Page 3
Thank you! Mail to: documentation@teracue.com All information within this document is confidential to Teracue eyevis GmbH costumers and should not be copied or distributed to non Teracue eyevis GmbH customers. All Teracue products and all of its components are registered trademarks RADEMARKS licensed to Teracue eyevis GmbH.
Page 4
User Guide V1.2 Information about the manual This manual is designed to help administrators and users to install the DMM-Series on their computer. If you received this publication as a PDF, then it's a good idea to print it out for future reference.
Overview Characteristics DMM-Series is a compact modular digital TV head end that includes professional MPEG-2 and H.264 SD/HD IRD, MPEG-2 and H.264 SD/HD, Re-Multiplexer, QAM/COFDM Trans-Modulator, DVB Scrambler. Within 19” 4RU chassis, it provides 8 slots for any type of modules with redundant power supply.
DMM-Series User Guide V1.2 1.5 DMM-140 Series Professional MPEG-2 SD IRD and Processor Module Multiple inputs DVB-S2/S/C/T, TS/IP and ASI SD MPEG-2 MP@ML digital video decoding Flexible built-in re-multiplexing between ASI, Tuner and TS/IP Inputs 2x DVB-CI slots, multi programs, BISS-1 and BISS-E decryption...
DMM-Series User Guide V1.2 Control with Display and Keypad DMM-150 Series Main-Menu Sub-Menu Description ASI: Display ASI input status Status TUNER: Display tuner input status IP IN: Display IP input status LNB Frequency: Input LNB frequency Satellite Frequency: Input downstream frequency of satellite...
Page 9
DMM-Series User Guide V1.2 Main-Menu Sub-Menu Description Biss Mode: Set Biss mode, can select ‘OFF’, ‘Biss E’ or ‘Biss 1’ Biss 1 Setup: Set Biss 1 (password is required) BISS Menu Biss E Setup: Set Biss E (ID number and password are required)
Page 10
DMM-Series User Guide V1.2 TS ID: 1~65535 Program List: Select program. Output Bit Rate: Display Output bit rate Stream IP Addr: 1.0.0.1~223.255.255.254 Stream Netmask: 1.0.0.1~223.255.255.254 and 0.0.0.0 Stream Gateway: 1.0.0.1~223.255.255.254 224.0.0.0~239.255.255.255 Stream Mac address: Display factory-Set Mac addresses Gateway Mac address: Edit Gateway Mac address Multicast IP Addr: Enter the IP address of the Multicast Stream for the transport Stream over IP.
DMM-Series User Guide V1.2 DMM-140 Series Main-Menu Sub-Menu Description ASI: Display ASI input status Status TUNER: Display tuner input status IP IN: Display IP input status LNB Local Oscillator (L.O.) Freq: enter the frequency of the LNB in MHz. Satellite Freq: edit the satellite down link frequency in MHz. The IF frequency will be calculated automatically.
Page 12
DMM-Series User Guide V1.2 Biss: It includes Biss Mode, Biss 1 Setup and Biss E Setup Biss Mode: Set Biss mode, can select ‘OFF’, ‘Biss E’ or ‘Biss 1’ Biss 1 Setup: set Biss 1 (password is required) Biss E Setup: set Biss E (ID number and password are...
Page 13
DMM-Series User Guide V1.2 Main-Menu Sub-Menu Description Stream IP Addr: 1.0.0.1~223.255.255.254 Stream Netmask: 1.0.0.1~223.255.255.254 and 0.0.0.0 Local Setup Stream Gateway: 1.0.0.1~223.255.255.254 224.0.0.0~239.255.255.255 MAC Address: Display MAC Address Trap IP Addr Trap IP Addr: 0.0.0.0~255.255.255.255 Unit Name Edit U\unit name Main Version...
DMM-Series User Guide V1.2 Control with web server To control the unit via Web server, type in the unit IP address in the web browser. Default username and password are as following. Username: root Password: 12345 DMM-150 Decoder Module 3.1.1...
DMM-Series User Guide V1.2 Input Status ASI: ASI input status Total Bitrate: Total bitrate of ASI input Packet size: ASI input Packet size Valid Bitrate: Valid bitrate of ASI input Tuner: Tuner input status Total Bitrate: Total bitrate of Tuner input...
Page 16
DMM-Series User Guide V1.2 3.1.3 Source: Select from Tuner, ASI Input, IP or MUX TS. Program column: Show the program name. Select column: Select the channels which you want to descramble. Free means this channel can be received without CAM; Bypass means to skip this channel, this program will be still scrambled;...
DMM-Series User Guide V1.2 3.1.4.3 Decoder Play Source: Select from Tuner, ASI Input, IP, MUX TS, CI Descramble or BISS De-encrypted. Program: Choose the program need to be played Mode Decoder Mode: Select from Manual Selection and First Service. First Service means to select the program no automatically, normally the first program in the TS.
DMM-Series User Guide V1.2 3.1.5 Output ASI1 Output Source: Select from Tuner, ASI Input, IP, MUX TS, CI Descramble or BISS De-encrypted. ASI2 Output Source: Select from Tuner, ASI Input, IP, MUX TS, CI Descramble or BISS De-encrypted. 3.1.6 BISS BISS Mode: Select from OFF, Biss E or Biss 1.
DMM-Series User Guide V1.2 3.1.7 Output Bit rate: Set output bit rate. TS input: Program list from ASI input. User can click ‘Refresh’ button to refresh the list. TS output: Select output program. 3.1.8 IP Out...
Page 22
DMM-Series User Guide V1.2 Source: TS/IP output signal source, select from: Tuner, ASI, CI Descramble. TS Pkts Per UDP: Set how many TS packages will be encapsulated in one UDP package. The valid range goes from 1 to 7. Protocol: Select from UDP or RTP.
Page 23
DMM-Series User Guide V1.2 IPTV Mode TS which come from the ‘source’ selected in previous step will be de-muxed to several single programs, and each program is packed into one IP stream. Channel Number: Select IPTV output channel number ranging from 1~6 (or 1~32).
DMM-Series User Guide V1.2 3.1.9 IP In Multicast IP: Multicast IP address. Multicast UDP port: Set Multicast UDP port number. Stream IP address: IP address of TS/IP signal source. Protocol: Network Protocol including UDP or RTP. Stream Netmask: Subnet mask of TS/IP signal source.
DMM-Series User Guide V1.2 3.1.10 Backup Main channel: select main channel from ASI or tuner. Backup channel: select backup channel from ASI or tuner. Main CH Unlock Time: set Main CH Unlock Time, ranging from 0 to 59 seconds. When signal of the main channel remains the disconnected status over this value, the unit will switch to the backup channel automatically.
DMM-Series User Guide V1.2 3.1.11 System 3.1.11.1 Device Device Information Unit Name: User can edit the unit name. Serial Number: The serial number of the unit. Optional Function External Board Type: Select from No Exist/IP out/IP in/QAM out. Mux Function:...
DMM-Series User Guide V1.2 3.1.11.3 Network Network Target device Device IP: IP address of current device. Net mask: Network mask Gateway: Gateway address MAC Address Alarm Setting Trap IP Addr: IP address of SNMP target device. NTP Server IP: Edit NTP Server IP.
DMM-Series User Guide V1.2 DMM-140 Decoder Module 3.2.1 Status Menu Output Status Video: Video status Audio: Audio status Input Status ASI: ASI input status Total Bitrate: Total bitrate of ASI input Packet size: ASI input Packet size Valid Bitrate: Valid bitrate of ASI input...
DMM-Series User Guide V1.2 3.2.2 Input Menu LNB Freq. (MHz): LNB local oscillator frequency SatFreq. (MHz): Satellite down link frequency Symbol rate (KBaud): Set Symbol rate LNB Voltage: Select from OFF/13V/18V LNB 22KHz: Select from OFF/22K DisEqc: Select from DisEqc Off, Port A, Port B, Port C, Port D 3.2.3...
DMM-Series User Guide V1.2 3.2.3.2 ASI2/SDI ASI2/SDI Output Mode: Select from ASI2/SDI Audio DID: Select from Group1~4 Emb Audios: Select from None/One/Two/One&Two 3.2.3.3 Decoder Play Source: Select from Tuner, ASI, CI Descramble, IP Program: Choose the program need to be played...
DMM-Series User Guide V1.2 3.2.3.4 Decoder Config Biss Mode: Select from OFF, Biss E or Biss 1. Biss 1 Setup: Password is required for Biss 1 setup. Biss E Setup: ID and Password are required for Biss E setup. Video Output Video Standard: Select from Auto, PAL, NTSC and SECAM.
Page 32
DMM-Series User Guide V1.2 3.2.4 Source: Select from Tuner or ASI. Program column: Show the program name. Select column: Select the channels which you want to descramble. Free means this channel can be received without CAM; Bypass means to skip this channel, this program will be still scrambled;...
DMM-Series User Guide V1.2 3.2.5 IP Out Source: TS/IP output signal source, select from: Tuner, ASI, CI Descramble. TS Pkts Per UDP: Set how many TS packages will be encapsulated in one UDP package. The valid range goes from 1 to 7.
Page 34
DMM-Series User Guide V1.2 DVB Mode TS which come from the ‘source’ selected in previous step will be directly packed into IP Stream. It requires configuration of the following parameters. Multicast/unicast IP: Multicast or unicast IP address setting. Target UDP port: Multicast UDP port number.
Page 35
DMM-Series User Guide V1.2 IPTV Mode TS which comes from the ‘source’ selected in previous step will be de-muxed to several single programs, and each program is packed into one IP stream. Channel Number: Select IPTV output channel number ranging from 1~6 (or 1~32).
DMM-Series User Guide V1.2 3.2.6 IP In Multicast IP: Multicast IP address. Multicast UDP port: Set Multicast UDP port number. Stream IP: IP address of TS/IP signal source. Protocol: Network protocol including UDP or RTP. Stream Netmask: Subnet mask of TS/IP signal source.
Page 38
DMM-Series User Guide V1.2 Device Info Unit Name: User can edit the unit name. Serial Number: The serial number of the unit. Version Main Version WEB Version Linux OS Version ARM S/W Version Decoder Version FPGA Version TS/IP Out NIOS...
DMM-Series User Guide V1.2 Technical Specification DMM-140 Series Tuner Input DVB-S/S2 Tuner Input Connector Type 1 x F type female 75Ω for Input, 1 x F type female 75Ω for loop through output Input Frequency Range 950 ~ 2150MHz Input Level...
Page 40
DMM-Series User Guide V1.2 TS Processing TS Input Management Remux and demux between Tuner, ASI and TS/IP Inputs TS Output Management Remux and demux for 2 mirror ASI outputs Service and PID management Remux, filtering and remapping PSI/SI PSI/SI table regeneration, NIT and SDT edition, LCN Edition...
DMM-Series User Guide V1.2 DMM-150 Series Tuner Input DVB-S/S2 Tuner Input Connector Type 1 x F type female 75Ω for Input, 1 x F type female 75Ω for loop through output Input Frequency Range 950 ~ 2150MHz Input Level -25 ~ -65dBm...
Page 42
DMM-Series User Guide V1.2 TS Processing TS Input Management Remux and demux between Tuner, ASI and TS/IP Inputs TS Output Management Remux and demux for 2 independent ASI outputs Service and PID management Remux, filtering and remapping PSI/SI PSI/SI table regeneration, NIT and SDT edition, LCN Edition...
DMM-Series User Guide V1.2 Baseband Data Output Subtitle DVB/EBU Teletext, WSS, VFD, VPS Closed Caption EIA 608, EIA 708, EIA 608-to-708 Redundancy Redundancy Port between Tuner, 2 x ASI inputs and TS/IP Switching Condition TS Sync Loss Switching Mode Main, Spare Control &...
Electromagnetic compatibility Limits – Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current <= 16 A per phase and not subject to conditional connection. This regards to the following Teracue products: DMM-100-FR DMM-140-S2 DMM-140-C...
<= 16 A per phase and not subject to conditional connection. This regards to the following Teracue products: DMM-100-FR, DMM-100-FR-1RU DMM-150-S2, DMM-150-C, DMM-150-T, DMM-150-T2 Designed, developed and manufactured to conform with the:...
Page 46
<= 16 A per phase and not subject to conditional connection. This regards to the following Teracue products: DMM-100-FR, DMM-100-FR-1RU DMM-220-S2, DMM-220-T/T2/C Designed, developed and manufactured to conform with the:...