Table of Contents
Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
(Internal Dimensions)
Ent Spec Edition Ltr v2-0-4
Overall dimensions including base:
247.4 L x 193 W x 210 H cms
97.5" L x 76" W x 82.7" H
IMPORTANT!!!
Please
read these instructions carefully before you start to assemble this greenhouse. To save time and
ensure proper assembly, follow the step-by-step instructions carefully in order. Assembly is easiest when
at least two people are present. Keep these instructions in a safe place for future reference.
An updated and/or improved version of this assembly guide may be available for download from the
HobbyGrower web site. Also, if you would like to view a brief general assembly video to gain a basic
understanding of how the structure is constructed, visit
http://www.hobbygrower.com, then click on the Assembly tab.
Advertisement
Table of Contents
Related Manuals for HobbyGrower Enthusiast6"x8"
Summary of Contents for HobbyGrower Enthusiast6"x8"
- Page 1 An updated and/or improved version of this assembly guide may be available for download from the HobbyGrower web site. Also, if you would like to view a brief general assembly video to gain a basic understanding of how the structure is constructed, visit...
-
Page 2: Safety Advice
SAFETY ADVICE • Do not attempt to assemble the greenhouse in • Do not lean on or push against the greenhouse windy or wet conditions. during construction. • Take special care not to touch overhead power • Keep children away from assembly area - the cables with aluminum profiles. - Page 3 CONTENTS Note: 1 inch = 25.4 millimeters (mm) Important! Be sure to inventory and organize parts prior to beginning the assembly process. ITEM QTY. ITEM QTY. ITEM QTY. 600 x 600mm 1190mm (46.8") (23.6" x 23.6") 12mm (0.47") 600 x700 mm 1290mm (50.7") (23.6"...
- Page 4 Height: 200 cm (78.8") Length: Width: 247.4 cm (97.5") 193 cm (76") Height: 10 cm (3.9") Length: Width: 245.5 cm (96.7") 190 cm (75")
- Page 5 Door Assembly Slide the rectangular panel 2 (must be Select profile 17-1290mm. the panel with the door handle hole) onto the profile ensuring it has the interlocking IMPORTANT: You must ensure that the profile is slot at its bottom.* oriented right-side up and with the plastic hinge plates facing out (Fig A).
- Page 6 Lay the assembly on the floor and insert an angled bracket 9 only into the bottom of profile 17-1290mm (A). Slide a 11-590mm profile onto the top and bottom of the door assembly (B), ensuring the angled bracket 9 11/590 slots into the bottom profile (see close up diagram).
-
Page 7: Wall Assembly
Wall Assembly Slide on a rectangular panel 3 and Stand the door up. On the door jam side, interlock the two panels as shown in slide on a square panel 1. It will be steps 3 and 4. easier if you open the hinge. Door Slide on another two panels and then a profile Slide on a corner profile 13-1290mm but... - Page 8 Slide on another vertical profile 14-1330mm Slide on a vertical profile 14-1330 and fit and carry on around the greenhouse until another set of two panels (note placement of you reach the door again. vent panel). Fit horizontal profile 14-590 as shown and slide on a top panel 4.
- Page 9 Note: You will require the assistance of another person to carry out the next stage of the assembly. You will be lifting the greenhouse and sliding six bottom rail profiles 11 onto the bottom panels. There are three different panel length profiles to use so study the diagram below closely.
- Page 10 Back Wall At the back wall of the greenhouse insert two metal connecting bars 10B/75mm into the top section of profiles 14-1330 as shown. 10B/75 Slide down profiles 10B/75 14-530mm both sides of panel 4 ensuring the angled end of the profiles are at the top and that they follow the same angle 10B/75...
-
Page 11: Roof Assembly
Roof Assembly Slide four panels 1 on to profiles 12 as shown. Slide two profiles12-1190mm along the top Repeat for other side. long sides of the greenhouse. Insert a joining bar 10 between each pair to strengthen the join. Panels may need aligning as you go. - Page 12 14mm Pre-drill holes using a 5/64" drill bit. Alternatively, you can simply poke a small starter hole in the plastic using a nail or sharp object that is similar in diameter to the 14mm screw. Note orientation of nipples 8mm and washer 8mm and washer...
- Page 13 Remove the protective poly film from these panels before installing. Dispose of poly film carefully to keep out of reach of children. Decide where you wish to place the roof vent panel 6. Slide it in position together with three panels 1. Repeat the process on the other side of the roof using three panels 1 and...
- Page 14 DOOR The Door Jam portion of 17-1290 has a cavity that is designed to accept both part number 32 Door Support and one side of part number 31 Bottom Door Jam Alignment Bracket (shown in step 26A). Identify the angled slot in the right door jam (figure A1). Insert part number 32 into the angled slot of the right door jam (figure A2).
- Page 15 Insert part number 33 Top Door Jam Alignment Bracket into the vertical slots of the left and right door jams. Note: part number 33 does not get inserted into the door frames. From outside the greenhouse, insert roof profiles 13/575 as shown.
- Page 16 DOOR DOOR OUTSIDE INSIDE INSIDE OUTSIDE From the inside of the greenhouse, apply Use pairs of roof brackets 21 to clamp 100% silicone caulk/sealant (compatible each roof section where shown (A). Fix with polycarbonate) to all roof joint holes. brackets in place using part number 22, Inject the silicone until it oozes through 12mm nuts and bolts (B).
- Page 17 Attach corner caps 23 in all ten positions (front and back) using screws 8. You will need someone to help you with this step (one person inside, another outside). Do not overtighten. Outside Inside IMPORTANT! This step should only be carried out if you are anchoring your greenhouse to a concrete surface, otherwise poceed to step 37.
- Page 18 Base Construction Joing the base sections together as shown. IMPORTANT! Ensure all the screw holes are facing toward the inside of the greenhouse and closer to the top edge of the sections. shorter Inside sections 25 are used on the long sides and the longer sections 26 are used on the shorter sides.
-
Page 19: Limited 5 Year Warranty
LIMITED 5 YEAR WARRANTY SPS International’s renowned reputation for its fine products results from their dedication and commitment to quality, design and innovation. The entire range of HobbyGrower brand horticultural products is manufactured from high quality ® materials under rigorous control and supervision. In case a problem should occur, please address your claim to the customer service department by phone.
Need help?
Do you have a question about the Enthusiast6"x8" and is the answer not in the manual?
Questions and answers