Advertisement
J
~
PREiCISION
Instruction Manual for the Radio Controlled Analog Talking watch
(USA-EURO Muti-Band)
Your Analog Talking Watch is a Multi-Band Radio Control watch.
It is able to pick up signal from UK, GERMANY,
USA and JAPAN (60Khz only).
It recalls the Atomic Clock (which measures each second of time as 9,192,631,770
vibrations
of a cesium 133 atom in a
vacuum) and gives time which is accurate to 1 second every million years. Your Radio Controlled Watch even
accounts automatically
for daylight saving time.
You can set your watch to get UK, Germany, USA or Japan (60Khz only) signal as you wish.
Automatic
Time Setting
Your Analog talking radio controlled watch recalls your selected Atomic Clock signal automatically at 3:00AM every night. After
reception of signal it will show the official local time on the watch. Everything
is done automatically.
However, your watch can
also be manually set.
Basic Time and Date Features
Press the top right button to hear the TIME
Press the bottom right button to hear the DATE
Alarm,
Hourly
Time Announcement
and other Features
Your watch has many other features including an alarm and the option of an automatic
hourly time announcement.
Please read the full instruction
manual for details of how to set and use these functions.
Battery
Power
The battery life will depend on how often you use the talking function. Please follow the Battery Replacement
instructions
in this manual.
Button
Functions
S1: Time Announcement
Button
S2: Date Announcement
Button
S3: Alarm Button
S4: Reception
Status Button
S30S1
S4
S2
RATK-EURO/USA-PHD-02
Receiving
the time signal
Overnight
position your watch face down on a flat surface near a window. The signal will be updated at 3AM. You can
test this using the reception status test described earlier. If your watch is unable to make contact with the radio signal,
it will continue to function in the same way as a standard watch. The time will then be corrected the next time your
watch receives the time signal.
Country
Signal Selection
You can set your watch to receive either UK, Germany,
USA or Japan (60 KHz) signals.
When you select a new
country the watch will adjust to the local time. The second hand will run fast during the adjustment
and then return to
normal.
Selecting
the signal
for UK, Germany,
USA or Japan
(60
KHz only)
1. Press S4 for 5 seconds while the watch is in the real time mode until the watch speaks "Set Alarm, Press 10 o'clock
butto n to set"
2. Press S4 another 3 times, until the watch speaks "Global signal selection, only when you visit these countries.
Press
10 o'clock button to Set"
3. Press S3
4. After pressing S3, it says "Press 2 o'clock button to set, 8 o'clock button to confirm"
5. Press S1 to select UK, Germany, Japan (60 KHz only) or USA. (If you set to USA, you need to choose the correct
time zone from Pacific, Mountain, Central or Eastern).
6. Press S4 to confirrn after a new country has been selected.
7. After confirmation,
the watch will set to the local time of the country that you have selected. Wait until the hands stop
fast running and resume to norrnal.
8. Now, your watch will show the local time of the country that you have selected. (It will adjust for summer and winter
time).
9. The watch will receive the local atomic clock signal automatically
overnight.
Manual Signal
reception
The watch must be set to the right country before it can receive the signal (see above).
Position the watch face down on a flat surface near a window.
While the watch is in the Real Time mode,
1. Press S3 until the second hand stops.
The second-hand
of the watch will stop at the following reference
points:
-7 o'clock for USA signal reception
-12 o'clock for UK signal reception
-12:01 for Germany signal reception
-5 o'clock for Japan (60 KHz Signal only) signal reception
(If the second hand is not at the positions stated above it may need re-calibrating.
To re-calibrate
refer to the section
under TROUBLESHOOTING
later in this manual).
2. The watch takes about 5 to 14 minutes to pick up the signal. Wait until the watch has finished the signal receiving
procedure.
3. After the signal reception, wait until the hands stop fast running and resume to normal.
4. Push S4 once. If the reception was successful,
the watch will speak "Country name" follow by "Time Updated".
If the
reception failed, the watch will speak "Country name" follow by "Time Not Updated"
S1 Time Announcement
Press S1 to talk.
The watch will speak the Hour and Minute
S2 Date Announcement
i
Press S2 once to talk.
I
The watch will speak Day, Month, Date and Year after a signal is updated.
There is no "Day Talking" function after a new battery is installed until it gets a first signal.
I
S3 Alarm
I
1. Press S3 once and the watch will speak the Alarm time that has been set
2. If the Alarm is turned Off, the watchwill
speak "Alarm is Off'
S4 Reception
Status
1. Press S4 once while the watch is in the real time mode
2. If the reception was successful,
the watch will speak "Country name" follow by "Time Updated"
3. If the reception failed, the watch will speak "Country name" follow by "Time Not Updated"
(In some poor reception areas the sigrral may not up-date every night. Try moving the watch to a new location.
As the
watch is very accurate it can miss a few nights updating without any serious loss of accuracy.)
Set Daily Alarm
1. Press S4 for 5 seconds while the watch is in the real time mode until the watch speaks "Set Alarm, Press 10 o'clock
button to set"
2. Press S3
3. The watch says "Press 2 o'clock button to set Hour, 4 o'clock button for minute, 8 o'clock button to confirm"
4. Press S1 to set the Hour and S2 to set the Minute
5. Press S4 to confirm after you have set the Alarm time
6. After confirmation,
the watch will speak the Alarm time set
7. You can also check your Alarm time with by pressing S3 at any time
8. The Alarm will Beep for 30 seconds, press any button to turn off the alarm
9. The Alarm is a daily alarm, so it will alarm every day. To turn off the daily Alarm, follow the Alarm Off setting as
below.
•
Alarm
ON/OFF:
1. Press S4 for 5 seconds while the watch is in the real time mode until the watch speaks "Set Alarm, Press 10 o'clock
button to set"
2. Press S4 one more time, the watch speaks "Alarm ON/OFF,
Press 10 o'clock button to set"
3. Press S3
4. The watch says "Press 2 o'clock button to ON, 4 o'clock button to OFF, 8 o'clock button to confirm"
5. To turn OFF a daily alarm, Press S2. To turn ON a daily alarm, Press S1.
6. Press S4 to confirm
7. After a daily Alarm is confirmed to be OFF, the watch says "Alarm is OFF" when S3 is pressed.
Advertisement
