Table of Contents
Advertisement
-3-
PA11-VETTE provides two ways to control your iPod through car radio, namely P'ay'ist
Mode and Direct Mode.
2-1 Direct Mode: Search and select music on iPod directly just as you would in portable
use. The music will play back through your car stereo. Use the track up/down, fast
forward, and reverse buttons on your radio to control music playback. All control
functions on iPod are available for use as well. Please see section 4 in this manual
for additional information
2-2 P'ay'ist Mode: Operate and control the iPod like it is a CD changer. This mode allows
you to access up to five Playlists on the iPod. This is also referenced as the External
Control Mode of the iPod. Display of artist and song title on radio is supported by
PA11-VETTE only in this mode of operation. The detail of Playlist creation and
playback controls are in section 5 of this manual.
DIP switch #2 is for mode selection use. "ON" position is for P'ay'ist Mode and the "OFF"
position is for Direct Mode.
Note: Disconnect iPod from PA11-VETTE before switching DIP switch #2 for mode alteration.
2-3 Additional AUX INPUT Option Selection
PA11-VETTE interface adaptor is capable of connecting two audio sources to your
GM radio, including the iPod. The additional audio source connects to the RCA input
jack labeled as AUX INPUT. If you choose to use AUX INPUT, the DIP switch #1 at
the side of adaptor box must be set to the "OFF" position (factory presets it at "ON"
position).
The audio source at AUX INPUT can be accessed at CD 6 Track 1. CD1 to CD 4 are
for accessing Playlists, and CD 5 is for accessing all songs on iPod.
Operation of AUX
If the "AUX INPUT" option is selected, "CD 6 Track 1" gives access to the audio
source connected to AUX INPUT port. Adjust VOLUME, BASS, TREBLE and etc.
As you would normally do for the other program sources on the radio.
(Professional installation is strongly suggested. Installation in the CTS and SRX are
skill demanding works.)
3-1
Step 1-a- Set the 01 P switch #2 to "OFF" position only if the Direct Mode is preferred.
Step 1-b- If your vehicle is neither equipped with a GM XM satellite radio receiver nor
pre-wired for GM XM receiver, got to step 3 directly.
Step 2-a- Unplug the 16-pin connector from GM XM receiver and connect it to the
"FEMAL" 16-pin connector on
USkSPEC
cable CB-VET (Note: Pull-out the BLUE
color lock at the top side of the 16-pin connector before unplug it from the
receiver.)
Step 2-b- Plug
USkSPEC
CB-VET cable's "MALE" 16-pin connector to XM receiver.
Step 2-c- Set both DIP switch #3 and #4 at side panel of PA11-VETTE to "OFF" position.
Be sure the ACC power is OFF before go to next step.
Step 2-d- Connect
USkSPEC
cable CB-F12 to the 12-pin "MALE" connector CB-VET. Plug the
round DIN connector on CB-F12 to PA11-VETTE adopter where labeled "RADIO".
Step 2-e- Plug the blue wire on
USkSPEC
CB-VET cable to PA11-VETTE adaptor where
labeled "XM". Go to step 4 directly.
(Note: If
XM
service is not activated, the tree-at-charge
XM
preview and alert channels can be disables
by setting DIP switch #3 to OFF position and DIP switch #4 to ON position.)
Step 3-a- Remove radio from dash. Unplug the 24 pin and 12 pin connectors from the radio
and connect them to
USkSPEC
CAS-G7i cable.
Step 3-b- Plug
USkSPEC
CAS-G7i cable's 24 pin and 12 pin connectors to the radio.
Step 3-c- Set the DIP switch #3 to "ON" position and #4 to "OFF" position
Step 3-d- Connect CAS-F12 cable to G7i cable. Plug the round 01 N connector on CAS-F12
to adapter where labeled "RADIO". Go to Step 4.
Step 4 - Connect the audio output of your auxiliary sources to AUX input jack on PA11-
VETTE adapter box if the additional AUX option is selected by setting the DIP
switch #1 to "OFF" position.
Advertisement
Table of Contents
