JVC HR-J6008UM Instructions Manual

Jvc video cassette recorder instructions manual
Hide thumbs Also See for HR-J6008UM:

Advertisement

Quick Links

LPT0534-001A
COPYRIGHT © 2001 VICTOR COMPANY OF JAPAN, LTD.
Dear Customer,
Thank you for purchasing the JVC VHS video cassette recorder.
Before use, please read the safety information and precautions to
ensure safe use of your new VCR.
CAUTIONS
WARNING: DANGEROUS VOLTAGE INSIDE
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
The POWER 1 button does not completely shut off mains
power from the unit, but switches operating current on and off.
"`" shows electrical power standby and " ! " shows ON.
This unit is produced to comply with Standard IEC 60065.
POWER SYSTEM:
This set operates on voltage of AC 110 – 220Vd, 50/60 Hz
with automatic switching.
Use the conversion plug (provided) depending on the type of
your AC WALL outlet.
The rating plate and safety caution are on the rear of the unit.
IMPORTANT:
It may be unlawful to record or play back copyrighted material
without the consent of the copyright owner.
VIDEO CASSETTE RECORDER
HR-J6008UM
INSTRUCTIONS
CAUTION
When you are not using the VCR for a long period of time, it
is recommended that you disconnect the power cord from the
AC outlet.
Dangerous voltage inside. Refer internal servicing to qualified
service personnel. To prevent electric shock or fire hazard,
remove the power cord from the AC outlet prior to
connecting or disconnecting any signal lead or aerial.
Changes or modifications not approved by JVC could void
user's authority to operate the equipment.
Caution on Replaceable lithium battery
The battery used in this device may present a fire or chemical
burn hazard if mistreated. Do not recharge, disassemble, heat
above 100°C or incinerate.
Replace battery with Panasonic (Matsushita Electric), Sanyo,
Sony or Maxell CR2025. Danger of explosion or Risk of fire if
the battery is incorrectly replaced.
Dispose of used battery promptly.
Keep away from children.
Do not disassemble and do not dispose of in fire.
Cassettes marked "VHS" (or "S-VHS") can be used with this
video cassette recorder. However, S-VHS recording is not
possible with this model.
This model is equipped with SQPB (S-VHS QUASI PLAYBACK)
that makes it possible to play back S-VHS recordings with
regular VHS resolution.
HQ VHS is compatible with existing VHS equipment.
Printed in Malaysia
0401 IYVfIDfPJ

Advertisement

Table of Contents
loading

Summary of Contents for JVC HR-J6008UM

  • Page 1 LPT0534-001A COPYRIGHT © 2001 VICTOR COMPANY OF JAPAN, LTD. Dear Customer, Thank you for purchasing the JVC VHS video cassette recorder. Before use, please read the safety information and precautions to ensure safe use of your new VCR. CAUTIONS WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
  • Page 2 Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the VCR’s power turned on for a few hours to let the moisture dry. How to use the Remote...
  • Page 3: Buttons, Connectors And Indicators

    Buttons, Connectors and Indicators Front Panel VIDEO/AUDIO input connectors Display panel Play indicator Record indicator Rear Panel AC power cord Cassette loading slot Remote sensor Timer mode indicator Channel and auxiliary input/Clock time Lithium battery compartment VCR mode indicator...
  • Page 4: On-Screen Display

    On-screen display If you press OK on the Remote when “SUPERIMPOSE” is set to “ON”, you can see the current VCR status on the TV screen. After about 5 seconds, indications other than the time counter disappear. To clear the time counter, press OK again.
  • Page 5: Basic Connections

    The VCR channel is preset to “CH3”. Set to “CH4” if CH3 is used for broadcasting in your area. Final preparation for use Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. Installing/Removing the lithium battery Be sure to connect the power plug to an AC outlet first before installing the lithium battery;...
  • Page 6: Initial Settings

    “SCAN COMPLETED” will be displayed on the screen. If “SCAN COMPLETED–NO SIGNAL–” is displayed on the screen, make sure that the antenna cable is connected to the VCR properly and press OK or on the Remote. The VCR will try Auto Channel Set again.
  • Page 7: Tuner Setting

    AUTO CHANNEL SET MANUAL CHANNEL SET VCR. Do not apply too much pressure when inserting. The VCR turns on, and the counter on the on-screen display is SELECT WITH ( , ) AND (OK) PRESS (MENU) TO END reset, automatically.
  • Page 8: Playback Features

    Locating beginning of timer recordings — Instant Review After ensuring that the VCR is turned off and that the timer mode is disengaged, press REVIEW on the Remote. The VCR turns on, and rewinds to the index code indicating the beginning of the last timer-recorded program, then begins playback automatically.
  • Page 9: Recording Features

    If no cassette is loaded, or during recording pause mode, you can select channel only by pressing FF[CH+] or REW[CH–]. If you connect the TV and the VCR only using the RF connection, press TV/VCR on the Remote so that the VCR mode indicator lights on the display panel, to view the program to be recorded.
  • Page 10: Express Timer Programing

    To use the VCR while it is in timer recording standby mode Press #, then press 1. After you use the VCR, press # again to put the VCR into timer recording standby mode. Checking, canceling or changing...
  • Page 11: Other Functions

    5 minutes if you are not in the timer recording standby mode at that time. Press # to put the VCR into timer recording standby mode. To clear the display, press & (CANCEL) on the Remote.
  • Page 12: Function Settings

    When this function is set to “ON”, various VCR status information (on-screen display) appears on the screen. NOTE: When you use this VCR as the playback VCR for editing a tape, be sure to set this function to “OFF”; otherwise, the VCR status HI-FI information (on-screen display) will be recorded on the edited tape.
  • Page 13 This Remote can control some functions of remote controllable TVs, cable boxes or DBS (Direct Broadcast Satellite) receivers listed below. Without setting, you can control a JVC TV. NOTES: Some unit’s brands have more than one code. If the unit does not function with a specified code, try other codes.
  • Page 14 05, 15, 16, 17, 24 TAIHAN (DEHAN) TELEVIEW 05, 16, 24 TOCOM 01, 04, 16 UNIKA 01, 17 UNIVERSAL 16, 17 VIDEOWAY 03, 09 ZENITH 03, 09 DBS RECEIVER BRAND CODE JVC (DISH Network) ECHOSTAR (DISH Network) PRIMESTAR RCA (DSS) SONY (DSS)
  • Page 15: Changing Remote Control Code

    VCR is initially set to respond to A code signals. You can easily modify your VCR and the Remote to respond to B code signals. When using two JVC VCRs, set two VCRs and their Remotes to different codes, so that you can operate these VCRs separately.
  • Page 16: Specifications

    Specifications GENERAL Power requirement : AC 110 V – 220 V Power consumption Power on : 16 W Power off : 2.0 W Temperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (W x H x D) : 360 mm x 94 mm x 247 mm Weight : 3.0 kg Format...

This manual is also suitable for:

Lpt0534-001aGem-rp1caGem-rp2asGem-rp3s

Table of Contents