RHINO R1T1 User Manual

Rhino open source telephony pci and pci express cards for linux

Advertisement

                                      
Rhino Equipment Corp. is proud to manufacture our products in the U.S.A.
Specifications are subject to change without notice.
 2006, 2007  Rhino Equipment Corp. All rights reserved. Printed in U S America 4/2007  PN 031­00006
Rhino® is a registered trade mark of Rhino Equipment Corp.
Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826
Rhino  Open Source 
Telephony PCI and
PCI Express Cards 
for Linux
Models:
T1/E1 Models:
•R1T1, R1T1­e: Single port T1 PCI card 
•R2T1, R2T1­e: Dual port T1 PCI card
•R4T1, R4T1­e: Quad port T1 PCI card
Fixed Analog Models:
•R4FXO­EC: Quad FXO Channels with Echo Cancellation
•R24FXS­EC: 24 port FXS Channels with Echo Cancellation
•R24FXO­EC: 24 port FXO Channels with Echo Cancellation
Modular Analog Models:
•R8FXX: Modular Octal FXS/FXO with Echo Cancellation
•R24FXX: Modular 24 FXS/FXO with Echo Cancellation
Daughter cards: 
•DFXS: Dual FXS Module
•DFXO: Dual FXO Module
1
User Manual 

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the R1T1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for RHINO R1T1

  • Page 1: Rhino  Open Source Telephony Pci And Pci Express Cards

    Rhino  Open Source  Telephony PCI and PCI Express Cards  for Linux                                        User Manual  Models: T1/E1 Models: •R1T1, R1T1­e: Single port T1 PCI card  •R2T1, R2T1­e: Dual port T1 PCI card •R4T1, R4T1­e: Quad port T1 PCI card Fixed Analog Models: •R4FXO­EC: Quad FXO Channels with Echo Cancellation •R24FXS­EC: 24 port FXS Channels with Echo Cancellation •R24FXO­EC: 24 port FXO Channels with Echo Cancellation Modular Analog Models: •R8FXX: Modular Octal FXS/FXO with Echo Cancellation •R24FXX: Modular 24 FXS/FXO with Echo Cancellation Daughter cards:  •DFXS: Dual FXS Module •DFXO: Dual FXO Module Rhino Equipment Corp. is proud to manufacture our products in the U.S.A. Specifications are subject to change without notice.  2006, 2007  Rhino Equipment Corp. All rights reserved. Printed in U S America 4/2007  PN 031­00006 Rhino® is a registered trade mark of Rhino Equipment Corp. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 2 Managing your open source telecommunication needs has never been easier than with Rhino  products.  Rhino PCI plug­in cards satisfy the needs of Open Source Telephony (OST)  applications, no matter how stringent the requirement. Rhino Open Source  T elephony PCI  cards feature Asterisk* and Linux tested software.  Knowing that Rhino products are ready  to perform right out of the box means that you can spend more time developing important  customer relationships. Rhino Equipment Corp. offers you a complete line of low cost PCI plug­in cards including  Single T1/E1, Dual T1/E1, Quad T1/E1, all three with optional echo cancellation using a  plug­in module, and our analog cards, the Quad FXO analog, Octal FXS/FXO modular, 24­ port FXS/FXO modular, and the R24FXS and R24FXO fixed circuit analog interfaces, all  with echo cancellation on­board. Also, don’t forget our full line of Rhino Channel  B ank  products, for large­scale analog FXS or FXO applications.   Thank you for purchasing a Rhino Open Source Telephony (OST) PCI card. For unparalleled  performance and years of operation please follow the instructions provided in this user  manual.   Rhino designed products are tough.  In the rare case of trouble, our technical support staff is  ready to give you the support you need, when you need it.  Our 5­year, limited warranty  means that you can be confident that Rhino will always work in your Open Source  Telephony application. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 3: Software License

    * Asterisk is a registered trademark of Digium. Software License All Rhino OST PCI cards require Linux module software to operate.  We distribute our software under the GNU General Public  http://www.gnu.org/copyleft/gpl.html License, which is enclosed here for your review.(as obtained from  GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc.   51 Franklin Street, Fifth Floor, Boston, MA  02110­1301, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public  License is intended to guarantee your freedom to share and change free software­­to make sure the software is free for all its users. This  General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to  using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply  it to your programs, too.  When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you  have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it  if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.  To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights.  These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.  For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you  have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their  rights.  We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to  copy, distribute and/or modify the software.  Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free  software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the  original, so that any problems introduced by others will not reflect on the original authors' reputations.  Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program  will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent  must be licensed for everyone's free use or not licensed at all.  The precise terms and conditions for copying, distribution and modification follow.  TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be  distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work  based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the  Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is  included without limitation in the term "modification".) Each licensee is addressed as "you".  Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 4 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and  distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:  a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.  b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or  any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.  c) If the modified program normally reads commands interactively when run, you must cause it, when started running for  such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice  and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the  program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is  interactive but does not normally print such an announcement, your work based on the Program is not required to print an  announcement.)  These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and  can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those  sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work  based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend  to the entire whole, and thus to each and every part regardless of who wrote it.  Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to  exercise the right to control the distribution of derivative or collective works based on the Program.  In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a  volume of a storage or distribution medium does not bring the other work under the scope of this License.  3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms  of Sections 1 and 2 above provided that you also do one of the following:  a) Accompany it with the complete corresponding machine­readable source code, which must be distributed under the terms  of Sections 1 and 2 above on a medium customarily used for software interchange; or,  b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost  of physically performing source distribution, a complete machine­readable copy of the corresponding source code, to be  distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,  c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative  is allowed only for noncommercial distribution and only if you received the program in object code or executable form with  such an offer, in accord with Subsection b above.)  The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete  source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to  control compilation and installation of the executable. However, as a special exception, the source code distributed need not include  anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the  operating system on which the executable runs, unless that component itself accompanies the executable.  If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access  to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to  copy the source along with the object code.  Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 5 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the  original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further  restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to  this License.  7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues),  conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do  not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this  License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent  license would not permit royalty­free redistribution of the Program by all those who receive copies directly or indirectly through you,  then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.  If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to  apply and the section as a whole is intended to apply in other circumstances.  It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such  claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by  public license practices. Many people have made generous contributions to the wide range of software distributed through that system in  reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software  through any other system and a licensee cannot impose that choice.  This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.  8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the  original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding  those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates  the limitation as if written in the body of this License.  9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new  versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.  Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and  "any later version", you have the option of following the terms and conditions either of that version or of any later version published by  the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever  published by the Free Software Foundation.  10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the  author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software  Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all  derivatives of our free software and of promoting the sharing and reuse of software generally.  NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE  EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT  HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER  EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY  AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE  Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 6 PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY  SERVICING, REPAIR OR CORRECTION.  12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT  HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED  ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR  CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT  LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD  PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR  OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 7: Products: R1T1, R1T1­E, R2T1, R3T1­E,  R4T1, R4T1­E, R4Fxo, R8Fxx, R24Fxx, R24Fxs, And R24Fxo Models

    User Information for FCC Part 68   Products:  R1T1, R1T1­e, R2T1, R3T1­e,  R4T1, R4T1­e, R4FXO, R8FXX, R24FXX,  R24FXS, and R24FXO models This equipment complies with Part 68 of the FCC rules and the requirements adopted by the  ACTA. On the bottom of this equipment is a label that contains, among other information, a  product identifier in the format US: AAAEQ##TXXXX (where “X’s” are shown will  represent product number, for example R1T1). If requested, this number must be provided to  the telephone company. This equipment uses the standard RJ11C, RJ21 or RJ­48C jack types for network connection. A plug and jack used to connect this equipment to the premises wiring and telephone  network must comply with the applicable FCC Part 68 rules and requirements adopted by  the ACTA. A compliant telephone cord and modular plug is provided with this product. It is  designed to be connected to a compatible modular jack that is also compliant. See  installation instructions for details. If this equipment causes harm to the telephone network, the telephone company will notify  you in advance that temporary discontinuance of service may be required. But if advance  notice isn’t practical, the telephone company will notify the customer as soon as possible.  Also, you will be advised of your right to file a complaint with the FCC if you believe it is  necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone  company will provide advance notice in order for you to make necessary modifications to  maintain uninterrupted service. If trouble is experienced with this equipment, for repair or warranty information, please  contact Rhino Equipment Corp, 8240 S. Kyrene Road, Suite 107, Tempe, AZ  85284.  Tel:  800.785.7073. If the equipment is causing harm to the telephone network, the telephone  company may request that you disconnect the equipment until the problem is resolved. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure  the installation of this equipment does not disable your alarm equipment. If you have  Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 8 User Information for FCC Part 15 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS  SUBJECT TO THE FOLLOWING TWO CONDITIONS:  1(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND  2(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE, RECEIVED,  INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.  NOTE: This equipment has been tested and found to comply with the limits for a Class B digital  device, pursuant to part 15 of the FCC Rules. These limits are designed to provide  reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed  and used in accordance  w ith the instructions, may cause harmful interference to radio  communications. However, there is no guarantee  t hat interference will not occur in a  particular installation. If this equipment does cause harmful interference to radio or  television reception, which can be determined by turning the equipment off and on,  the user is encouraged to try to correct the interference by one or more of the  following measures:  ­ Reorient or relocate the receiving antenna.  ­ Increase the separation between the equipment and receiver.  ­ Connect the equipment into an outlet on a circuit different from that to which the        receiver is connected.  ­ Consult the dealer or an experienced radio/TV technician for help.  NOTE: RHINO EQUIPMENT CORP. IS NOT RESPONSIBLE FOR ANY RADIO OR TV  INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS  EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S  AUTHORITY TO OPERATE THE EQUIPMENT   Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 9 This page intentionally left blank. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 10: Table Of Contents

    Table of Contents: Rhino  Open Source Telephony PCI and PCI Express Cards                                                                                                                                                ............................     1     for Linux                                                                                                                                                                 ................................     1     Software License                                                                                                                                                    .............................      3     Products: R1T1, R1T1­e, R2T1, R3T1­e,  R4T1, R4T1­e, R4FXO, R8FXX, R24FXX, R24FXS, and  R24FXO models                                                                                                                                                     ..............................  ...
  • Page 11: Preinstallation

    1.  PREINSTALLATION  Rhino OST PCI cards are easy to setup and use, which will make your telephony life easier!  Please spend a few minutes reviewing these instructions to ensure a successful installation. 1.a Warranty Rhino OST PCI cards are covered by a 5­year limited factory warranty. The warranty  statement is available on the Rhino web site, the Rhino CD­ROM, the Rhino Public FTP, or  by request. Please note that damage caused by improper installation or acts of nature are not  covered by this warranty. 1.b Standards   This equipment complies with Part 68 of the FCC Rules.  The number is located on the  back of the Rhino OST PCI Card. The label contains the FCC Registration Number for this  equipment.  If requested, this information must be presented to your telephone company. Connection to the telephone network should be made by using standard modular network  jacks, type RJ45.  The plug and/or jacks used must comply with FCC Part 68 Rules. OPERATION                               FIC                    SOC            (USOC) JACK       T1 CSU Interface 04DU9­BN 6.0N       RJ48C                         04DU9­DN 04DU9­1KN 04DU9­1SN If this telephone equipment causes harm to the telephone network, the telephone company ...
  • Page 12: Surge Protection

    If trouble is experienced with this unit, please contact customer service at the address and  phone listed below.  DO NOT DISASSEMBLE THIS EQUIPMENT .  It does not contain  any user serviceable components. Contact: Rhino Equipment Corp. Attn:   CUSTOMER SERVICE DEPT. 8240 S. Kyrene Rd. Suite 107 Tempe, AZ 85284 Ph 480­940­1826, Fax 480­961­1826 You must receive an RMA (Return Material Authorization) number from us so that your  return is handled promptly.  Failure to do so may result in a lost or delayed replacement. 1.c Surge Protection  It is recommended that a surge protector or uninterruptible power supply (UPS) be installed  in conjunction with the PC that the Rhino OST PCI card is installed in.  This will help  minimize damage as a result of lightning strikes and other AC line surges.  Failure to use a  UPS could affect the 5 year limited warranty. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 13: Installation

    2.  INSTALLATION   2.a Site Selection The selected installation site should provide a stable operating environment.  The area  around the installation site should be clean and free from extremes of temperature,  humidity, shock, and vibration.  The operating temperature should be kept below 100  degrees F (38  C). The Rhino OST PCI card is designed to be used on T1/DS1/ISDN­P RI/E1 services for a T1    card, or to be connected to the PSTN when using and analog card.  Connecting it to any  other type of telecommunications service or services will void the warranty and could  cause damage to the network of the provider of the non­approved service or services. All wiring done external to the Rhino OST PCI card should follow the guidelines as set   forth by the National Electrical Code. See section 1.b and 3.a. 2.b Unpacking the Rhino PCI Card The unit comes tested and sealed in an anti­static custom shipping box. The package  contains the Rhino OST PCI card Users Manual, and  a  Rhino Products CD containing the  most recent drivers and documentation. Before removing the card from its packaging, ensure that you are grounded.  To ground yourself please use an Anti­Static wrist band.  Inspect the Rhino OST PCI card for any signs of physical damage.  Report any damages  to the shipper.  Keep all packaging material in the event that you need to move or ship  the unit. Warranty returns must be shipped back to Rhino Equipment Corp in the  original shipping box. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 14: Physical Installation

    2.c Physical Installation Before removing the card from its packaging, ensure that you are grounded.  To ground yourself please use an Anti­Static wrist band. While removing the Rhino OST PCI card take care to only handle the mounting bracket,  avoid making contact with any of the PCI card circuitry. The Rhino OST PCI card is  intended to be installed in an ATX form factor motherboard, the chassis housing the Rhino  OST PCI card should also be an ATX form factor chassis.  Failure to install the Rhino OST  PCI card in this configuration will affect the warranty of your Rhino product(s). Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 15: Installation For T1 Ost Cards

    Fig 1. 3. INSTALLATION FOR T1 OST CARDS 3.a Connecting the Rhino T1 Card to T1/E1/PRI  The Rhino OST T1 cards (DS1) interface is an industry­standard RJ48C eight pin  connector with its connections described below.  The T1 is usually connected to a Rhino  CB24 channel bank or the telecommunications carrier demarcation point.  If the T1 is  coming from a Rhino CB24 channel bank, the T1 cable must be a crossover T1 cable.   Figure 2 shows the pin out for building a T1 crossover cable. This cable can be used to  connect two T1 CSU/DSU (i.e. TSU) products in a point­to­point configuration.  Fig 2. If the T1 is coming from the demarcation point please use a straight thru T1 cable to  connect to the Rhino OST T1 card.  In some cases additional cable must be run from the  carrier’s demarcation point to the customer’s suite or nearby “phone room”. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 16 Not connected Transmit Ring Going To T1 (Network) Transmit Tip Going To T1 (Network) Not connected 7            Not connected 8       Not connected The maximum cable length for a T1 Network (DS1­1) connection is suggested as follows.  Reliable T1 cabling distances depend on which type of cable is used.  It is strongly  recommended that only shielded cable be used as part of any T1 installation.  For best  results use:  shielded 22 AWG T1 cable (ABAM 600). ABAM 600 T1 Cable T1 Network (CSU)      can go as far as 6,000 feet ABAM 600 Cable Specifications: Nominal Impedance:  100 ohms +/­ 5% at 772 kHz. Insertion Loss: Better than 7 dB per 1,000 feet at 1.544 MHz. Better than 5 dB per 1,000 feet at 772 kHz. Far­End Crosstalk: Better than 85 dB per 1,000 feet at 1.544 MHz. Better than 90 dB per 1,000 feet at 772 kHz. Near­End Crosstalk: Better than 80 dB per 1,000 feet at 1.544 MHz. Better than 85 dB per 1,000 feet at 772 kHz. Shields: Transmit and receive pairs are individually shielded with  aluminum/polyester tape. If you used unshielded cable you could experience problems.  When this type of cable is  used, transmit and receive pairs are usually run in separate cables to avoid crosstalk which  often occurs in unshielded cables.  Failure to use separate cable bundles for transmit and  receive can result in the CSU LINE port clocking onto itself (due to crosstalk) with as little  as 10 feet of un­terminated (unshielded) telephone cable attached.  The CSU can thus show  a normal framed status when the far end of the telephone wiring is actually disconnected.  Again, this is due to crosstalk between pairs in the same cable bundle.  This is true of any  CSU installation using any kind of unshielded twisted pair cable. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 17: Hardware Configuration

    3.b Hardware Configuration Fig 3   Normally, no other configuration is necessary to get a Rhino digital telephony card to  operate in a system.  In cases where multiple cards are used within the same system, or  mixed E1 and T1 modes are needed on the same card, additional configuration may be  necessary. Timing Cable  A special 20 pin ribbon cable can be used to connect multiple Rhino digital telephony cards  to provide a common clocking source to all spans.  In Fig. 3, box 1 shows the location of  the Timing cable connector.  Obtain this cable direct from Rhino by contacting Technical  Support.  Please note that special command line options must be provided when loading the  module to allow for this option to operate as planned. T1/E1 Span Selector In cases where all cards of the same type are not configured the same; or when enabling E1  (T1 is the default configuration). The span selector pin header can be used to select the  desired mode for each span.  In Fig. 3, box 2, the span type selection can be made by  installing a shorting midgie across the span where E1 is desired.  There are two options for  this situation: Option 1: By using insmod, or putting the parameter in modprobe.conf (or a file in the    directory /etc/modules.d/ depending on the distribution). Bit 0 of xx is a 0 to configure span  1 as a T1 or a 1 to configure span 1 as E1. Bit 1 configures span2 etc. Example: t1e1 = 3  configures span 1 as E1, span 2 as E1, span 3 as T1, and span 4 as T1. All installed cards  will have the same configuration. The line looks like: Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 18: Installation Notes, Located In The Following Section

    Option 2: Override t1e1 = xx with module parameter at module load time. Values for xx  are the same as Option 1. All cards will have the same configuration. To make your Rhino T1 to a Rhino E1:  insmod rxt1.ko t1e1overide=15 Load Identifier (Module Instance Load order) Normally Linux loads PCI devices in the order that they are found on the PCI bus, most  likely from the PCI slot closest to the CPU on the motherboard, and outward from that  position.  For a digital telephony card, slot 1 would become the first span loaded, and  would default to Span 1 in all configurations.  The Load rotary switch allows for alternate  loading of the position of the PCI card, and allows for spans to be loaded in a different  order than how the cards are located in the motherboard. 3.c Generic Instructions for Installing ALL Rhino PCI cards. Note: The Rhino drivers (module)  are only compatible with the Linux kernel 2.6.9 and  higher. Please make sure  t his is installed and the Rhino OST PCI card is properly  installed before continuing with the software configuration. If you are using TrixBox 2.x  and above please see the Zaptel source installation notes, located in the following  section. 1. Boot the PC and log in as “root” or other user that has appropriate software build  privileges. 2. Navigate to the Zaptel source directory. This is normally located in:  “/usr/src/zaptel”.  If the Zaptel source is not present, you will need to download  that using the next sections.  If the Zaptel directory is already present, you may  jump to number 10 below. Note: The zaptel source directory can be anywhere on your hard drive, you will need to  locate where you installed zaptel if the above example does not work for you.  However if  the zaptel directory is anything other than “/usr/src/zaptel” then create a link that points  to the actual Zaptel source directory. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 19 Zaptel Source Installation Notes (only if needed, these optional steps are shown with a  >x below, items 3 through 9 below): Note: For Trixbox 2.x users the Zaptel source and kernel­headers must be downloaded.  If you are using Trixbox 2.x you need to download the Zaptel source, and recompile Zaptel.  In the “/usr/src” directory (cd /usr/src) please install zaptel: >3. Download the Zaptel source, making sure that you are in the /usr/src directory: wget ftp.digium.com/pub/telephony/zaptel/releases/zaptel­version.number.tar.gz >4. Decompress the downloaded tarball tar ­xzvf zaptel­version.number.tar.gz >5. Create a symbolic link to zaptel: ln ­s /usr/src/zaptel­version.number.tar.gz /usr/src/zaptel >6. Change your present working directory to /usr/src/zaptel cd /usr/src/zaptel >7. Now grab your specific kernel headers:                    Non­SMP: yum install kernel­devel  For SMP:   yum install kernel­smp­devel  >8. Correct the rw_lock_t spinlock error: sed ­i s/rw_lock/ /usr/src/kernels/`uname ­r`/include/linux/spinlock.h >9. Compile Zaptel make && make install 10.  In the “/usr/src/” directory please do the following ONLY IF your zaptel directory is different  than “/usr/src/zaptel”: ln ­s /usr/src/zaptel­xxx /usr/src/zaptel  (where”/usr/src/zaptel­xxx” is the path of your installed zaptel directory.) Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 20 11. Download the Rhino drivers  in a single package: wget ftp://ftp.rhinoequipment.com/Drivers/rhino­version­#.tbz2 12. Extract the .tbz2 file to its own directory tar ­xjvf rhino­version­#.tbz2 13. Next change the directory into the Rhino Driver Directory, and run “make” as follows: make && make install (This will make and install the Rhino drivers independently of Zaptel and Asterisk.  You may  optionally use make, then make install to perform this in two separate command line sessions) 14. Next type the following command in the prompt to update the driver database: depmod  15. Now load your module.  Depending on your card(s) type one of the following commands. For R4FXO rev A and B type: modprobe r4fxo For R4FXO rev C, R8FXX, R24FXX,  R24FXS, and R24FXO type: modprobe rcbfx For R1T1 type: modprobe r1t1 For R2T1, and R4T1 type: modprobe rxt1   16. Move on to configuring the zaptel interface. For more information on span and channel  configuration please refer to sections 3.d & 3.e. For configuration examples for Rhino analog  PCI cards please refer to section 4.c Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 21: Rhino Ost T1/E1 Pci Card Port And Span Configurations

    3.d Rhino OST T1/E1 PCI card Port and Span configurations The first lines of the zaptel configuration file (comments excluded) will be the span  definitions for T1/E1 interfaces.  A span definition is in this format: span=(spannum),(timing),(LBO),(framing),(coding) (see next page  for more examples) Spannum: Spannum defines the number assigned to the span these definitions apply to. If you  only have one R1T1 card installed you will only have one span (span 1), if there are  two single port R1T1 cards installed you will have two spans (span 1 corresponds to  the first port on the first module loaded). For an example of span numbering please  refer to figure 3.  Fig 4. (dimensions in inches) Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 22 Timing: Use '1' if you want to use the circuit as your primary timing source. If '0' is used  Asterisk will try to provide timing to the span (if you were connecting to a Rhino  CB24 this would be correct.).  If Asterisk is connected directly to the telco you will  want to use '1' to accept timing from them. If you have multiple spans; set the  timing accordingly such as 2, 3, 4, etc.  0: to not use this span as sync source  1: to use as primary sync source  2: to set as secondary and so forth  Tip: Problems with timing manifest themselves in different ways ­ with static, pops, and  channels or calls regularly dropping. LBO: Line Build Out (LBO) is taken from the table below. 0: 0 db (CSU) / 0­133 feet (DSX­1) 1: 133­266 feet (DSX­1) 2: 266­399 feet (DSX­1) 3: 399­533 feet (DSX­1) 4: 533­655 feet (DSX­1) 5: ­7.5db (CSU) 6: ­15db (CSU) 7: ­22.5db (CSU) Framing: For T1 ­ Framing is either d4 or esf. Coding is either ami or b8zs. For E1 – Framing is either cas or ccs. Coding is either ami or hdb3. E1’s spans may  also need to enable crc checking. T1 span configuration used to connect to a Rhino CB24: span=1,0,0,esf,b8zs A common E1 span configuration: span=1,0,0,cas,ami,crc4 Leave off the ‘,crc4’ if crc checking should not be enabled. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 23: Rhino Ost T1/E1 Pci Card Channel Configurations

    3.e Rhino OST T1/E1 PCI card Channel configurations Rule of Thumb: Have you ever heard someone say “Opposites attract”? The same  is true when configuring zaptel and Zapata for your Rhino OST PCI card. When  configuring the signaling for your interface channels remember that physical FXO  channels require FXS signaling and physical FXS channels require FXO signaling. When you are configuring your Rhino OST PCI T1 card to work with a Rhino CB24  please use the following signaling: (CB24­FXO) signaling = fxsks(zaptel.conf) fxs_ks(zapata.conf) (CB24­FXS) signaling = fxols(zaptel.conf) fxo_ls(zapata.conf) For CB24­MOD signaling see the example below zaptel.conf ;Span 1  span=1,0,0,esf,b8zs  ; First 4 channels are the FXO modular card fxsks=1­4  ; Next 16 channels are the 4 modular FXS cards fxols=5­20  zapata.conf  ;First 4 channels are the FXO modular card  signalling = fxs_ks  channe l => 1­4  ;Next 16 channels are the 4 modular FXS cards  signalling = fxo_ks  channel => 5­20  Once zaptel.conf and zapata.conf are configured, initialize the card with the new  configuration values by running “ztcfg” from the Linux command prompt.  Tip: After configuring the signaling for your Rhino OST PCI card, start   Asterisk in a terminal, then simply run “Auto T1” on your Rhino CB24 or   manually configure it with LOOP signaling ESF framing and B8ZS coding. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 24: Rhino  Ost T1/E1 Pci Card Led Status Codes

    3.f Rhino  OST T1/E1 PCI card LED Status Codes Below is a chart for LED state code for all Rhino OST PCI T1/E1 cards: GREEN STATE   Hardware       Self Power Check 2 Fast PCI Slot Recognition 4 Fast Registering PCI Card With BIOS 2 Fast 4 Fast Loading Firmware Module 2 Fast Synchronizing With System Bus Software       No Cable Link Detected Invalid Carrier Signal 2 Fade Module Loaded But Not configured Normal Operation 2 Fade 2 Fade Yellow Alarm, Down Stream Sending Error Signal 2 Fade 4 Fast Sending Loop Back Signal 4 Fast 2 Fade Receiving Loop Back Signal 4 Fast 4 Fast Recovering Note: You will see most blink codes on a normal boot up, however if the card halts at any state this could ...
  • Page 25: Installation For Rhino Ost Analog Cards

    4. INSTALLATION FOR Rhino OST Analog CARDS   4.a Connecting Rhino Analog cards to telco/extensions. The Rhino OST PCI analog cards use an industry standard RJ11 four pin plug for the  R4FXO quad port FXO card, with pin lay out shown below. And an industry standard RJ14  four pin plug for all octal modular cards (R8FXX), pin lay out is also shown below. Phone Line Interface on RJ11 ­ 4 pin Modular jack: Pin Number Signal To/From What? Not connected Line Ring RX Coming From PSTN (CO) Line Tip  TX Going to PSTN (CO) Not connected Phone Line Interface on RJ14 ­ 4 pin Modular jack: Pin Number Signal To/From What? Line 2 Tip TX Going to PSTN (CO) Line 1 Ring RX Coming From PSTN (CO) Line 1 Tip TX Going to PSTN (CO) Line 2 Ring RX Coming From PSTN (CO) Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 26 The 24 FXS channel (R24FXS) and modular 24 channel Rhino OST PCI (R24XX) analog  cards uses an industry standard RJ21 connection, shown below.    Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 27: Rhino Ost Pci Analog Card Channel Configurations

     4.c Rhino OST PCI Analog card Channel configurations Rule of Thumb: Have you ever heard someone say “Opposites attract”? The same  is true when configuring Zaptel and Zapata for your Rhino OST PCI card. When  configuring the signaling for your interface channels remember that physical FXO  channels require FXS signaling and physical FXS channels require FXO signaling. Rhino analog cards like LOOP and KEWL start signaling, so be sure to use just  these two signaling choices in your Zaptel and Zapata configuration files! When you are configuring your Rhino OST PCI analog card with only FXO channels use  the following signaling: zaptel.conf ; First 4 channels are the R4FXO card fxsks=1­4  ; Next 4 channels are the R8FXX card with two dual FXO modules installed fxsks=5­8  ;Next 4 channels are the R8FXX card with two dual FXS modules installed fxols=9­12 zapata.conf  echocancel=yes (this must be specified for enabling the hardware Echo Cancellation) ; First 4 channels are the R4FXO card signalling = fxs_ks  channel => 1­4  ; Next 4 channels are the R8FXX card with two dual FXO modules installed signalling = fxs_ks  channel => 5­8  ; Next 4 channels are the R8FXX card with two dual FXO modules installed signalling = fxo_ls  channel => 9­12 Important: Once zaptel.conf and zapata.conf are configured, initialize the card with the  new configuration values by running “ztcfg ­vvv” from the Linux command prompt.   This  will force zaptel to read your configuration files, and if there are errors, they will be  reported.  Errors must be fixed before continuing or zaptel will not identify the channels  correctly. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 28: Rhino Firmware File Update

    4.e Rhino Firmware File Update If a new firmware file update becomes available, be sure to install that firmware file into  the proper location.  For example, for Rhino analog cards, the rcbfx.fw file must be  installed into the /lib/firmware directory using: install ­m 644 rcbfx.fw /lib/firmware This assures that the firmware file will be updated the next time the Rhino module is  loaded, which normally happens when the PC boots.  You can manually force this event  using: rmmod rcbfx modprobe rcbfx or to force the uploading of the any version of firmware to the rcbfx analog card, which is  the last version that was “installed” using the install command: rmmod rcbfx insmod /lib/modules/`uname ­r`/extra/rcbfx.ko force_fw=1 You can use dmesg | grep rcbfx to view the status of the module loading, and to validate the hardware, firmware and DSP  version installed as well once the module has loaded. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 29: Connecting Power To The Rhino R8Fxx, R24Fxx, And R24Fxs Analog Card Installations

    4.f Connecting Power to the Rhino R8FXX, R24FXX, and R24FXS Analog  card installations Remember that the Rhino R8FXX card has only four physical connections on the back of  the card, and eight total analog line connections.  This is accomplished by using BOTH of  the wire connections on a RJ11 plug.  The center two pins are line 1, and the outside two  pins are line 2, on the top or first jack. Look on the back of the card to identify the  channels:  1­2 are on the top, and 7­8 are on the bottom. Note that both the R8FXX,  R24FXX, and the R24FXS cards require +12V power to give  the FXS channel its juice.  Be sure to connect a power supply ATX connector to the rear of  the card if that is the case.  Also note that it is not necessary to connect this power if there  are no FXS channels connected, as in a R8FXX with all FXO modules, a R24FXX with all  FXO modules, or the R24FXO card. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 30 There are two locations to look for FXS power indication.  A board level power indicator is  located at the connector end, and is a green LED.  Each FXS board also has a single LED  that can be seen off the reflection of the main board, at the top of the card. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 31: Rhino R4Fxo (Rev. C And Higher) And R8Fxx Led Codes

    4.g Rhino R4FXO (Rev. C and higher) and R8FXX LED Codes There are eight status LEDs located on the top right of the R8FXX board that depicts  channel status. GREEN STATE       Line not in use Line in use Rapid Flash Line ringing Slow Flash Line is in the process of being connected Ramp  On/Off FXO line does not see battery You can also use zttool to show the raw signaling data. There are also two master LED modes, when the computer boots and before the PCI side  configures, all of the eight LEDs should be on solid.  Once the PC boots and the card is  detected, a “night rider” display will engage.  Once the module is loaded (rcbfx),  t he LEDs  will then start to indicate status as per the above table. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 32 5.0 Rhino FTP Site Please note that Rhino Equipment Corp. maintains a FTP site where all of  t he latest  information is always available. ftp.rhinoequipment.com All rhino card drivers are provided within one installation package.  When navigating to the  Rhino FTP site, click on drivers and locate the updated package that you wish to install. It is simple to update your local copy of any Rhino driver by using wget, like this: wget ftp://ftp.rhinoequipment.com/Drivers/rhino­version.#.tbz2  If you are updating your drivers, it is safest to rename the current Rhino directory to a  backup directory.  Then pull the new drivers to a clean Rhino directory directory.  Use the  move (mv) command to do this. mv Current­Rhino­driver* Rhino­driver_backup This renames the current Rhino directory to a new directory called Rhino­driver_backup,  and all of the files contained in that directory.  Now you can pull the new files from the  Rhino ftp site and still have a copy of the old source driver files. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 33 6.0 Useful Linux­Asterisk Commands Be sure to login as root! Commands from the Linux command line Tab key – use this to “auto complete” command line entries, very useful! uname –r – displays the kernel version  cat /proc/zaptel/* ­ shows the installed zaptel compatible cards and channels modinfo rcbfx –    shows information about the associated linux driver modprobe rcbfx – load a module, in this case the rcbfx module, using the rules found in       /etc/modprobe.conf (i.e. used to load the module AND perform a ztcfg) insmod rcbfx.ko – load a module, all by itself.  This is particularly useful when a module has       command line options, use modinfo to see those rmmod  rcbfx – unload a module, in this case the rcbfx module lsmod – shows the installed linux modules, sometimes if the list is long using grep to isolate the   zaptel associated entries with lsmod | grep zaptel – display's only the zaptel and zaptel dependent modules lspci – shows the PCI cards installed cat /proc/interrupts ­ shows how the interrupts in a linux system are routed ztcfg –vvv – forces zaptel to read zaptel.conf, and to associate entries there with the module          interface with a verbose display zttool – show the zaptel compatible cards, their overall status, and if selecting a card, its individual  status and signaling states amportal – a freePBX specific command to start, stop, and restart asterisk and freePBX         dependencies. (i.e. amportal start, or amprotal restart) udevstart – restarts the module handling utility, normally this starts on boot Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 34 Commands to use from the Asterisk CLI zap show channels – shows the installed zap channels, this should mirror the zapata.conf channel           configuration extensions reload – used to load changes made to any dial plan file without having to restart        Asterisk service zaptel restart – reloads the zaptel modules and dependencies. Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 35 Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...
  • Page 36 If you have any other questions regarding the configuration or operation of your  Rhino  Equipment please contact our support staff: ® Email    support@rhinoequipment.com Phone (480) 940­1826 or (800) 785­7073 Thank you for choosing Rhino Equipment.                                Version 1.50    4/2007 Rhino Equipment Corp. • 8240 S. Kyrene Rd. • Suite 107 • Tempe, AZ 85284 • (480) 940­1826...

Table of Contents