Download
Share
Print this page
  1. Manuals
  2. Brands
  3. STL Manuals
  4. Elliptical Trainer
  5. FitSpine System
  6. Assembly instructions manual

STL FitSpine System Assembly Instructions Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
S
t p
ne
S Y S T E M
T M

Assembly Instructions

For more information about your FitSpine
System, refer to the:
1. Owner's Manual
2. Contact Customer Service at 1-800-847-0143
3. Visit www.FitSpine-System.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the FitSpine System and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for STL FitSpine System

  • Page 1: Assembly Instructions

    S Y S T E M Assembly Instructions For more information about your FitSpine System, refer to the: 1. Owner’s Manual 2. Contact Customer Service at 1-800-847-0143 3. Visit www.FitSpine-System.com...

  • Page 2: Pre-Assembly

    PRE-ASSEMBLY Before you begin: Review all steps before beginning assembly and read all precautions before using the inversion table. Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure user safety and product integrity. IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE. WARNING WARNING - To reduce the risk of injury to persons:...

  • Page 3: Items For Assembly

    PRE-ASSEMBLY ITEMS FOR ASSEMBLY Carefully remove the individual parts from the carton. You should have all of the items listed below. If you have any questions on assembly, contact Customer Service at 1-800-847-0143. Items for Assembly Item Numbers A-frame Base (FS-1010) Stability Feet (IA-1101)
  • Page 4 ASSEMBLY Before Beginning Before reading further, study the drawing below to familiarize yourself with the important components of your new inversion table. Table Bed Traction Bars Lumbar Pillow A-frame Crossbar Support Handles Ankle Lock System Support Handle Shroud Adjustable Foot Platform Nylon Tether Main Shaft Ankle...
  • Page 5 ASSEMBLY Step One Assemble the Stability Feet (IA-1101) and the A-frame Base (FS-1010)  Set the A-Frame so the base points up (Figure 1). This will Figure 1A give you downward leverage to properly assemble the Stability Feet. Steady both sides of the A-frame so the legs do not swing open.
  • Page 6 ASSEMBLY Step Two Lock the Roller Hinges (F5-1064) onto the Table Bed Assembly (FS-1030) • For ease of assembly, rest the Table Bed against the side of the A-frame (Figure 3). • Open the cam locks on each side of the Table Bed. Figure 3 •...
  • Page 7 ASSEMBLY Step Three Attach the Table Bed Assembly (FS-1030) to the A-frame pivot pin (FS-1010) • Holding each side near the Roller Hinges, pick up the Table Bed and stand at the front of the A-frame where the crossbar is located. Lower each pivot pin into the A-frame hinge plates at the same time (Figure 6).
  • Page 8 ASSEMBLY Step Four Insert the Main Shaft (FS-1050) into the Table Bed Assembly (FS-1030) • With the height adjustment settings on the Main Shaft facing up, slide the end of the Main Shaft into the bushing in the Main Shaft housing (Figure 9).
  • Page 9 ASSEMBLY Step Five Install the Front Ankle Assembly • Gather the Ankle Bar (FS-1060), Black Plugs (F5-1056), Foam Rollers (F5-1051), Bolt Sleeve (IA-1110), and Sleeve Screw Ratchet Housing (IA-1112). • Stand in front of the Main Shaft and slide the Ankle Bar over the Figure 12 ratchet housing into the slot (Figure 12).
  • Page 10 ASSEMBLY Step Six Figure 15 Install the Rear Bar Assembly • With the rounded corners of the rear foam Heel Cup facing down, insert the Rear Bar with one Heel Cup (IA-1113) into the large hole at the bottom of the Main Shaft (Figure 15).
  • Page 11 ASSEMBLY Step Seven Install the Foot Platform Assembly • Slide the Foot Bar (IA-1119) with one pre-assembled Foot Piece (IA-1118) in the hole below the ratchet (Figure 18). Figure 18 • Slide the other Foot Piece onto the Bar (Figure 18). •...
  • Page 12 ASSEMBLY Step Nine Attach the Support Handle Shrouds (FS-1025) Support Handle Shroud • Select the corresponding Shroud for the left or right side on the A-Frame Base by aligning each with the shape of the hinge plate. Secure with two hex bolts (H1-1202) for each side using the wrenches provided.
  • Page 13 POST-ASSEMBLY ADJUSTMENTS / MAINTENANCE / STORAGE CHANGING THE ROLLER HINGE SETTING • Stand with your legs on either side of the Main Shaft. • Reach under each Roller Hinge with your index fi ngers. Use your thumbs to release the locks over the Roller Hinges (See Figure 23).
  • Page 14 Any modifi cation to this device will void the UL Listing. WARNING Read the Owner’s Manual thoroughly before using your FitSpine System. Improper settings could result in serious injury or death! If you have any problems assembling the equipment, or questions about its use, please contact customer service at: U.S.