Auto darkening welding google with clipshield (5 pages)
Summary of Contents for Servore SERVO GLAS 5000X Autolift
Page 1
User’s Manual Auto-Darkening Welding Helmet SERVO GLAS® 5000X Autolift Made in Korea by SERVORE CO. #410-3 Tojin-ri Cheongbuk-myeon Pyeongtaek-si Gyeonggi-do Korea. TEL : +82-31-684-6952 ◆ FAX : +82-31-684-6954 Home page: www.servore.com E-mail: servore@servore.com...
Page 2
Note Safety is a personal responsibility. Servore endeavours to produce high quality safety products that meet or exceed relevant Standards and provide appropriate protection when used properly. Please help yourself and those around you by using this product carefully and by exercising good judgement.
Page 3
Please note that if you have any questions or there is any doubt about the performance of your Servore product you should refer to your authorized safety representative or Servo Glas® distributor.
Page 4
Always use genuine ServoGlas® front and inside cover plates. Failure to do so may result in injury and will void the warranty. The ServoGlas® 5000X is not designed for overhead welding without the use of additional protection. Check your helmet for physical damage and test it regularly.
Page 5
• Genuine Servo Glas® front and inside cover plates must always be used with Servo Glas® 5000X welding filter and helmet. Failure to do so may result in injury and also void any warranty. • Servo Glas® 5000X is not designed for use in overhead welding applications where additional protection may be required.
Page 6
EN379 and EN175 and other relevant Standards where indicated. The following example illustrates these requirements. Please note this example is provided for illustration purposes only. CE 4 / 9 -13 SERVORE 2 / 1 / 2 / 379 Light shade Dark shade...
Page 7
5 mm. This minimum dimension may be waived for small-scale PPE. <3 page> 3. Parts List The following parts are available from Servore and your authorized Servo Glas® distributor. Description Description Helmet Shell...
Page 8
Helmet Knob Parts Part No. Description Replacement of Knob Holder Band Holder Helmet Knob Set HK-1 P-bolt HK-2 Band Holder HK-3L Angular Stopper L HK-3R Angular Stopper R Move P-bolt back and forth to HK-4 Angular Washer adjust helmet distance HK-5 Washer between eyes and filter window.
Page 10
<6 page> 5. Control Function PARTS 1.Solar Cell Panel 2. Sensor 3.LCD Filter Plate 4. Shade Control 5. Delay Control 6. Sensitivity Control 7. RF Sensor Switch 8.Low Battery Indicator...
Page 11
<7 page> 5-1. Shade Control required filter dark state selected by using the shade control. The Servo Glas® 5000X can be adjusted between shades 9 to 13 with the embossed arrow on the dial indicating the current adjustment. Always use the appropriate shade for the welding operation you are undertaking.
Page 12
<8 page> 5-2. Light Sensitivity Control Where problems encountered during welding at low amps (e.g. TIG) or there is a high level of ambient light please follow these steps. First try adjusting the sensitivity control switch. Start with the sensitivity LOW (gently turn anticlockwise until the knob stops) and adjust upwards as required.
Page 13
5-4. RF Sensor Switch New RF High/Low switch for even better RF sensitivity control. Switch to high for extremely low amp TIG(down to 1 amp) or when using shielded cables and welders. Switch to low when working near other welders or in areas of high RF interference to avoid false triggers and for general welding.
Page 14
Again, you must remove the protective film from both sides of the cover lens before installing it. Always use genuine Servore parts. Never use a welding helmet without both front and rear cover lenses installed.
Page 15
at least every three years. Always replace both batteries at the same time with brand new batteries. Never install previously used batteries in your helmet. To replace the batteries slide out the battery holders from either side of the cartridge and discard the old batteries. Install the new batteries in the battery holders and slide the battery holders back into the cartridge.
Page 16
6-4. Maintaining the Auto Lift assembly on the 5000X Auto Lift Assembling and disassembling the Auto Lift assembly on the 5000X Auto lift is a simple process but should be done according to the following instructions to ensure problem free operation of the helmet. Locate the spring (10-3L) in the recess on the outside of the helmet shell ensuring that the end of the spring is hooked into the hole provided and pointing upwards.
Page 17
the inside of the shell. Note that the black washer has internal fins that mate with the end of the slotted bolt. Insert the self tapping screw into the washer and screw it in. Avoid over- tightening. Use a coin to tension the springs on each side by turning the head of the slotted bolts with a coin.
Page 18
<12 page> 7. Storage and Temperature Range Your Servore welding helmet is strong and durable. It is designed to work in temperatures between -5C and +55C. Do not use your helmet in very hot conditions where temperatures exceed +65C. Always store your helmet in a clean dry place out of the direct sun and protect it from exposure to moisture or extreme heat (min/max storage temperature is -20C ~ +70C).
Page 19
based lubricant may be used on moving parts if necessary but is not normally required. The filter may be carefully wiped with a cloth dampened with household window cleaning solution. Please be careful not to scratch or otherwise damage the filter cartridge with fragments of welding spatter or other abrasive dirt.
Page 20
Before use perform all normal system checks and if in any doubt contact your ServoGlas® distributor. Your Servore helmet is a precision engineered professional protection product and must be maintained in good condition to ensure your personal protection.
Page 21
• Servore reserves the right to make improvements, change or otherwise modify the specifications, materials and design of CAUTION any and all Servore products at their sole discretion with a view to ensuring continuous improvement. Never attempt any unauthorized modifications or alterations to your Servore product.
Page 22
11. Transmittance Curve of the Welding Filter 12. European Representative for SERVORE CO. Company Name SERVORE INTERNATIONAL Contact Person Steve Edwards Address 21 Dawson street Dublin 2 Ireland Telephone +353 1 678 4271 +353 1 662 4437...
Page 23
Thank you for purchasing a Servore product. If you have any questions regarding this or any other Servore product please contact your authorized ServoGlas® distributor. This model is certified by: CERTOTTICA S CERTOTTICA Scarl carl..CERTOTTICA S...
Need help?
Do you have a question about the SERVO GLAS 5000X Autolift and is the answer not in the manual?
Questions and answers