip... -
Page 32: Mechanical Instructions
32 32 HUDSON 9 10. Mechanical Instructions Place the monitor face down on a smooth surface .Be careful to avoid scratch and injury during the process of uninstall. Remove the three screws remarked in red to remove the Stand-Base ass'y... - Page 33 HUDSON 9 Remove bezel and rear cover...
- Page 34 34 34 HUDSON 9 4. Remove main frame cover A. Disconnect the two connectors marked in blue B. Remove the two screws marked in red. C. Remove the two screws marked in red.
- Page 35 HUDSON 9 5. Remove power board and main board A. Remove four screws marked in red to remove the Power Board and Main Board from Main Frame. B. Disconnect the connector marked in blue...
-
Page 36: Repair Flow Chart
36 36 HUDSON 9 11. Repair Flow Chart 11.1 Main Board (1). No Power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the Adapter/Inverter section Measure U404 PIN2=3.3V Check C426 and C428... - Page 37 HUDSON 9 (2). No Picture No picture The button if X401 oscillate Replace X401 under control waveform is normal Check reset circuit of Check Correspondent component U401 is normal Measure U404 PIN2=3.3V Replace U401 Check C426 and C428 X401 oscillate waveform is normal Replace X401 Check HS VS from...
- Page 38 38 38 HUDSON 9 (3). White screen White screen Measure Q404 base X401 oscillate waveform is normal is low level? Replace X401 Check Q404, Q4051 is broken or CN403 solder? Check reset circuit of U401 is normal Check Correspondent Check Correspondent component.
- Page 39 HUDSON 9 11.2. Power/Inverter Board (1) No power Check CN902 Pin4, 5 = 5V Check AC line volt 110V or 220V Check AC input Check the voltage of C907 (+) Check bridge rectified circuit and F901 circuit Check start voltage for the pin3 of IC901 Check R904, R932, R933 and Change IC901 Check the auxiliary voltage is bigger than 16V and smaller than 32V...
- Page 40 40 40 HUDSON 9 (2) W / LED, No Backlight Check CN902 Pin4, 5 = 5V Check adapter or MB Check ON/OFF signal Check Main Board Check IC801 PIN12=12V Check R804, Q808 Check IC801 PIN8, 9 or PIN10, 11 have the output of square Change IC801 Check Q809 have the output of square wave at short time.
- Page 41 HUDSON 9 11.3 Key Board OSD is unstable or not working Is Key Pad Board connecting normally? Connect Key Pad Board Replace Button Switch Is Button Switch normally? Replace Key Pad Board Is Key Pad Board normally? Check Main Board...
-
Page 42: Isp Instruction
ISP BOARD x1 b. Printer cablex1 c. VGA cable x1 12.1 Install the “EasyUSB WriterV4.1” 12.2. Connect the ISP board as follow: Connect to Connect to the the PC LPT Philips 191EW9 12.3. The process of ISP write is as follows. - Page 43 HUDSON 9 a) Double-click ，running the program as follows: b) Click icon and the program runs as follows:...
- Page 44 44 44 HUDSON 9 c) Click icon, search the program” Philips_191EW9_NT68167_LM190WH1_20080903_V100”, and click open： d) Click icon. If it burns successfully, it will show as the follow picture:...
-
Page 45: Ddc Instruction
The process of installing “PORT95NT” has been specified in, so it will not be specified again. If you have any problem, please read it. 13.2. Install the “WinDDC_ setup” 13.3. Connect the DDC board as follow: Connect to the PC LPT When you write analog EDID, Connect this port to the Philips 191EW9’s VGA port 12V Input... - Page 46 46 46 HUDSON 9 13.4. Take analog DDC write for example, as follow a. Double-click ，appear as follow Figs：...
- Page 47 HUDSON 9 b. Click c. Key 14 numbers in the Serial Number blank, then click “OK”. Now analog DDC Write completes, as follow. Note: The way of digital DDC write is the same as analog DDC write.
- Page 48 48 48 HUDSON 9 191EW9 EDID Analog 128 bytes EDID Data (Hex): x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF 00 FF FF FF FF FF FF 00 41 0C 2A C0 63 3D 03 00 10: 1F 0D 01 03 6E 29 17 78 2A EE D1 A5 55 48 9B 26 20: 12 50 54 BF EF 80 71 4F 81 CF 01 01 01 01 01 01 30: 01 01 01 01 01 01 66 21 56 AA 51 00 1E 30 46 8F...
- Page 49 Detailed Timing: FD (Monitor limits) Min. V. rate: 56Hz Max. V. rate: 76Hz Min. H. rate: 30 KHz Max. H. rate: 83 KHz Max. Pixel Clock: 170MHz Detailed Timing: FC (Monitor Name) 'Philips 191EW' <-x-Detailed Timing Descriptions-x-> Extension Flag: Checksum:...
- Page 50 50 50 HUDSON 9 Digital 128 bytes EDID Data (Hex): x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF 00 FF FF FF FF FF FF 00 41 0C 2A C0 0B C4 04 00 10: 15 0C 01 03 80 29 17 78 2A EE D1 A5 55 48 9B 26 20: 12 50 54 BF EF 80 71 4F 81 CF 01 01 01 01 01 01 30: 01 01 01 01 01 01 66 21 56 AA 51 00 1E 30 46 8F...
- Page 51 Detailed Timing: FD (Monitor limits) Min. V. rate: 56Hz Max. V. rate: 76Hz Min. H. rate: 30 KHz Max. H. rate: 83 KHz Max. Pixel Clock: 170MHz Detailed Timing: FC (Monitor Name) 'Philips 191EW' <-x-Detailed Timing Descriptions-x-> Extension Flag: Checksum:...
-
Page 52: White Balance, Luminance Adjustment
52 52 HUDSON 9 14. White Balance, Luminance Adjustment 1. Apparatuses and program: analyzer CA-210, PC, tool, FGA adjustment program (PHILIPS 191EW9.DDCI), Pattern generator. 2. Equipment installation: a. Connect analyzer CA-210 to PC by USB connector, install drive program CA-SDK Ver4.00 for CA-210 and restart PC after finish installing. - Page 53 HUDSON 9 4. Color Temp confirmation Connect the signal to the monitor, the monitor display white-picture, use CA-210 to measure the Color Temp of the screen center and select the OSD to make sure whether the Color Temps accord with the SPEC.
-
Page 54: Monitor Exploded View
HUDSON 9 54 54 15. Monitor Exploded View... -
Page 55: Recommended & Spare Parts List
LVDS CABLE 30P-24P 120mm(CMO) 2nd source FQ301 996510015663 089G404A15N IS POWER CORD FQ405 996510019363 Q33G0170AFL 1L0100 KEY PAD FQ205 996510019366 705GQ8CS051 CUSHION ASSY FQ202 996510019631 Q44G8009813 2A 18.5 PHILIPS LCD CARTON FQ202 996510020579 Q44G8009813 2B 18.5 LCD PHILIPS CARTON(CMO) 2nd source... - Page 56 056G 662 13 IC AZC099-04S SOT23-6L U103 996510014826 056G 662 13 IC AZC099-04S SOT23-6L Service Kit Description Part No. Philips 12NC Remark DDC KIT 715L2005C2 9965 000 43197 FOR ALL MODEL OSD SN KIT 715GT033 C 9965 000 43252 FOR ALL MODEL...
-
Page 57: Different Parts List
HUDSON 9 17. Different Parts List Diversity of 191EW9FB/75 compared with 191EW9FB/00 191EW9FB/75 191EW9FB/00 Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description FQ301 996510016841 089G412A15NIS3 POWER CORD 996510015663 089G404A15N IS POWER CORD FQ301 996500037345 089G412A18NIS3 POWER CORD... - Page 58 HUDSON 9 58 58 Diversity of 191EW9FB/94 compared with 191EW9FB/00 191EW9FB/94 191EW9FB/00 Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description FQ301 996510015866 089G417A15N IS POWER CORD 996510015663 089G404A15N IS POWER CORD PANEL LM185WH1-TLA1 PANEL LM185WH1-TLA1 FQ001 996510019925...
- Page 59 HUDSON 9 Diversity of 191EW9FB/05 compared with 191EW9FB/00 191EW9FB/05 191EW9FB/00 Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description FQ301 089G410A15N IS POWER CORD 089G404A15N IS POWER CORD PANEL LM185WH1-TLA1 PANEL LM190WH1-TLA1 FQ001 750GLG185W1A12N000 750GLG185H1A12N000 NJ LGD NJ LGD...
-
Page 60: General Product Specification
PROE FILES REQUIRED 5.3 LOCATION OF PHILIPS LOGO PER PHILIPS MAKE-UP SHEET 5.4 GAP BETWEEN PANEL AND FRONT BEZEL <1.0MM 5.5 LOCATION OF CONTROL ICONS- PER PHILIPS GRAPHIC SHEET 5.6 COLOR FOR RESIN/PAINT PER PHILIPS MAKE-UP SHEET 5.7 RESINS 5.8 IF RAINT IS USED 5.9 PLASITIC MOLD TOOLING... - Page 61 HUDSON 9 5.17 PALLET / CONTAINER LOADING (REFER TO PHILIPS APPROVED SHT 560) 6. ENVIRONMENTAL CHARACTERISTICS 6.1 SUSCEPTIBILITY OF DISPLAY TO EXTERNAL ENVIRONMENT 6.2 TRANSPORTATION TESTS 6.3 DISPLAY DISTURBANCES FROM EXTERNAL ENVIRONMENT 6.4 DISPLAY DISTURBANCES TO EXTERNAL ENVIRONMENT 7. RELIABILITY 7.1 MEAN TIME BETWEEN FAILURES...
-
Page 62: Foreword
30 minutes that brightness stability is optimal, and follow strictly after panel specification. 2. PRODUCT PROFILE This display monitor unit is a color display monitor enclosed in PHILIPS styling cabinet which has an integrated tilt base. 2.1 LCD Tier 1: LGD 2.1.1... -
Page 63: Electrical Characteristics
HUDSON 9 3. Electrical characteristics 3.1 Interface signals 1). D-Sub Analog Input signal: Video, Hsync, Vsync Video: 0.7 Vp-p, input impedance, 75 ohm @DC Sync. Separate sync TTL level, input impedance 2.2k ohm terminate Hsync Positive/Negative Vsync Positive/Negative Composite sync TTL level, input impedance 2.2k ohm terminate (Positive/Negative) Sync on green video 0.3 Vp-p Negative (Video 0.7 Vp-p Positive) 3.2 Interface... - Page 64 64 64 HUDSON 9 3.2.2 Software control functions via OSD /control adjustable functions: Please refer to following Hudson8 OSD definitions Reset - No: Exit Yes: Auto adjustment for displaying timing mode and recall factory preset OSD Tree Level 1 Level 2 Level 3 Default Picture...
-
Page 65: Timing Requirement
HUDSON 9 3.3 Timing requirement Factory Preset mode definition: Perfect FOS while presenting all required timings. Required timings need to be specified in User’s Manual. User mode Can be showed (not over scalar or Panel spec.) It needs to reserve the 22 timings space in memory size. 3.3.1 Mode storing capacity Factory preset modes : 10... -
Page 66: Horizontal Scanning
In accordance with VESA Display Channel Standard Ver.1.0 and DDC 2B capability 3.9 DDC/CI Support In accordance with VESA DDC/CI and MCCS ver.2.0, the monitor should be workable with Philips Smart Manage, Smart Control II V1.2, and Portrait Display Tune at least. -
Page 67: Hot-Key Definition
HUDSON 9 3.12 Hot-key definition Key Press Item OSD Message Time Timeout Monitor controls locked Monitor Controls 6 sec 5 sec ［Menu］ Lock Monitor controls unlocked（default） Factory Mode [AUTO]+[Menu]+[Power] DDC/CI On/OFF DDC/CI ON (default) [MENU]+[DOWN] 5 sec 5 sec for VISTA DDC/CI OFF 4. -
Page 68: White Color Adjustment
5.1 Cosmetic - Philips ID 5.2 Mechanical data files - ProE files required 5.3 Location of Philips logo - Per Philips make-up sheet 5.4 Gap between panel and front bezel < 0.8 mm (typ) 5.5 Location of Control icons - Per Philips Graphic sheet 5.6 Color for resin/paint -... -
Page 69: Texture/Glossing Of Housing
HUDSON 9 5.11 Texture/Glossing of housing The texture area and texture no should follow Philips make-up sheet. The exterior surfaces shall have a uniform texture. Philips must approve the mold texturing. Detail document for texture refer to “UN-D249”, “UN-D 600”. -
Page 70: Pallet / Container Loading (Refer To Philips Approved Sht 560)
70 70 HUDSON 9 5.15 Product dimension / Weight (Refer to Philips approved SHT 191) Unit dimension : 439(w)*363(H)*191(D) Packed unit dimension : 490(w)*375(D)*145(H) Net weight : 3.98Kg Gross weight : 4.95Kg. 5.16 Transportation Transportation standards follow TPV standard. 5.16.1 Transportation packages Packaging and wrapping shall be sufficient to protect the product against damage or loss during shipment from the supplier to the destination specified in the purchase order. -
Page 71: Transportation Tests
HUDSON 9 6.2 Transportation tests Refer to 5.15.2 6.3 Display disturbances from external environment According to IEC 801-2 for ESD disturbances 6.4 Display disturbances to external environment 7. Reliability 7.1 Mean Time between Failures System MTBF (Including the LCD panel and CCFL): Refer to 2.1 panel MTBF 8. -
Page 72: Philips' Flat Panel Monitors Pixel Defect Policy
72 72 HUDSON 9 9. Philips’ Flat Panel Monitors Pixel Defect Policy Philips’ Flat Panel Monitors Pixel Defect Policy BRIGHT DOT DEFECTS ACCEPTABLE LEVEL MODEL 191EW9 1 lit sub-pixel 2 adjacent lit sub-pixels 3 adjacent lit sub-pixels (one white pixel) - Page 73 HUDSON 9 Fig 1: Measurement locations of Brightness Uniformity Fig 2: Cross talk pattern Gray level 46 (64 Gray level) Fig 3: Cross talk Pattern Center at Gray level 0 (Black)
-
Page 74: Regulatory Compliance
HUDSON 9 74 74 10. REGULATORY COMPLIANCE 10.1 Worldwide Regulatory REGION COUNTRY REFERENCE DOMAIN SAFETY / EMC / ERGONOMICS / STANDARDS DOCUMENTS (RSO) (NSO) LOGO IEC60950-1:2001. Group and national differences World wide World wide CB Report, certificate of all countries listed in CB Bulletin No. 107A European Low Voltage Directives 73/23/EEC and Declaration of Conformity Europe... - Page 75 HUDSON 9 TCO'06 TCO report and certificate EN60950-1:2001 S+ PZ1 certificate EN55020,EN55024, Switzerland S+ PZ1 certificate IEC61000-3-2 ,IEC61000-3-3 EMF EN 50392 EN 50392 report EN60950-1:2001 Certificate of Conformity Eastern Europe EN55022,EN55024, Certificate of Conformity IEC61000-3-2 ,IEC61000-3-3 RUSSIA GOST R 50377-1992 GOST certificate ISRAEL IS 1121, IEC60950/IEC60950-1...
- Page 76 HUDSON 9 76 76 CNS-14336 (IEC 60950-1) BSMI certificate TAIWAN CNS-13438 (CISPR22) Class B BSMI certificate Criteria 18 ( Monitor ) ( LCD ) GreenMark / certificate AUSTRALIA/ AS/NZS3548:1995 CB, EMC report NEW-ZEALAND AS/NZS CISPR22: 2002 Class B Saudi Arabia EN60950-1:2001 SASO Saudi Arabia...
- Page 77 HUDSON 9 MEXICO NOM-019-SCFI-1994 NOM certificate Argentina EN60950-1:2001 TUV S-mark or IRAM UL 60950-1: 2003 UL certificate or cUL FCC Part 15 Class B FCC report and DoC LATAM Energy Star EPA test data Brazil TCO'99 TCO report and certificate TCO'03 TCO report and certificate TCO'06...
-
Page 78: Emc Requirements
10.2 EMC Requirements Supplier DVT EMI test result must be submitted prior to DVT samples delivery, and PVT EMI test result must be submitted again prior to PVT samples delivery, which also has to meet Philips' immunity testing specification. 10.3 ROHS Restriction on the use of certain hazardous substances. - Page 79 4. When the HV circuitry is operating properly there is no possibility of an x- tube must be the same type as the original, including suffix letter, or a Philips radiation problem. High voltage should always be kept at the manufacturer's approved type.