Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HM Bike E-Ride
Summary of Contents for HM Bike E-Ride
- Page 1 E-RIDE User’s Guide...
-
Page 2: Table Of Contents
Table of contents Safety instructions ..............2 Diagram with e-bike specific components......3 Control panel ..............4 Important safety notes regarding battery charger....5 Charger function..............6 Battery safety notes ............7 Battery: further information and maintenance ......8 Charging the battery ............9 Remove & insert battery pack ...........10 Change fuse .......... -
Page 3: Safety Instructions
For handling and maintanance of the bicycle, please refer to the pass this user manual on to the HM Bike Owner Manual which is an integral part of this e-bike owner manual! new owner The HM Bike Owner Manual can be downloaded from www.hmbike.com... -
Page 4: Diagram With E-Bike Specific Components
Diagram of e-bike specific components 1 Motor 2 Battery 3 Controller 4 Sensor 5 Control panel 6 Rear light 7 Front light... -
Page 5: Control Panel
Control panel NOTE When pressing the MODE switch(5) the program starts with medium power assistance and the MED (4) LED light comes on. Each time you press MODE (5) you Battery capacity indication can choose the desired assistance level. (LOW / MED / HIGH) The battery charging status Control panel functions is indicated as follows:... -
Page 6: Important Safety Notes Regarding Battery Charger
Using this charger for batteries cables are not damaged. not supplied by HM Bike Never connect a damaged cable for the E-RIDE could risk catching fire, provoke electric shock and/or or plug to the power socket. cause serious injury. -
Page 7: Charger Function
Charger function Please use only the original charger which was supplied with the HM E-RIDE! This charger is specially made for the Lithium- Polimer battery (LiPo9). The LED (1) indicates the battery status as shown on the table below: Charging cycle and LED indication for LiPo battery... -
Page 8: Battery Safety Notes
Important safety notes concerning the battery! WARNING Before riding an HM E-RIDE, please Although the battery is constructed Keep the battery out of reach for read the here following notes in order for over 1000 charging cycles, children. to make best use of the battery. -
Page 9: Battery: Further Information And Maintenance
Battery: further information and maintenance In order to maximie the use None the less, we strongly NOTE of this battery, please consider the recomand to always disconnect following: the power plug (p. 9, (6) ) from The discharging of the battery the wall socket after the battery The battery will not charge when is due to chemical processes... -
Page 10: Charging The Battery
Charging the battery Charging when battery is ATTENTION NOTE not removed: The battery can either be charged BEFORE charging, please make sure while on the bike or the battery that the battery is switched ON (2) ii) connect the charging cable can be removed and charged and that the red led light (1) is plug (4) to the battery... -
Page 11: Remove & Insert Battery Pack
Removal and insertion of the battery to check the charging status (battery fuel gauge) NOTE The battery has a fuel gauge so that the charging status of the battery can also be checked when the battery is removed. To check the fuel gauge: NOTE ii) press nob and see To insert battery:... -
Page 12: Change Fuse
Change fuse NOTE ATTENTION Please make sure NOT to use a To change fuse: stronger fuse than the the original iv) remove fuse one (30Ah / 32V) which comes (1) ON/OFF v) insert new fuse and proceed with the battery which is installed in the reverse sequence on the bike. -
Page 13: Remove Front Wheel
Remove of the front wheel ii) disconnect the front motor cable plugs (3 & 4) and unhook cable from front fork cable guides (5). i) press both brake arms towards ii) pull out the bolt plastic cover (6) , each other (1) , pull the loosen bolt (7) pull the leadpipe (2) out of the cage wheel downwards and separate... -
Page 14: Insert Front Wheel
Insert the front wheel ii) Connect the front motor cable plugs (6 & 7) and hook cable to front fork cable guides (8). i) Insert the spacer which comes between fork and motor (1) on each side of the axle. After that, pull the wheel upwards and insert it in the fork drop outs (2);... -
Page 15: Adjust Stem & Handlebar Position
Adjust stem and seat post To adjust seat post height: ii) adjust seatpost (2) to the height Stem angle as well as handlebar position can be NOTE that best suits your riding position. adjusted easily without any particular tool! To do so: against the quick release clamp (3). - Page 16 HM Bike Consulting AG ch. des Châlets 5 CH-1279 Chavannes de Bogis www.hmbike.com...
Need help?
Do you have a question about the E-Ride and is the answer not in the manual?
Questions and answers