Advertisement
1 MOTOR SYSTEM (KEY FOB)
TO LIFT
1. Remove the hand held remote control from its secure compartment.
2. Press activate/learn button until red LED illuminaties, then release.
The button has an automatic off circuit that times out after 10 min-
utes. It can be turned off at any time.
Press and hold this button.
EXTEND
Release when the kingpin is at the desired height.
ALL
LEGS
TO LOWER
Retract slideout rooms fully to their inboard position.
Press the activate/learn button to turn on remote control.
Press and hold this button.
RETRACT
Release when the legs are retracted.
ALL LEGS
TO PROGRAM REPLACEMENT KEY FOB
If you have a replacement key fob, it must be programmed to the
receiver.
1. Remove the hand held remote control from its secure compartment.
2. Press activate/learn button until red LED illuminates, then release.
The button has an automatic off circuit that times out after 10 min-
utes. It can be turned off at any time by pressing activation button
again.
3. Press and hold the Red Activate/Learn Switch for approximately 5
seconds until the LED begins to flash. The receiver is in the transmit-
ter code learning mode. All previous programs are erased.
4. Press any button on the transmitter (remote) and verify the Red LED
on the receiver stays lit for approximately 1/2 second, then returns to
the flashing modes of illumination. This indicates the transmitter is
identified by the receiver.
5. Repeat step 4 for additional transmitters that will be used with the
receiver.
6. If there are no additional transmitters to be programmed, in 5 sec-
onds the Red LED will return to constant illumination and the receiver
to normal operation.
7. Verify the remote is programmed with the receiver by pressing any
button on the remote and see if the corresponding function is activated.
2 MOTOR SYSTEM
TO LIFT
1. Remove the hand held remote control from its secure compartment.
2. Press activation switch. The switch has an automatic off circuit that
times out after 10 minutes.
3. When finished, the LED on the activation switch must not be lit.
4. PANIC STOP - Once the legs start moving, any button can be
depressed to panic stop the legs. The system stays activated. Push
to reset system.
RETRACT ALL
Press and hold the
EXTEND
E
Release when the kingpin is at the desired height.
ALL
ALL
R
LEGS
Use the individual leg button for adjustment.
INDIVIDUAL
Press and hold the
LEG
individual leg as needed until the front of the trail-
ADJUSTMENT
er is level.
TO LOWER
Retract slideout rooms fully to their inboard position.
Press the activation button to turn on remote control.
Press and hold the
RETRACT
E
ALL
Release when the legs are retracted.
ALL LEGS
R
Use the individual leg buttons for adjustment.
INDIVIDUAL
LEG
ADJUSTMENT
5TH WHEEL TRAILERS
button.
EXTEND ALL
(
) for an
EXTEND BUTTON
button, retract
RETRACT ALL
TROUBLESHOOTING
&
MAINTENTANCE CONTINUED ON PAGE
4 MOTOR SYSTEM
TO LIFT
1. Remove the hand held remote control from its secure compartment.
2. Press activation switch. The switch has an automatic off circuit that
times out after 10 minutes.
3. When finished, the LED on the activation switch must not be lit.
4. PANIC STOP - Once the legs start moving, any button can be
depressed to panic stop the legs. The system stays activated. Push
to reset system.
RETRACT ALL
Press the
AUTO
will extend automatically. Upon reaching the
EXTEND
ground and sensing a minimum load, the legs will
stop.
Press and hold the
FRONT
front levelers for 4".
LEGS
Press and hold the
REAR
levelers for 4".
LEGS
Press the
INDIVIDUAL
individual leg to make an adjustment as needed.
LEGS
TO LOWER
Retract slideout rooms fully to their inboard position.
Press the activation button to turn on remote control.
PANIC STOP - Once the legs start moving, any button can be
depressed to panic stop the legs. The system stays activated. Push
to reset system.
RETRACT ALL
Press and hold the
REAR
levelers for 4".
LEGS
Press and hold the
FRONT
levelers for 4".
LEGS
Press the
INDIVIDUAL
individual leg to make an adjustment as needed.
LEGS
Alternate between the
and
REAR
trailer higher than the rear. Retract the legs in this manner until all legs
are slightly off the ground.
Once the load is off the legs, press
AUTO
and release. The system will automatically finish
RETRACT
the retraction process.
MANUAL OVERRIDE: Refer to MPD 71125 for manual operation of landing gear,
direct drive legs, or rear levelers.
TRAILER CAN MOVE OR COLLAPSE
• Never exceed rated capacity of landing legs.
•
LANDING LEGS ARE NOT DESIGNED TO BE USED AS TRAILER JACKS
ing legs to lift the trailer during tire changes, axle work or trailer servicing (the
trailer weight will exceed the capacity of the landing legs). The landing legs
are designed to stabilize a portion of the trailer's weight. Support the
front end of the trailer with structural stands rated for the GVWR of the trailer.
• Chock both sides of trailer wheels before operating landing legs
• All legs must touch the ground or the surface at the same time.
• Retract landing legs and levelers completely before towing trailer.
3
and all four legs
AUTO EXTEND BUTTON
button to extend the
FRONT
button to extend the rear
REAR
button and the button for the
IND
button to retract the rear
REAR
button to retract the front
FRONT
button and the button for the
IND
buttons, keeping the front of the
FRONT
AUTO RETRACT
CAUTION
. Do not use the land-
8
Advertisement
