Table of Contents
Advertisement
Quick Links
Electronic Service
Manuals
This electronic document is provided as a service to our customers.
We do not create the contents of the information contained in this docu-
ment. Should you have detailed questions pertaining to the information
contained in this document, you may contact Michco, or the manufac-
turer which provided the original information in this electronic deliver-
able. Michco's only part in this electronic deliverable was the electronic
assembly process. By providing this manual on line we are not guaran-
teeing parts availability.
You may contact Michco through the following methods:
Phone (517) 484-9312 or (800) 331-3339
2011 N. High St. -- Lansing, Michigan -- 48906
Fax: (517) 484-9836
Email: CustServe@Michco.com
Web site: www.Michco.Com
Parts Web site: www.FloorMachineParts.Com
Order Parts on Line at:
www.FloorMachineParts.Com
Directly to Parts & Service:
By Email:
Shop@Michco.com
By Fax: (517) 702-2041
By Voice: Use numbers above.
Serving the Cleaning Industry Since 1922
Notice: All copyrighted material remains property of original owners, all trademarks are property of respective owners.
Manuals are subject to Manufacturer's reproduction limitations. Originals or reproductions were provided by manufacturers
through a request. We make no warranty as to the correctness of information provided in this document and you assume
all risk. By placing these manuals on line we are not declaring our corporation to be an manufacturer authorized dealer or
provider, please check our web site for authorized manufacturers we represent.
Advertisement
Table of Contents
Summary of Contents for Sunbelt EZ-8
- Page 1 Electronic Service Manuals This electronic document is provided as a service to our customers. We do not create the contents of the information contained in this docu- ment. Should you have detailed questions pertaining to the information contained in this document, you may contact Michco, or the manufac- turer which provided the original information in this electronic deliver- able.
- Page 2 EZ-8 EZ-8 EZ-8 EZ-8 EZ-8 Operator's Sander Manual READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel;...
-
Page 3: Table Of Contents
Section II Parts and Service Manual Assembly Drawing #1 ..............14 Assembly Parts List #1 .............. 15 Assembly Drawing #2 ..............16 Assembly Parts List #2 .............. 17 Wiring Diagram ................18 Page 2 Sunbelt EZ - 8 Sander Operator's Manual... -
Page 4: Operator Safety Instructions
Do not operate unless drum cover, belt guard, and dust pipe are in place. Never leave machine unattended while motor is running or connected to power source. Sunbelt EZ - 8 Sander Operator's Manual Page 3... - Page 5 To avoid damage to the floor, feather cut in at a normal sanding rate. Do not dwell while lowering or raising the sanding drum. Always sand at a constant rate. Page 4 Sunbelt EZ - 8 Sander Operator's Manual...
-
Page 6: Introduction And Machine Specifications
Your equipment may be inappropriate on some installations. Always consult with the flooring manufacturer on the proper installation, preparation, and finishing of their product. Determine suitability of your equipment in preparing the product. Sunbelt EZ - 8 Sander Operator's Manual Page 5... -
Page 7: How To Transport The Machine
Figure # 2 7. Secure chassis to prevent movement in cargo area. Place handle and dust pipe in cargo area. Figure # 3 Figure # 4 Page 6 Sunbelt EZ - 8 Sander Operator's Manual... -
Page 8: Machine Set-Up
5. Connect the handle pigtail to the motor cord. Align ground pin, insert and twist. To install abrasive on sanding drum, slide abrasive over drum, center abrasive, and close drum cover. Figure # 6 Figure # 7 Sunbelt EZ - 8 Sander Operator's Manual Page 7... -
Page 9: How To Operate The Machine
Sanding dust can spontaneously ignite and cause a fire or explosion. Empty dust into a metal container clear of any combustible mate- rial. Page 8 Sunbelt EZ - 8 Sander Operator's Manual... -
Page 10: Sanding Cuts And Sandpaper
For final sanding of certain hardwoods. For 945936/10 945421/10 clean-up of initial cuts (50 grit). 100 grit For final sanding of certain hardwoods and 945937/10 945422/10 conifers where a smooth surface is desired. Sunbelt EZ - 8 Sander Operator's Manual Page 9... -
Page 11: Sander Adjustment Procedures
Figure # 10 to sand heavier on drive belt side of sanding drum. 3. Loosen the leveling screw (relax the leveling spring) to sand heavier on the side opposite the drive belts. Page 10 Sunbelt EZ - 8 Sander Operator's Manual... -
Page 12: Routine Maintenance
Relubricate every 150 hrs. w/.10 oz. of a NLGI grade 2, -30 F to 250 58-75 SUS at 210 grease lubricant. Motor shaft after 1 5000 hrs. Fan shaft After first 1500 hrs. Sunbelt EZ - 8 Sander Operator's Manual Page 11... -
Page 13: Troubleshooting
Burning or glazing. Dull abrasive. Replace abrasive. Too fine of an abrasive. Use a coarser abrasive. Waves on sanded surface. Debris on wheels. Remove and clean wheels. Flat spot on tire(s). Replace tires. Page 12 Sunbelt EZ - 8 Sander Operator's Manual... -
Page 14: Section Ii Parts And Service Manual
EZ-8 EZ-8 EZ-8 EZ-8 EZ-8 Sander Section II Parts and Service Manual (70214A) Sunbelt EZ - 8 Sander Operator's Manual Page 13... -
Page 15: Assembly Drawing #1 10/01
EZ-8 Sander Assembly Drawing #1 10/01 11 12 Page 14 Sunbelt EZ - 8 Sander Operator's Manual... -
Page 16: Assembly Parts List #1
Label, Lifting Warning 40545A 52465A Cover, Fan 51095A Capacitor Cover Motor Parts Not Illustrated Motor 44642A Part No. Description 41306A Capacitor Run 41307A Capacitor Start 47409A Starter Switch 47391A Thermal Switch Sunbelt EZ - 8 Sander Operator's Manual Page 15... -
Page 17: Assembly Drawing #2 10/01
EZ-8 Sander Assembly Drawing #2 10/01 34 35 45 47 Page 16 Sunbelt EZ - 8 Sander Operator's Manual... -
Page 18: Assembly Parts List #2 10/01
63928A Guard, Switch 980603 Washer, #10 Lock Ext. Th. 34610A Grip, Handle 70175A Tag, Warning Accessories Available: 70401A- Package of two disposable paper dust collection bags 837304- Bag retainer for 70401A Sunbelt EZ - 8 Sander Operator's Manual Page 17... -
Page 19: Wiring Diagram 8/00
EZ-8 Sander Wiring Diagram 8/00 Page 18 Sunbelt EZ - 8 Sander Operator's Manual... - Page 20 Sunbelt EZ - 8 Sander Operator's Manual Page 19...
- Page 21 Clarke ® American Sanders U. S. Warranty This Clarke American Sanders Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year from the date of purchase, when operated and maintained in accordance with Clarke American Sanders' Maintenance and Operations Instructions.
Need help?
Do you have a question about the EZ-8 and is the answer not in the manual?
Questions and answers