Advertisement
Operation Guide 3196
To turn Alarms
2
through
5
and the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select a one-time alarm
(alarm number
(
:00
).
2. Press A to toggle it on and off.
• The on/off status of Alarms
Time Signal is shown by indicators along the bottom of
the displays.
• The alarm on indicators and Hourly Time Signal on
Alarm on indicator
indicator are displayed in all modes.
• While an alarm is sounding, the applicable alarm on
Hourly Time Signal
indicator flashes on the display.
on indicator
To select the operation of Alarm
1
1. In the Alarm Mode, use D to select Alarm
2. Press A to cycle through the available settings in the sequence shown below.
Snooze on indicator (SNZ) and Alarm
One-time
Snooze
alarm on
alarm on
• The snooze on indicator (SNZ) and Alarm
• The snooze on indicator (SNZ) flashes during the 5-minute intervals between
alarms.
• The alarm indicator (Alarm
1
on and/or SNZ) flashes while the alarm is sounding.
Countdown Timer
The countdown timer can be set within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations in this section are performed in the
Seconds
Countdown Timer Mode, which you enter by pressing
Minutes
C.
Hours
To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
To set the countdown start time
1. In the Countdown Timer Mode, hold down A until the
hours setting of the countdown start time starts to flash,
which indicates the setting screen.
2. Press C to move the flashing between the hours and
minutes settings.
3. While a setting is flashing, use D to increase it.
• To set the starting value of the countdown time to
24 hours, set
4. Press A to exit the setting screen.
To turn auto-repeat on and off
1. In the Countdown Timer Mode, hold down A until the
Auto-repeat indicator
hours setting of the countdown start time starts to flash,
which indicates the setting screen.
2. Press B to toggle auto-repeat on (A.RPT displayed)
and off (A.RPT not displayed).
• Note that pressing B in the above operation also turns
on illumination.
• When the end of the countdown is reached while
auto-repeat is on, the alarm sounds, but the countdown
restarts from the beginning without stopping. You can
stop the countdown by pressing D and manually reset
to the start time by pressing A.
• The auto-repeat indicator appears in the Countdown
Timer Mode only.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
1/100 second
and two finishes.
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
Seconds
elapsed time measurement.
• All of the operations in this section are performed in the
Minutes
Stopwatch Mode, which you enter by pressing C.
Hours
2
through
5
) or the Hourly Time Signal
2
through
5
and the Hourly
1
.
on indicator
1
1
on indicator are displayed in all modes.
.
0:00
To measure times with the stopwatch
Elapsed time
Start
Stop
Re-start
Split time
Split
Split release
Start
(SPL displayed)
Two Finishes
Start
Split
Stop
First runner
Second runner
finishes.
finishes.
Display time of
first runner.
Dual Time
The Dual Time Mode lets you keep track of time in a different time zone.
• In the Dual Time Mode, the seconds count is synchronized with the seconds count
of the Timekeeping Mode.
To set the Dual Time
1. Press C to enter the Dual Time Mode.
2. In the Dual Time Mode, hold down A until the hour
setting starts to flash, which indicates the setting
screen.
3. Press C to change the selection in the following
sequence.
Seconds
Hour
Hour : Minutes
4. Press D to increase the setting.
5. Press A to exit the setting screen.
Illumination
An LED (light-emitting diode) and a light guide panel
illuminate the entire display for easy reading in the dark.
• Illumination may be hard to see when viewed under
direct sunlight.
• Illumination turns off automatically whenever an alarm
sounds.
• Frequent use of illumination runs down the battery life.
To illuminate the display
In any mode, press B to illuminate the display for about
one second.
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto return features
If you leave a screen with flashing digits for two or three minutes without performing
any operation, the watch automatically saves any settings you have made up to that
point and exits the setting screen.
Data and Setting Scrolling
The D button is used to scroll through setting screen data on the display. Holding
down this button during a scroll operation scrolls through the data at high speed.
Specifications
Accuracy at normal temperature: ±30 seconds a month
Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the week
Time system: Switchable between 12-hour and 24-hour formats
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Alarms: 5 Multi-function*alarms (Four one-time alarms; one snooze/one-time alarm);
Hourly Time Signal
* Alarm type: Daily alarm, Date alarm, 1-month alarm, Monthly alarm
Countdown Timer
Measuring unit: 1 second
Input range: 1 minute to 24 hours (1-minute increments and 1-hour increments)
Other: Auto-repeat function
Stopwatch
Measuring unit: 1/100 of a second
Measuring capacity: 23:59' 59.99''
Measuring modes: Elapsed time, split time, two finishes
Dual Time: Hour, minutes, seconds, p.m. (P)
Illumination: LED (light-emitting diode)
Battery: One lithium battery (Type: CR2025)
Approximately 10 years on type CR2025 (assuming alarm operation 10 sec./day,
and one illumination operation 1.5 sec./day)
Stop
Clear
Stop
Clear
Split release
Clear
Display time of
second runner.
Minutes
2
Advertisement
